Abstract: Preparation of nanoparticles of cerium oxide and
adsorption of bovine serum albumin on them were studied. Particle
size distribution and influence of pH on zeta potential of prepared
CeO2 were determined. Average size of prepared cerium oxide
nanoparticles was 9 nm. The simultaneous measurements of the
bovine serum albumin adsorption and zeta potential determination of
the (adsorption) suspensions were carried out. The adsorption
isotherms were found to be of typical Langmuir type; values of the
bovine serum albumin adsorption capacities were calculated.
Increasing of pH led to decrease of zeta potential and decrease of
adsorption capacity of cerium oxide nanoparticles. The maximum
adsorption capacity was found for strongly acid suspension (am =
118 mg/g). The samples of nanoceria with positive zeta potential
adsorbed more bovine serum albumin on the other hand, the samples
with negative zeta potential showed little or no protein adsorption.
Surface charge or better say zeta potential of CeO2 nanoparticles
plays the key role in adsorption of proteins on such type of materials.
Abstract: Paper presents a study about dynamic effects obtained
from the dynamic load testing of the city highway bridges in Latvia
carried out from 2005 to 2012. 9 prestressed concrete bridges and 4
composite bridges were considered. 11 of 13 bridges were designed
according to the Eurocodes but two according to the previous
structural codes used in Latvia (SNIP 2.05.03-84). The dynamic
properties of the bridges were obtained by heavy vehicle passing the
bridge roadway with different driving speeds and with or without
even pavement. The obtained values of the Dynamic amplification
factor (DAF) and the bridge natural frequency were analyzed and
compared to the values of built-in traffic load models provided in
Eurocode 1. The actual DAF values for even bridge pavement in the
most cases are smaller than the value adopted in Eurocode 1. Vehicle
speed for uneven pavements significantly influence Dynamic
amplification factor values.
Abstract: In this paper, we propose a new packing strategy to
find a free resource for run-time mapping of application tasks to
NoC-based Heterogeneous MPSoC. The proposed strategy minimizes
the task mapping time in addition to placing the communicating tasks
close to each other. To evaluate our approach, a comparative study is
carried out for a platform containing single task supported PEs.
Experiments show that our strategy provides better results when
compared to latest dynamic mapping strategies reported in the
literature.
Abstract: The bean (Phaseolus vulgaris L.) is one of the best
known of the legumes, and it has a long cultivation tradition in Italy.
The territory of “Subappennino Dauno” (southern Italy) is at around
700 m a.s.l. and is predominantly grown with cereals, olive trees and
grapevines. Ecotypes of white beans to eat dry (such as cannellini
beans) are also grown, which are sought for their palatability, high
digestibility, and ease of cooking. However, these are not easy to find
on the market due to their low production in relatively small areas
and on small family farms that use seeds handed down from
generation to generation. The introduction of these ecotypes in plain
areas of the Puglia region would provide an opportunity to promote
the diffusion of this type of bean. To investigate the adaptability of
these ecotypes in plain environments (Cerignola, in southern Italy) a
comparative trial was carried out between three ‘Monti Dauni’
ecotypes (E1, E2, E3) that are native to mountain areas and the
similar commercial variety, ‘Cannellini’. The data provide useful
information about the quantitative and qualitative characteristics of
these ecotypes when grown in lowland environments. Ecotype E3
provided the greatest bean production (2.34 t ha-1) compared to
‘Cannellini’ (1.28 t ha-1) and the other ecotypes (0.55 and 0.40 t ha-1,
for E1 and E2, respectively), due to its greater plant growth and the
larger size of the seed (and thickness, in particular). Finally, ecotype
E2 provided the greatest protein content (31.2%), although not
significantly different from the commercial cultivar ‘Cannellini’
(32.1%).
Abstract: This paper presents a study on Proportional Resonant
(PR) current control with additional PR harmonic compensators for
Grid Connected Photovoltaic (PV) Inverters. Both simulation and
experimental results will be presented. Testing was carried out on a
3kW Grid-Connected PV Inverter which was designed and
constructed for this research.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: Thanks to informational technologies development
every sphere of economics is becoming more and more datacentralized
as people are generating huge datasets containing
information on any aspect of their life. Applying research of such
data to human resources management allows getting scarce statistics
on labor market state including salary expectations and potential
employees’ typical career behavior, and this information can become
a reliable basis for management decisions.
The following article presents results of career behavior research
based on freely accessible resume data. Information used for study is
much wider than one usually uses in human resources surveys. That
is why there is enough data for statistically significant results even
for subgroups analysis.
Abstract: This study is purposed to develop an efficient fault
detection method for Global Navigation Satellite Systems (GNSS)
applications based on adaptive noise covariance estimation. Due to the
dependence on radio frequency signals, GNSS measurements are
dominated by systematic errors in receiver’s operating environment.
In the proposed method, the pseudorange and carrier-phase
measurement noise covariances are obtained at time propagations and
measurement updates in process of Carrier-Smoothed Code (CSC)
filtering, respectively. The test statistics for fault detection are
generated by the estimated measurement noise covariances. To
evaluate the fault detection capability, intentional faults were added to
the filed-collected measurements. The experiment result shows that
the proposed method is efficient in detecting unhealthy measurements
and improves GNSS positioning accuracy against fault occurrences.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: This paper presents reliability indices evaluation of the
rotor core magnetization of the induction motor operated as a self
excited induction generator by using probability distribution approach
and Monte Carlo simulation. Parallel capacitors with calculated
minimum capacitive value across the terminals of the induction motor
operated as a SEIG with unregulated shaft speed have been connected
during the experimental study. A three phase, 4 poles, 50Hz, 5.5 hp,
12.3A, 230V induction motor coupled with DC Shunt Motor was
tested in the electrical machine laboratory with variable reactive loads.
Based on this experimental study, it is possible to choose a reliable
induction machines operated as a SEIG for unregulated renewable
energy application in remote area or where grid is not available.
Failure density function, cumulative failure distribution function,
survivor function, hazard model, probability of success and
probability of failure for reliability evaluation of the three phase
induction motor operating as a SEIG have been presented graphically
in this paper.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: The current study explored the effect of economic
development, financial development and institutional quality on
environmental destruction in upper-middle income countries during
the time period of 1999-2011. The dependent variable is logarithm of
carbon dioxide emissions that can be considered as an index for
destruction or quality of the environment given to its effects on the
environment. Financial development and institutional development
variables as well as some control variables were considered. In order
to study cross-sectional correlation among the countries under study,
Pesaran and Friz test was used. Since the results of both tests show
cross-sectional correlation in the countries under study, seemingly
unrelated regression method was utilized for model estimation. The
results disclosed that Kuznets’ environmental curve hypothesis is
confirmed in upper-middle income countries and also, financial
development and institutional quality have a significant effect on
environmental quality. The results of this study can be considered by
policy makers in countries with different income groups to have
access to a growth accompanied by improved environmental quality.
Abstract: Lately, asynchronous discussion forum is integrated in
higher educational institutions as it may increase learning process,
learners’ understanding, achievement and knowledge construction.
The asynchronous discussion forum is used to complement the
traditional, face-to-face learning session in hybrid learning courses.
However, studies have proven that students’ engagement in online
forums is still unconvincing. Thus, the aim of this study is to
investigate the motivating factors and obstacles that affect the
learners’ engagement in asynchronous discussion forum. This study
is carried out in one of the public higher educational institutions in
Malaysia with 18 postgraduate students as samples. The authors have
developed a 40-items questionnaire based on literature review. The
results indicate several factors that have encouraged or limited
students’ engagement in asynchronous discussion forum: (a) the
practices or behaviors of peers, or instructors, (b) the needs for the
discussions, (c) the learners’ personalities, (d) constraints in
continuing the discussion forum, (e) lack of ideas, (f) the level of
thoughts, (g) the level of knowledge construction, (h) technical
problems, (i) time constraints and (j) misunderstanding. This study
suggests some recommendations to increase the students’
engagement in online forums. Finally, based upon the findings, some
implications are proposed for further research.
Abstract: This experimental study aims at studying the
conversion of macro-algae into bioethanol under several steps of
procedure: preparation, pre-treatment, fermentation, and distillation.
The main objective of this work was to investigate the role of buffer’s
type as a stabiliser of pH level and fermentation time on the yield of
ethanol. For this purpose, experiments were carried out on biomass
macro-algae to de-couple the pre-treatment and fermentation
processes from those associated with distillation process. β-
glucosidase was used as cellulose decomposer during hydrolysis step
and yeast was used during fermentation process. The species of
macro-algae utilised as energy feedstock was Ulva lactuca and it was
harvested from southern coast of Central of Java Island – Indonesia.
Experiments were conducted in a simple fermenter over a different
buffer: citrate buffer and acetic buffer, and over a range of
fermentation times between 5 to 20 days. The ethanol production was
found to be significantly affected by both variables. The optimum
time of fermentation was 10 days with citrate buffer; result in
0.88458% of ethanol, and the ethanol content after distillation
process was shown 0.985015%.
Abstract: In the present study, we have synthesized Cr and Fe
doped zinc oxide (ZnO) nanostructures (Zn1-δCraFebO; where δ = a +
b = 20%, a = 5, 6, 8 & 10% and b = 15, 14, 12 & 10%) via sol-gel
method at different doping concentrations. The synthesized samples
were characterized for structural properties by X-ray diffractrometer
and field emission scanning electron microscope and the optical
properties were carried out through photoluminescence and UVvisible
spectroscopy. The particle size calculated through field
emission scanning electron microscope varies from 41 to 96 nm for
the samples synthesized at different doping concentrations. The
optical band gaps calculated through UV-visible spectroscopy are
found to be decreasing from 3.27 to 3.02 eV as the doping
concentration of Cr increases and Fe decreases.
Abstract: This study discovers a novel framework of individual
level technology adoption known as I-P (Individual- Privacy) towards
health information application in Smart National Identity Card. Many
countries introduced smart national identity card (SNIC) with various
applications such as health information application embedded inside
it. However, the degree to which citizens accept and use some of the
embedded applications in smart national identity remains unknown to
many governments and application providers as well. Moreover, the
factors of trust, perceived risk, Privacy concern and perceived
credibility need to be incorporated into more comprehensive models
such as extended Unified Theory of Acceptance and Use of
Technology known as UTAUT2. UTAUT2 is a mainly widespread
and leading theory up to now. This research identifies factors
affecting the citizens’ behavioural intention to use health information
application embedded in SNIC and extends better understanding on
the relevant factors that the government and the application providers
would need to consider in predicting citizens’ new technology
acceptance in the future. We propose a conceptual framework by
combining the UTAUT2 and Privacy Calculus Model constructs and
also adding perceived credibility as a new variable. The proposed
framework may provide assistance to any government planning,
decision, and policy makers involving e-government projects.
Empirical study may be conducted in the future to provide proof and
empirically validate this I-P framework.