Abstract: The study area is Zaria, located in the basement
complex of northern Nigeria. The rock type forming the major part of
the Zaria batholith is granite. This research work was carried out to
compare the responses of seismic refraction tomography and
resistivity tomography in the same geologic environment and under
the same conditions. Hence, the choice of the site that has a visible
granitic outcrop that extends across a narrow stream channel and is
flanked by unconsolidated overburden, a neutral profile that was
covered by plain overburden and a site with thick lateritic cover
became necessary. The results of the seismic and resistivity
tomography models reveals that seismic velocity and resistivity does
not always simultaneously increase with depth, but their responses in
any geologic environment are determined by changes in the
mechanical and chemical content of the rock types rather than depth.
Abstract: The measured data obtained from sensors in
continuous monitoring of civil structures are mainly used for modal
identification and damage detection. Therefore, when modal
identification analysis is carried out the quality in the identification of
the modes will highly influence the damage detection results. It is
also widely recognized that the usefulness of the measured data used
for modal identification and damage detection is significantly
influenced by the number and locations of sensors. The objective of
this study is the numerical implementation of two widely known
optimum sensor placement methods in beam-like structures.
Abstract: A total of 150 meat type chickens comprising 50 each
of Arbor Acre, Marshall and Ross were used for this study which
lasted for 10 weeks at the Federal University of Agriculture,
Abeokuta, Nigeria. Growth performance data were collected from the
third week through week 10 and data obtained were analysed using
the Generalized Linear Model Procedure. Heritability estimates (h2)
for body dimensions carried out on the chicken strains ranged from
low to high. Marshall broiler chicken strain had the highest h2 for
body weight 0.46±0.04, followed by Arbor Acre and Ross with h2
being 0.38±0.12 and 0.26±0.06, respectively. The repeatability
estimates for body weight in the three broiler strains were high, and it
ranged from 0.70 at week 4 to 0.88 at week 10. Relationships
between the body weight and linear body measurements in the broiler
chicken strains were positive and highly significant (p > 0.05).
Abstract: In order to investigate the effect of Plant Growth
Promoting Rhizobacteria (PGPR) and rhizobium bacteria on grain
yield and some agronomic traits of mungbean (Vigna radiate L.), an
experiment was carried out based on randomized complete block
design with three replications in Malekshahi, Ilam province, Iran
during 2012-2013 cropping season. Experimental treatments
consisted of control treatment, inoculation with rhizobium bacteria,
rhizobium bacteria and Azotobacter, rhizobium bacteria and
Azospirillum, rhizobium bacteria and Pseudomonas, rhizobium
bacteria, Azotobacter and Azospirillum, rhizobium bacteria,
Azotobacter and Pseudomonas, rhizobium bacteria, Azospirillum and
Pseudomonas and rhizobium bacteria, Azotobacter, Azospirillum and
Pseudomonas. The results showed that the effect of PGPR and
rhizobium bacteria were significant affect on grain and its
components in mungbean plant. Grain yield significantly increased
by PGPR and rhizobium bacteria, so that the maximum grain yield
was obtained from rhizobium bacteria + Azospirillum +
Pseudomonas with the amount of 2287 kg.ha-1 as compared to
control treatment. Excessive application of chemical fertilizers causes
environmental and economic problems. That is, the overfertilization
of P and N leads to pollution due to soil erosion and runoff water, so
the use of PGPR and rhizobium bacteria can be justified due to
reduce input costs, increase in grain yield and environmental friendly.
Abstract: The European Union Survey on Income and Living
Conditions (EU-SILC) is a popular survey which provides
information on income, poverty, social exclusion and living
conditions of households and individuals in the European Union.
The EU-SILC contains variables which may contain outliers. The
presence of outliers can have an impact on the measures and
indicators used by the EU-SILC. In this paper, we used data sets
from various countries to analyze the presence of outliers. In addition,
we obtain some indicators after removing these outliers, and a
comparison between both situations can be observed. Finally, some
conclusions are obtained.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: The paper a summary of the results of concretes with
partial substitution of natural aggregates with recycled concrete is
solved. Design formulas of the concretes were characterised with 20,
40 and 60% substitution of natural 8-16mm fraction aggregates with
a selected recycled concrete of analogous coarse fractions. With the
product samples an evaluation of coarse fraction aggregates influence
on fresh concrete consistency and concrete strength in time was
carried out. The results of concretes with aggregates substitution will
be compared to reference formula containing only the fractions of
natural aggregates.
Abstract: Currently, biological control programs in greenhouse
crops involve the use, at the same time, several natural enemies
during the crop cycle. Also, large number of plant species grown in
greenhouses, among them, the used cultivars are also wide. However,
the cultivar effects on entomophagous species efficacy (predators and
parasitoids) have been scarcely studied. A new method had been
developed, using the factitious prey or host Ephestia kuehniella. It
allow us to evaluate, under greenhouse or controlled conditions
(semi-field), the cultivar effects on the entomophagous species
effectiveness. The work was carried out in greenhouse tomato crop. It
has been found the biological and ecological activities of predatory
species (Nesidiocoris tenuis) and egg-parasitoid (Trichogramma
achaeae) can be well represented with the use of the factitious prey
or host; being better in the former than the latter. The data found in
the trial are shown and discussed. The developed method could be
applied to evaluate new plant materials before making available to
farmers as commercial varieties, at low costs and easy use.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: The article presents the results of the application of
artificial neural networks to separate the fluorescent contribution of
nanodiamonds used as biomarkers, adsorbents and carriers of drugs
in biomedicine, from a fluorescent background of own biological
fluorophores. The principal possibility of solving this problem is
shown. Use of neural network architecture let to detect fluorescence
of nanodiamonds against the background autofluorescence of egg
white with high accuracy - better than 3 ug/ml.
Abstract: Frequent pattern mining is the process of finding a
pattern (a set of items, subsequences, substructures, etc.) that occurs
frequently in a data set. It was proposed in the context of frequent
itemsets and association rule mining. Frequent pattern mining is used
to find inherent regularities in data. What products were often
purchased together? Its applications include basket data analysis,
cross-marketing, catalog design, sale campaign analysis, Web log
(click stream) analysis, and DNA sequence analysis. However, one of
the bottlenecks of frequent itemset mining is that as the data increase
the amount of time and resources required to mining the data
increases at an exponential rate. In this investigation a new algorithm
is proposed which can be uses as a pre-processor for frequent itemset
mining. FASTER (FeAture SelecTion using Entropy and Rough sets)
is a hybrid pre-processor algorithm which utilizes entropy and roughsets
to carry out record reduction and feature (attribute) selection
respectively. FASTER for frequent itemset mining can produce a
speed up of 3.1 times when compared to original algorithm while
maintaining an accuracy of 71%.
Abstract: Fly ash is an important waste, produced in thermal
power plants which causes very important environmental pollutions.
For this reason the usage and evaluation the fly ash in various areas
are very important. Nearly, 15 million tons/year of fly ash is
produced in Turkey. In this study, usage of fly ash with diatomite and
molasses for heavy metal (Cd) adsorption from wastewater is
investigated. The samples of Seyitomer region fly ash were analyzed
by X-ray fluorescence (XRF) and Scanning Electron Microscope
(SEM) then diatomite (0 and 1% in terms of fly ash, w/w) and
molasses (0-0.75 mL) were pelletized under 30 MPa of pressure for
the usage of cadmium (Cd) adsorption in wastewater. After the
adsorption process, samples of Seyitomer were analyzed using
Optical Emission Spectroscopy (ICP-OES). As a result, it is seen that
the usage of Seyitomer fly ash is proper for cadmium (Cd) adsorption
and an optimum adsorption yield with 52% is found at a compound
with Seyitomer fly ash (10 g), diatomite (0.5 g) and molasses (0.75
mL) at 2.5 h of reaction time, pH:4, 20ºC of reaction temperature and
300 rpm of stirring rate.
Abstract: A generalized vortex lattice method for complex
lifting surfaces with flap and aileron deflection is formulated. The
method is not restricted by the linearized theory assumption and
accounts for all standard geometric lifting surface parameters:
camber, taper, sweep, washout, dihedral, in addition to flap and
aileron deflection. Thickness is not accounted for since the physical
lifting body is replaced by a lattice of panels located on the mean
camber surface. This panel lattice setup and the treatment of different
wake geometries is what distinguish the present work form the
overwhelming majority of previous solutions based on the vortex
lattice method. A MATLAB code implementing the proposed
formulation is developed and validated by comparing our results to
existing experimental and numerical ones and good agreement is
demonstrated. It is then used to study the accuracy of the widely used
classical vortex-lattice method. It is shown that the classical approach
gives good agreement in the clean configuration but is off by as much
as 30% when a flap or aileron deflection of 30° is imposed. This
discrepancy is mainly due the linearized theory assumption
associated with the conventional method. A comparison of the effect
of four different wake geometries on the values of aerodynamic
coefficients was also carried out and it is found that the choice of the
wake shape had very little effect on the results.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c
Abstract: Three dimensional non-Interlaced carbon fibre
reinforced silicon carbide (3-D-Cf/SiC) composites with pyrocarbon
interphase were fabricated using isothermal chemical vapor
infiltration (ICVI) combined with polymer impregnation pyrolysis
(PIP) process. Polysilazane (PSZ) is used as a preceramic polymer to
obtain silicon carbide matrix. Thermo gravimetric analysis (TGA),
Infrared spectroscopic analysis (IR) and X-ray diffraction (XRD)
analysis were carried out on PSZ pyrolysed at different temperatures
to understand the pyrolysis and obtaining the optimum pyrolysing
condition to yield β-SiC phase. The density of the composites was
1.94 g cm-3 after the 3-D carbon preform was SiC infiltrated for 280 h
with one intermediate polysilazane pre-ceramic PIP process.
Mechanical properties of the composite materials were investigated
under tensile, flexural, shear and impact loading. The values of
tensile strength were 200 MPa at room temperature (RT) and 195
MPa at 500°C in air. The average RT flexural strength was 243 MPa.
The lower flexural strength of these composites is because of the
porosity. The fracture toughness obtained from single edge notched
beam (SENB) technique was 39 MPa.m1/2. The work of fracture
obtained from the load-displacement curve of SENB test was 22.8
kJ.m-2. The composites exhibited excellent impact resistance and the
dynamic fracture toughness of 44.8 kJ.m-2 is achieved as determined
from instrumented Charpy impact test. The shear strength of the
composite was 93 MPa, which is significantly higher compared 2-D
Cf/SiC composites. Microstructure evaluation of fracture surfaces
revealed the signatures of fracture processes and showed good
support for the higher toughness obtained.
Abstract: Male factor infertility due to endocrine disturbances
such as abnormalities in prolactin levels are encountered in a
significant proportion. This case control study was carried out to
determine the effects of prolactin on the male reproductive tract,
using 200 male white rats. The rats were maintained as the control
group (G1), hypoprolactinaemic group (G2), 3 hyperprolactinaemic
groups induced using oral largactil (G3), low dose fluphenazine (G4)
and high dose fluphenazine (G5). After 100 days, rats were subjected
to serum prolactin (PRL) level measurements and for basic seminal
fluid analysis (BSA). The difference between serum PRL
concentrations of rats in G2, G3, G4 and G5 as compared to the
control group were highly significant by Student’s t-test (p
Abstract: The purposes of this research were to study concepts
and strategies of human resource development in the automotive
manufacturers and to articulate the proposals against the government
about the human resource development for automotive industry. In
the present study, qualitative study was an in-depth interview in
which the qualitative data were collected from the executive or the
executive of human resource division from five automotive
companies - Toyota Motor (Thailand) Co., Ltd., Nissan Motor
(Thailand) Co., Ltd., Mitsubishi Motors (Thailand) Co., Ltd., Honda
Automobile (Thailand) Co., Ltd., and Suzuki Motor (Thailand) Co.,
Ltd. Qualitative data analysis was performed by using inter-coder
agreement technique. The research findings were as follows:
The external factors included the current conditions of the
automotive industry, government’s policy related to the automotive
industry, technology, labor market and human resource development
systems of the country. The internal factors included management,
productive management, organizational strategies, leadership,
organizational culture and philosophy of human resource
development. These factors were affected to the different concept of
human resources development -the traditional human resource
development and the strategies of human resource development. The
organization focuses on human resources as intellectual capital and
uses the strategies of human resource development in all
development processes. The strategies of human resource
development will enhance the ability of human resources in the
organization and the country.
Abstract: Concerns on corrosion and effective coating
protection of double hull tankers and bulk carriers in service have
been raised especially in water ballast tanks (WBTs). Test
protocols/methodologies specifically that which is incorporated in the
International Maritime Organisation (IMO), Performance Standard
for Protective Coatings for Dedicated Sea Water ballast tanks (PSPC)
are being used to assess and evaluate the performance of the coatings
for type approval prior to their application in WBTs. However, some
of the type approved coatings may be applied as very thick films to
less than ideally prepared steel substrates in the WBT. As such films
experience hygrothermal cycling from operating and environmental
conditions, they become embrittled which may ultimately result in
cracking. This embrittlement of the coatings is identified as an
undesirable feature in the PSPC but is not mentioned in the test
protocols within it. There is therefore renewed industrial research
aimed at understanding this issue in order to eliminate cracking and
achieve the intended coating lifespan of 15 years in good condition.
This paper will critically review test protocols currently used for
assessing and evaluating coating performance, particularly the IMO
PSPC.
Abstract: This paper presents the voltage problem location
classification using performance of Least Squares Support Vector
Machine (LS-SVM) and Learning Vector Quantization (LVQ) in
electrical power system for proper voltage problem location
implemented by IEEE 39 bus New- England. The data was collected
from the time domain simulation by using Power System Analysis
Toolbox (PSAT). Outputs from simulation data such as voltage, phase
angle, real power and reactive power were taken as input to estimate
voltage stability at particular buses based on Power Transfer Stability
Index (PTSI).The simulation data was carried out on the IEEE 39 bus
test system by considering load bus increased on the system. To verify
of the proposed LS-SVM its performance was compared to Learning
Vector Quantization (LVQ). The results showed that LS-SVM is faster
and better as compared to LVQ. The results also demonstrated that the
LS-SVM was estimated by 0% misclassification whereas LVQ had
7.69% misclassification.
Abstract: In the present study, M2 high speed steels were
fabricated by using electro-slag rapid remelting process. Carbide
structure was analysed and the fracture toughness and hardness were
also measured after austenitization treatment at 1190 and 1210oC
followed by tempering treatment at 535oC for billets with various
diameters from 16 to 60 mm. Electro-slag rapid remelting (ESRR)
process is an advanced ESR process combined by continuous casting
and successfully employed in this study to fabricate a sound M2 high
speed ingot. Three other kinds of commercial M2 high speed steels,
produced by traditional method, were also analysed for comparison.
Distribution and structure of eutectic carbides of the ESRR billet were
found to be comparable to those of commercial alloy and so was the
fracture toughness.