Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.
Abstract: An inflation–extension test with human vena cava
inferior was performed with the aim to fit a material model. The vein
was modeled as a thick–walled tube loaded by internal pressure and
axial force. The material was assumed to be an incompressible
hyperelastic fiber reinforced continuum. Fibers are supposed to be
arranged in two families of anti–symmetric helices. Considered
anisotropy corresponds to local orthotropy. Used strain energy
density function was based on a concept of limiting strain
extensibility. The pressurization was comprised by four pre–cycles
under physiological venous loading (0 – 4kPa) and four cycles under
nonphysiological loading (0 – 21kPa). Each overloading cycle was
performed with different value of axial weight. Overloading data
were used in regression analysis to fit material model. Considered
model did not fit experimental data so good. Especially predictions
of axial force failed. It was hypothesized that due to
nonphysiological values of loading pressure and different values of
axial weight the material was not preconditioned enough and some
damage occurred inside the wall. A limiting fiber extensibility
parameter Jm was assumed to be in relation to supposed damage.
Each of overloading cycles was fitted separately with different values
of Jm. Other parameters were held the same. This approach turned out
to be successful. Variable value of Jm can describe changes in the
axial force – axial stretch response and satisfy pressure – radius
dependence simultaneously.
Abstract: In the micro and nano-technology industry, the
«clean-rooms» dedicated to manufacturing chip, are equipped with
the most sophisticated equipment-tools. There use a large number of
resources in according to strict specifications for an optimum
working and result. The distribution of «utilities» to the production is
assured by teams who use a supervision tool.
The studies show the interest to control the various parameters of
production or/and distribution, in real time, through a reliable and
effective supervision tool. This document looks at a large part of the
functions that the supervisor must assure, with complementary
functionalities to help the diagnosis and simulation that prove very
useful in our case where the supervised installations are complexed
and in constant evolution.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Abstract: The Ministry of Defense (MoD) spends hundreds of
millions of dollars on software to support its infrastructure, operate
its weapons and provide command, control, communications,
computing, intelligence, surveillance, and reconnaissance (C4ISR)
functions. These and other all new advanced systems have a common
critical component is information technology. Defense and
Aerospace environment is continuously striving to keep up with
increasingly sophisticated Information Technology (IT) in order to
remain effective in today-s dynamic and unpredictable threat
environment. This makes it one of the largest and fastest growing
expenses of Defense. Hundreds of millions of dollars spent a year on
IT projects. But, too many of those millions are wasted on costly
mistakes. Systems that do not work properly, new components that
are not compatible with old once, trendily new applications that do
not really satisfy defense needs or lost though poorly managed
contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology Acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: It is shown that a modified UNIFAC model can be
applied to predict solubility of hydrocarbon gases and vapors in
hydrocarbon solvents. Very good agreement with experimental data
has been achieved. In this work we try to find best way for predicting
dimethyl ether solubility in liquid paraffin by using group
contribution theory.
Abstract: To define or predict incipient motion in an alluvial
channel, most of the investigators use a standard or modified form of
Shields- diagram. Shields- diagram does give a process to determine
the incipient motion parameters but an iterative one. To design
properly (without iteration), one should have another equation for
resistance. Absence of a universal resistance equation also magnifies
the difficulties in defining the model. Neural network technique,
which is particularly useful in modeling a complex processes, is
presented as a tool complimentary to modeling incipient motion.
Present work develops a neural network model employing the RBF
network to predict the average velocity u and water depth y based on
the experimental data on incipient condition. Based on the model,
design curves have been presented for the field application.
Abstract: In this study, a semi-cylinder obstacle placed in a
channel is handled to determine the effect of flow and heat transfer
around the obstacle. Both faces of the semi-cylinder are used in the
numerical analysis. First, the front face of the semi-cylinder is stated
perpendicular to flow, than the rear face is placed. The study is
carried out numerically, by using commercial software ANSYS 11.0.
The well-known κ-ε model is applied as the turbulence model.
Reynolds number is in the range of 104 to 105 and air is assumed as
the flowing fluid. The results showed that, heat transfer increased
approximately 15 % in the front faze case, while it enhanced up to 28
% in the rear face case.
Abstract: The current of professional bicycle pedal-s
manufacturing model mostly used casting, forging, die-casting
processing methods, so the paper used 7075 aluminum alloy which is
to produce the bicycle parts most commonly, and employs the
rigid-plastic finite element (FE) DEFORMTM 3D software to simulate
and to analyze the professional bicycle pedal design. First we use Solid
works 2010 3D graphics software to design the professional bicycle
pedal of the mold and appearance, then import finite element (FE)
DEFORMTM 3D software for analysis. The paper used rigid-plastic
model analytical methods, and assuming mode to be rigid body. A
series of simulation analyses in which the variables depend on
different temperature of forging billet, friction factors, forging speed,
mold temperature are reveal to effective stress, effective strain, damage
and die radial load distribution for forging bicycle pedal. The analysis
results hope to provide professional bicycle pedal forming mold
references to identified whether suit with the finite element results for
high-strength design suitability of aluminum alloy.
Abstract: We investigated this hypothesis that arterial CO2 pressure (PaCO2) drives ventilation (V.E) with a time delay duringrecovery from short impulse-like exercise (10 s) with work load of 200 watts. V.E and end tidal CO2 pressure (PETCO2) were measured continuously during rest, warming up, exercise and recovery periods. PaCO2 was predicted (PaCO2 pre) from PETCO2 and tidal volume (VT). PETCO2 and PaCO2 pre peaked at 20 s of recovery. V.E increased and peaked at the end of exercise and then decreased during recovery; however, it peaked again at 30 s of recovery, which was 10 s later than the peak of PaCO2 pre. The relationship between V. E and PaCO2pre was not significant by using data of them obtained at the same time but was significant by using data of V.E obtained 10 s later for data of PaCO2 pre. The results support our hypothesis that PaCO2 drives V.E with a time delay.
Abstract: Modern highly automated production systems faces
problems of reliability. Machine function reliability results in
changes of productivity rate and efficiency use of expensive
industrial facilities. Predicting of reliability has become an important
research and involves complex mathematical methods and
calculation. The reliability of high productivity technological
automatic machines that consists of complex mechanical, electrical
and electronic components is important. The failure of these units
results in major economic losses of production systems. The
reliability of transport and feeding systems for automatic
technological machines is also important, because failure of transport
leads to stops of technological machines. This paper presents
reliability engineering on the feeding system and its components for
transporting a complex shape parts to automatic machines. It also
discusses about the calculation of the reliability parameters of the
feeding unit by applying the probability theory. Equations produced
for calculating the limits of the geometrical sizes of feeders and the
probability of sticking the transported parts into the chute represents
the reliability of feeders as a function of its geometrical parameters.
Abstract: The acoustic and articulatory properties of fricative speech sounds are being studied using magnetic resonance imaging (MRI) and acoustic recordings from a single subject. Area functions were derived from a complete set of axial and coronal MR slices using two different methods: the Mermelstein technique and the Blum transform. Area functions derived from the two techniques were shown to differ significantly in some cases. Such differences will lead to different acoustic predictions and it is important to know which is the more accurate. The vocal tract acoustic transfer function (VTTF) was derived from these area functions for each fricative and compared with measured speech signals for the same fricative and same subject. The VTTFs for /f/ in two vowel contexts and the corresponding acoustic spectra are derived here; the Blum transform appears to show a better match between prediction and measurement than the Mermelstein technique.
Abstract: Unsteady boundary layer flow of an incompressible
micropolar fluid over a stretching sheet when the sheet is stretched in
its own plane is studied in this paper. The stretching velocity is
assumed to vary linearly with the distance along the sheet. Two equal
and opposite forces are impulsively applied along the x-axis so that the
sheet is stretched, keeping the origin fixed in a micropolar fluid. The
transformed unsteady boundary layer equations are solved
numerically using the Keller-box method for the whole transient from
the initial state to final steady-state flow. Numerical results are
obtained for the velocity and microrotation distributions as well as the
skin friction coefficient for various values of the material parameter K.
It is found that there is a smooth transition from the small-time
solution to the large-time solution.
Abstract: Many studies have shown that Artificial Neural
Networks (ANN) have been widely used for forecasting financial
markets, because of many financial and economic variables are nonlinear,
and an ANN can model flexible linear or non-linear
relationship among variables.
The purpose of the study was to employ an ANN models to
predict the direction of the Istanbul Stock Exchange National 100
Indices (ISE National-100).
As a result of this study, the model forecast the direction of the
ISE National-100 to an accuracy of 74, 51%.
Abstract: This study proposes and tests a rescapturing elements of perceived gain and loss that, by perceived value of medical tourism products, influencintention of potential customers. Data from 301 usable qwere tested against the research model using the structmodeling approach. The results indicated that perceivedkey predictor of customer intentions. As for benefimedical quality, service quality and enjoyment wcomponents that significantly influenced the perceptiRegarding sacrifice, the effects of perceived risk on pewere significant. The findings can provide insights intohow destination countries can make medical tourism a wfor themselves and international patients.KeywordsMedical tourism, perceived valueintention.
Abstract: The purpose of this article is to study the effects of
plants cover on overland flow and, therefore, its influences on the
amount of eroded and transported soil. In this investigation, all the
experiments were conducted in the LEGHYD laboratory using a
rainfall simulator and a soil tray. The experiments were conducted
using an experimental plot (soil tray) which is 2m long, 0.5 m wide
and 0.15 m deep. The soil used is an agricultural sandy soil (62,08%
coarse sand, 19,14% fine sand, 11,57% silt and 7,21% clay). Plastic
rods (4 mm in diameter) were used to simulate the plants at different
densities: 0 stem/m2 (bared soil), 126 stems/m², 203 stems/m², 461
stems/m² and 2500 stems/m²). The used rainfall intensity is 73mm/h
and the soil tray slope is fixed to 3°. The results have shown that the
overland flow velocities decreased with increasing stems density, and
the density cover has a great effect on sediment concentration.
Darcy–Weisbach and Manning friction coefficients of overland flow
increased when the stems density increased. Froude and Reynolds
numbers decreased with increasing stems density and, consequently,
the flow regime of all treatments was laminar and subcritical. From
these findings, we conclude that increasing the plants cover can
efficiently reduce soil loss and avoid denuding the roots plants.
Abstract: The hydrodynamics behavior of fluid flow in microconverging
plates is investigated analytically. Effects of Knudsen number () on the microchannel hydrodynamics behavior and the
coefficient of friction are investigated. It is found that as increases the slip in the hydrodynamic boundary condition increases.
Also, the coefficient of friction decreases as increases.
Abstract: There are many problems associated with the World Wide
Web: getting lost in the hyperspace; the web content is still accessible only
to humans and difficulties of web administration. The solution to these
problems is the Semantic Web which is considered to be the extension
for the current web presents information in both human readable and
machine processable form. The aim of this study is to reach new
generic foundation architecture for the Semantic Web because there
is no clear architecture for it, there are four versions, but still up to
now there is no agreement for one of these versions nor is there a
clear picture for the relation between different layers and
technologies inside this architecture. This can be done depending on
the idea of previous versions as well as Gerber-s evaluation method
as a step toward an agreement for one Semantic Web architecture.
Abstract: This study focuses on the development of triangular fuzzy numbers, the revising of triangular fuzzy numbers, and the constructing of a HCFN (half-circle fuzzy number) model which can be utilized to perform more plural operations. They are further transformed for trigonometric functions and polar coordinates. From half-circle fuzzy numbers we can conceive cylindrical fuzzy numbers, which work better in algebraic operations. An example of fuzzy control is given in a simulation to show the applicability of the proposed half-circle fuzzy numbers.
Abstract: Magetan area is going to be the object of this research
which is located in East Java, Indonesia. The data were obtained
from 270 civil servants working at the Magetan District government.
The data were analyzed using the Structural Equation Modeling with
Partial Least Square program. The research showed the following
findings: (1) job motivation variable has a positive and significant
effect on organizational citizenship behavior (OCB); (2) work
environment has positive and significant effect on OCB; (3)
leadership variable has positive and significant effect on OCB; (4)
job motivation variable has no significant effect on job satisfaction;
(5) work environment variable has no significant effect on job
satisfaction; (6) leadership variable has no significant effect on job
satisfaction; (7) OCB is positively and significantly associated with
job satisfaction; (8) job satisfaction variable is positively and
significantly correlated with quality of public service at the Magetan
District government.