Abstract: Recent medical studies have investigated the importance of enteral feeding and the use of feeding pumps for recovering patients unable to feed themselves or gain nourishment and nutrients by natural means. The most of enteral feeding system uses a peristaltic tube pump. A peristaltic pump is a form of positive displacement pump in which a flexible tube is progressively squeezed externally to allow the resulting enclosed pillow of fluid to progress along it. The squeezing of the tube requires a precise and robust controller of the geared motor to overcome parametric uncertainty of the pumping system which generates due to a wide variation of friction and slip between tube and roller. So, this paper proposes fuzzy adaptive controller for the robust control of the peristaltic tube pump. This new adaptive controller uses a fuzzy multi-layered architecture which has several independent fuzzy controllers in parallel, each with different robust stability area. Out of several independent fuzzy controllers, the most suited one is selected by a system identifier which observes variations in the controlled system parameter. This paper proposes a design procedure which can be carried out mathematically and systematically from the model of a controlled system. Finally, the good control performance, accurate dose rate and robust system stability, of the developed feeding pump is confirmed through experimental and clinic testing.
Abstract: Ultrasound is useful in demonstrating bone mineral
density of regenerating osseous tissue as well as structural alterations.
A proposed ultrasound method, which included ultrasonography and
acoustic parameters measurement, was employed to evaluate its
efficacy in monitoring the bone callus changes in a rabbit tibial
distraction osteogenesis (DO) model.
The findings demonstrated that ultrasonographic images depicted
characteristic changes of the bone callus, typical of histology findings,
during the distraction phase. Follow-up acoustic parameters
measurement of the bone callus, including speed of sound, reflection
and attenuation, showed significant linear changes over time during
the distraction phase. The acoustic parameters obtained during the
distraction phase also showed moderate to strong correlation with
consolidated bone callus density and micro-architecture measured by
micro-computed tomography at the end of the consolidation phase.
The results support the preferred use of ultrasound imaging in the
early monitoring of bone callus changes during DO treatment.
Abstract: Response surface methodology was used for
quantitative investigation of water and solids transfer during osmotic
dehydration of beetroot in aqueous solution of salt. Effects of
temperature (25 – 45oC), processing time (30–150 min), salt
concentration (5–25%, w/w) and solution to sample ratio (5:1 – 25:1)
on osmotic dehydration of beetroot were estimated. Quadratic
regression equations describing the effects of these factors on the
water loss and solids gain were developed. It was found that effects
of temperature and salt concentrations were more significant on the
water loss than the effects of processing time and solution to sample
ratio. As for solids gain processing time and salt concentration were
the most significant factors. The osmotic dehydration process was
optimized for water loss, solute gain, and weight reduction. The
optimum conditions were found to be: temperature – 35oC,
processing time – 90 min, salt concentration – 14.31% and solution
to sample ratio 8.5:1. At these optimum values, water loss, solid gain
and weight reduction were found to be 30.86 (g/100 g initial sample),
9.43 (g/100 g initial sample) and 21.43 (g/100 g initial sample)
respectively.
Abstract: A biophysically based multilayer continuum model of the facial soft tissue composite has been developed for simulating wrinkle formation. The deformed state of the soft tissue block was determined by solving large deformation mechanics equations using the Galerkin finite element method. The proposed soft tissue model is composed of four layers with distinct mechanical properties. These include stratum corneum, epidermal-dermal layer (living epidermis and dermis), subcutaneous tissue and the underlying muscle. All the layers were treated as non-linear, isotropic Mooney Rivlin materials. Contraction of muscle fibres was approximated using a steady-state relationship between the fibre extension ratio, intracellular calcium concentration and active stress in the fibre direction. Several variations of the model parameters (stiffness and thickness of epidermal-dermal layer, thickness of subcutaneous tissue layer) have been considered.
Abstract: Three dimensional simulations in tube in tube heat
exchangers are investigated numerically in this study. In these
simulations forced convective heat transfer and laminar flow of
single-phase water are considered. In order to measure heat transfer
parameters in these heat exchangers, FLUENT CFD Solver is used in
this numerical method. For the purpose of creating geometry and
exert boundary and initial conditions in the present model, finite
volume method in Computational Fluid Dynamics is used in this
study. In the present study, at each Z-location, variation of local
temperatures, heat flux and Nusselt number at the whole tube is
investigated in detail. Thereafter, averaged computational Nusselt
number in this model is calculated. In addition, conceivable pressure
drops have been obtained at each Z-location in this model. Then,
pressure drop values in the present model are explored. Finally, all
the numerical results for this kind of heat exchanger will be discussed
precisely.
Abstract: Cutting fluids, usually in the form of a liquid, are
applied to the chip formation zone in order to improve the cutting
conditions. Cutting fluid can be expensive and represents a biological
and environmental hazard that requires proper recycling and
disposal, thus adding to the cost of the machining operation. For
these reasons dry cutting or dry machining has become an
increasingly important approach; in dry machining no coolant or
lubricant is used. This paper discussed the effect of the dry cutting on
cutting force and tool life when machining aerospace materials
(Haynes 242) with using two different coated carbide cutting tools
(TiAlN and TiN/MT-TiCN/TiN). Response surface method (RSM)
was used to minimize the number of experiments. ParTiAlN Swarm
Optimisation (PSO) models were developed to optimize the
machining parameters (cutting speed, federate and axial depth) and
obtain the optimum cutting force and tool life. It observed that
carbide cutting tool coated with TiAlN performed better in dry
cutting compared with TiN/MT-TiCN/TiN. On other hand, TiAlN
performed more superior with using of 100 % water soluble coolant.
Due to the high temperature produced by aerospace materials, the
cutting tool still required lubricant to sustain the heat transfer from
the workpiece.
Abstract: One of the most basic functions of control engineers is
tuning of controllers. There are always several process loops in the
plant necessitate of tuning. The auto tuned Proportional Integral
Derivative (PID) Controllers are designed for applications where
large load changes are expected or the need for extreme accuracy and
fast response time exists. The algorithm presented in this paper is
used for the tuning PID controller to obtain its parameters with a
minimum computing complexity. It requires continuous analysis of
variation in few parameters, and let the program to do the plant test
and calculate the controller parameters to adjust and optimize the
variables for the best performance. The algorithm developed needs
less time as compared to a normal step response test for continuous
tuning of the PID through gain scheduling.
Abstract: Although many researchers have studied the flow
hydraulics in compound channels, there are still many complicated problems in determination of their flow rating curves. Many different
methods have been presented for these channels but extending them
for all types of compound channels with different geometrical and
hydraulic conditions is certainly difficult. In this study, by aid of nearly 400 laboratory and field data sets of geometry and flow rating
curves from 30 different straight compound sections and using artificial neural networks (ANNs), flow discharge in compound channels was estimated. 13 dimensionless input variables including relative depth, relative roughness, relative width, aspect ratio, bed
slope, main channel side slopes, flood plains side slopes and berm
inclination and one output variable (flow discharge), have been used
in ANNs. Comparison of ANNs model and traditional method
(divided channel method-DCM) shows high accuracy of ANNs model results. The results of Sensitivity analysis showed that the relative depth with 47.6 percent contribution, is the most effective input parameter for flow discharge prediction. Relative width and
relative roughness have 19.3 and 12.2 percent of importance, respectively. On the other hand, shape parameter, main channel and
flood plains side slopes with 2.1, 3.8 and 3.8 percent of contribution, have the least importance.
Abstract: In this paper, a wavelet based method is proposed to
identify the constant coefficients of a second order linear system and
is compared with the least squares method. The proposed method
shows improved accuracy of parameter estimation as compared to the
least squares method. Additionally, it has the advantage of smaller
data requirement and storage requirement as compared to the least
squares method.
Abstract: The mathematical modeling of different biological
processes is usually used to predict or assess behavior of systems in
which these processes take place. This study deals with mathematical
and computer modeling of bi-substrate enzymatic reactions with
ping-pong mechanism, which play an important role in different
biochemical pathways. Besides that, three models of competitive
inhibition were designed using different software packages. The main
objective of this study is to represent the results from in silico
investigation of bi-substrate enzymatic reactions with ordered pingpong
mechanism in the presence of competitive inhibitors, as well as
to describe in details the inhibition effects. The simulation of the
models with certain kinetic parameters allowed investigating the
behavior of reactions as well as determined some interesting aspects
concerning influence of different cases of competitive inhibition.
Simultaneous presence of two inhibitors, competitive to the S1 and S2
substrates have been studied. Moreover, we have found the pattern of
simultaneous influence of both inhibitors.
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: The experiments were performed in a batch set up
under different concentrations of Cu (II) (0.2 g.l-1 to 0.9 g.l-1), pH (4-
6), temperatures (20oC – 40oC) with varying teak leaves powder (as
biosorbent) dosage of 0.3 g.l-1 to 0.5 g.l-1. The kinetics of interactions
were tested with pseudo first order Lagergran equation and the value
for k1 was found to be 6.909 x 10-3 min-1. The biosorption data gave
a good fit with Langmuir and Fruendlich isotherms and the Langmuir
monolayer capacity (qm) was found to be 166.78 mg. g-1. Similarly
the Freundlich adsorption capacity (Kf) was estimated as 2.49 l g-1.
The mean values of the thermodynamic parameters ΔH, ΔS, and ΔG
were -62.42 KJ. mol-1, -0.219 KJ.mol-1 K-1 and -1.747 KJ.mol-1 at
293 K from a solution containing 0.4 g l-1 of Cu(II) showing the
biosorption to be thermodynamically favourable. These results show
good potentiality of using teak leaves as a biosorbent for the removal
of Cu(II) from aqueous solutions.
Abstract: Background Contact lens (CL) wear can cause
changes in blinking and corneal staining. Aims and Objectives To
determine the effects of CL materials (HEMA and SiHy) on
spontaneous blink rate, blinking patterns and corneal staining after 2
months of wear. Methods Ninety subjects in 3 groups (control,
HEMA and SiHy) were assessed at baseline and 2-months. Blink rate
was recorded using a video camera. Blinking patterns were assessed
with digital camera and slit lamp biomicroscope. Corneal staining
was graded using IER grading scale Results There were no significant
differences in all parameters at baseline. At 2 months, CL wearers
showed significant increment in average blink rate (F1.626, 47.141 =
7.250, p = 0.003; F2,58 = 6.240, p = 0.004) and corneal staining (χ2
2,
n=30 = 31.921, p < 0.001; χ2
2, n=30 = 26.909, p < 0.001). Conclusion
Blinking characteristics and corneal staining were not influence by
soft CL materials.
Abstract: This paper propose a new circuit design which
monitor total leakage current during standby mode and generates the
optimal reverse body bias voltage, by using the adaptive body bias
(ABB) technique to compensate die-to-die parameter variations.
Design details of power monitor are examined using simulation
framework in 65nm and 32nm BTPM model CMOS process.
Experimental results show the overhead of proposed circuit in terms
of its power consumption is about 10 μW for 32nm technology and
about 12 μW for 65nm technology at the same power supply voltage
as the core power supply. Moreover the results show that our
proposed circuit design is not far sensitive to the temperature
variations and also process variations. Besides, uses the simple
blocks which offer good sensitivity, high speed, the continuously
feedback loop.
Abstract: Aeration by a plunging water jet is an energetically attractive way to effect oxygen-transfer than conventional oxygenation systems. In the present study, a new type of conical shaped plunging aeration device is fabricated to generate hollow inclined ined plunging jets (jet plunge angle of π/3 ) to investigate its oxygen transfer capacity. The results suggest that the volumetric oxygen-transfer coefficient and oxygen-transfer efficiency of the conical plunging jet aerator are competitive with other types of aeration systems. Relationships of volumetric oxygen-transfer coefficient with jet power per unit volume and jet parameters are also proposed. The suggested relationships predict the volumetric oxygentransfer coefficient within a scatter of ± 15% . Further, the application of Support Vector Machines on the experimental data revealed its utility in the prediction of volumetric oxygen-transfer coefficient and development of conical plunging jet aerators.
Abstract: The optimal design of PI controller for Automatic Generation Control in two area is presented in this paper. The concept of Dual mode control is applied in the PI controller, such that the proportional mode is made active when the rate of change of the error is sufficiently larger than a specified limit otherwise switched to the integral mode. A digital simulation is used in conjunction with the Hooke-Jeeve’s optimization technique to determine the optimum parameters (individual gain of proportional and integral controller) of the PI controller. Integrated Square of the Error (ISE), Integrated Time multiplied by Absolute Error(ITAE) , and Integrated Absolute Error(IAE) performance indices are considered to measure the appropriateness of the designed controller. The proposed controller are tested for a two area single nonreheat thermal system considering the practical aspect of the problem such as Deadband and Generation Rate Constraint(GRC). Simulation results show that dual mode with optimized values of the gains improved the control performance than the commonly used Variable Structure .
Abstract: In this article, we are going to do a study that consist in the configuration of a link between an earth station to broadcast multimedia service and a user of this service via a geostationary satellite in Ka- band and the set up of the different components of this link and then to make the calculation of the link budget for this system. The application carried out in this work, allows us to calculate the link budget in both directions: the uplink and downlink, as well as all parameters used in the calculation and the development of a link budget. Finally, we will try to verify using the application developed the feasibility of implementation of this system.
Abstract: Gluconic acid is one of interesting chemical products
in industries such as detergents, leather, photographic, textile, and
especially in food and pharmaceutical industries. Fermentation is an
advantageous process to produce gluconic acid. Mathematical
modeling is important in the design and operation of fermentation
process. In fact, kinetic data must be available for modeling. The
kinetic parameters of gluconic acid production by Aspergillus niger
in batch culture was studied in this research at initial substrate
concentration of 150, 200 and 250 g/l. The kinetic models used were
logistic equation for growth, Luedeking-Piret equation for gluconic
acid formation, and Luedeking-Piret-like equation for glucose
consumption. The Kinetic parameters in the model were obtained by
minimizing non linear least squares curve fitting.
Abstract: This paper presents a methodical approach for designing and optimizing process parameters in oil blending industries. Twenty seven replicated experiments were conducted for production of A-Z crown super oil (SAE20W/50) employing L9 orthogonal array to establish process response parameters. Power law model was fitted to experimental data and the obtained model was optimized applying the central composite design (CCD) of response surface methodology (RSM). Quadratic model was found to be significant for production of A-Z crown supper oil. The study recognized and specified four new lubricant formulations that conform to ISO oil standard in the course of analyzing the batch productions of A-Z crown supper oil as: L1: KV = 21.8293Cst, BS200 = 9430.00Litres, Ad102=11024.00Litres, PVI = 2520 Litres, L2: KV = 22.513Cst, BS200 = 12430.00 Litres, Ad102 = 11024.00 Litres, PVI = 2520 Litres, L3: KV = 22.1671Cst, BS200 = 9430.00 Litres, Ad102 = 10481.00 Litres, PVI= 2520 Litres, L4: KV = 22.8605Cst, BS200 = 12430.00 Litres, Ad102 = 10481.00 Litres, PVI = 2520 Litres. The analysis of variance showed that quadratic model is significant for kinematic viscosity production while the R-sq value statistic of 0.99936 showed that the variation of kinematic viscosity is due to its relationship with the control factors. This study therefore resulted to appropriate blending proportions of lubricants base oil and additives and recommends the optimal kinematic viscosity of A-Z crown super oil (SAE20W/50) to be 22.86Cst.
Abstract: The main objective of this work is to provide a fault detection and isolation based on Markov parameters for residual generation and a neural network for fault classification. The diagnostic approach is accomplished in two steps: In step 1, the system is identified using a series of input / output variables through an identification algorithm. In step 2, the fault is diagnosed comparing the Markov parameters of faulty and non faulty systems. The Artificial Neural Network is trained using predetermined faulty conditions serves to classify the unknown fault. In step 1, the identification is done by first formulating a Hankel matrix out of Input/ output variables and then decomposing the matrix via singular value decomposition technique. For identifying the system online sliding window approach is adopted wherein an open slit slides over a subset of 'n' input/output variables. The faults are introduced at arbitrary instances and the identification is carried out in online. Fault residues are extracted making a comparison of the first five Markov parameters of faulty and non faulty systems. The proposed diagnostic approach is illustrated on benchmark problems with encouraging results.