Abstract: A large variety of pipe flange is required in marine
and construction industry. Pipe flanges are usually welded or screwed
to the pipe end and are connected with bolts. This approach is very
simple and widely used for a long time; however, it results in high
development cost and low productivity, and the productions made by
this approach usually have safety problem at the welding area. In this
research, a new approach of forming pipe flange based on cold
forging and floating die concept is presented. This innovative
approach increases the effectiveness of the material usage and save
the time cost compared with conventional welding method. To ensure the dimensional accuracy of the final product, the finite
element analysis (FEA) was carried out to simulate the process of
cold forging, and the orthogonal experiment methods were used to
investigate the influence of four manufacturing factors (pin die angle,
pipe flange angle, rpm, pin die distance from clamp jig) and predicted
the best combination of them. The manufacturing factors were
obtained by numerical and experimental studies and it shows that the
approach is very useful and effective for the forming of pipe flange,
and can be widely used later.
Abstract: Growing human population has placed increased
demands on water supplies and spurred a heightened interest in
desalination infrastructure. Key elements of the economics of
desalination projects are thermal and electrical inputs. With growing
concerns over use of fossil fuels to (indirectly) supply these inputs,
coupling of desalination with nuclear power production represents a
significant opportunity. Individually, nuclear and desalination
technologies have a long history and are relatively mature. For
desalination, Reverse Osmosis (RO) has the lowest energy inputs.
However, the economically driven output quality of the water
produced using RO, which uses only electrical inputs, is lower than the
output water quality from thermal desalination plants. Therefore,
modern desalination projects consider that RO should be coupled with
thermal desalination technologies (MSF, MED, or MED-TVC) with
attendant steam inputs to permit blending to produce various qualities
of water. A large nuclear facility is well positioned to dispatch large
quantities of both electrical and thermal power. This paper considers
the supply of thermal energy to a large desalination facility to examine
heat balance impact on the nuclear steam cycle. The APR1400 nuclear
plant is selected as prototypical from both a capacity and turbine cycle
heat balance perspective to examine steam supply and the impact on
electrical output. Extraction points and quantities of steam are
considered parametrically along with various types of thermal
desalination technologies to form the basis for further evaluations of
economically optimal approaches to the interface of nuclear power
production with desalination projects. In our study, the
thermodynamic evaluation will be executed by DE-TOP, an IAEA
sponsored program. DE-TOP has capabilities to analyze power
generation systems coupled to desalination plants through various
steam extraction positions, taking into consideration the isolation loop
between the nuclear and the thermal desalination facilities (i.e., for
radiological isolation).
Abstract: Processing of high-silicon bauxite on the base of the
traditional clinkering method is related to high power consumption
and capital investments, which makes production of alumina from
those ores non-competitive in terms of basic economic showings. For
these reasons, development of technological solutions enabling to
process bauxites with various chemical and mineralogical structures
efficiently with low level of thermal power consumption is important.
Flow sheet of the studies on washability of ores from the Timanskoe
and the Severo-Onezhskoe deposits is on the base of the flotation
method.
Abstract: Zinc borate is an important inorganic hydrate borate
material, which can be used as a flame retardant agent and corrosion
resistance material. This compound can loss its structural water
content at higher than 290°C. Due to thermal stability; Zinc Borate
can be used as flame retardant at high temperature process of plastic
and gum. In this study, the ultrasonic reaction of zinc borates were
studied using hydrozincite (Zn5(CO3)2·(OH)6) and boric acid
(H3BO3) raw materials. Before the synthesis raw materials were
characterized by X-Ray Diffraction (XRD) and Fourier Transform
Infrared Spectroscopy (FT-IR). Ultrasonic method is a new
application on the zinc borate synthesis. The synthesis parameters
were set to 90°C reaction temperature and 55 minutes of reaction
time, with 1:1, 1:2, 1:3, 1:4 and 1:5 molar ratio of starting materials
(Zn5(CO3)2·(OH)6 : H3BO3). After the zinc borate synthesis, the
products were analyzed by XRD and FT-IR. As a result, optimum
molar ratio of 1:5 is determined for the synthesis of zinc borates with
ultrasonic method.
Abstract: This paper tries to answer to the questions whether or
not trade openness causes economic growth and trade policy changes
are good for Turkey as a developing country in global economy
before and after 1980. We employ Johansen co-integration and
Granger causality tests with error correction modeling based on
vector autoregressive. Using WDI data from the pre-1980 and the
post-1980, we find that trade openness and economic growth are cointegrated
in the second term only. Also the results suggest a lack of
long-run causality between our two variables. These findings may
imply that trade policy of Turkey should concentrate more on extra
complementary economic reforms.
Abstract: The research explores the relationship between
management responsibility and corporate governance of listed
companies in Kazakhstan. This research employs firm level data of
selected listed non-financial firms and firm level data “operational”
financial sector, consisted from banking sector, insurance companies
and accumulated pension funds using multivariate regression analysis
under fixed effect model approach. Ownership structure includes
institutional ownership, managerial ownership and private investor’s
ownership. Management responsibility of the firm is expressed by the
decision of the firm on amount of leverage. Results of the cross
sectional panel study for non-financial firms showed that only
institutional shareholding is significantly negatively correlated with
debt to equity ratio. Findings from “operational” financial sector
show that leverage is significantly affected only by the CEO/Chair
duality and the size of financial institutions, and insignificantly
affected by ownership structure. Also, the findings show, that there is
a significant negative relationship between profitability and the debt
to equity ratio for non-financial firms, which is consistent with
pecking order theory. Generally, the found results suggest that
corporate governance and a management responsibility play
important role in corporate performance of listed firms in
Kazakhstan.
Abstract: In this paper, various methods of providing restricted
earth fault protection are discussed. The proper operation of high and
low impedance Restricted Earth Fault (REF) protection for various
applications has been discussed. The maloperation of a relay due to
improper placement of CTs has been identified and a simple/unique
solution has been proposed in this work with a case study. Moreover,
it is found that the proper placement of CT in high impedance method
will provide the same result with reduced CT. This methodology has
been successfully implemented in Al Takreer refinery for a 2000
KVA transformer. The outcome of the paper may be included in
IEEEC37.91 standard to give the proper guidance for protection
engineers to sort out the issues related to mal functioning of REF
relays.
Abstract: Developing our knowledge of when pineapple roots
grow can lead to improved water, fertilizer applications, and more
precise culture management. This paper presents current
understanding of morphological traits in pineapple roots, highlighting
studies using incubation periods and various solid MS media treated
with different sucrose concentrations and pH, which directly assess in
vitro environmental factors. Rooting parameters had different optimal
sucrose concentrations and incubation periods. All shoots failed to
root in medium supplemented with sucrose at 5 g/L and no roots
formed within the first 45 days in medium enriched with sucrose at
10 g/L. After 75 days, all shoots rooted in medium enriched with 10
and 20 g/L sucrose. Moreover, MS medium supplied with 20 g/L
sucrose resulted in the longest and the highest number of roots with
27.3 mm and 4.7, respectively. Root function, such as capacity for P
and N uptake, declined rapidly with root length. As a result, the
longer the incubation period, the better the rooting responses would
be.
Abstract: This study and the field test comparisons were carried
out on the Algerian Derguna – Setif transmission systems. The
transmission line of normal voltage 225 kV is 65 km long,
transported and uses twin bundle conductors protected with two
shield wires of transposed galvanized steel. An iterative finite-element method is used to solve Poisons
equation. Two algorithms are proposed for satisfying the current
continuity condition and updating the space-charge density. A new approach to the problem of corona discharge in
transmission system has been described in this paper. The effect of
varying the configurations and wires number is also investigated. The
analysis of this steady is important in the design of HVDC
transmission lines. The potential and electric field have been
calculating in locations singular points of the system.
Abstract: An industrial system for the production of white
liquor of a paper industry, Klabin Paraná Papéis, formed by ten
reactors was modeled, simulated, and analyzed. The developed model
considered possible water losses by evaporation and reaction, in
addition to variations in volumetric flow of lime mud across the
reactors due to composition variations. The model predictions agreed
well with the process measurements at the plant and the results
showed that the slaking reaction is nearly complete at the third
causticizing reactor, while causticizing ends by the seventh reactor.
Water loss due to slaking reaction and evaporation occurs more
pronouncedly in the slaking reaction than in the final causticizing
reactors; nevertheless, the lime mud flow remains nearly constant
across the reactors.
Abstract: This article presents an alternative collapse capacity
intensity measure in the three elements form which is influenced by
the spectral ordinates at periods longer than that of the first mode
period at near and far source sites. A parameter, denoted by β, is
defined by which the spectral ordinate effects, up to the effective
period (2T1), on the intensity measure are taken into account. The
methodology permits to meet the hazard-levelled target extreme
event in the probabilistic and deterministic forms. A MATLAB code
is developed involving OpenSees to calculate the collapse capacities
of the 8 archetype RC structures having 2 to 20 stories for regression
process. The incremental dynamic analysis (IDA) method is used to
calculate the structure’s collapse values accounting for the element
stiffness and strength deterioration. The general near field set
presented by FEMA is used in a series of performing nonlinear
analyses. 8 linear relationships are developed for the 8structutres
leading to the correlation coefficient up to 0.93. A collapse capacity
near field prediction equation is developed taking into account the
results of regression processes obtained from the 8 structures. The
proposed prediction equation is validated against a set of actual near
field records leading to a good agreement. Implementation of the
proposed equation to the four archetype RC structures demonstrated
different collapse capacities at near field site compared to those of
FEMA. The reasons of differences are believed to be due to
accounting for the spectral shape effects.
Abstract: Lyophilization, also called freeze-drying, is an
important dehydration technique mainly used for pharmaceuticals.
Food industry also uses lyophilization when it is important to retain
most of the nutritional quality, taste, shape and size of dried products
and to extend their shelf life. Vacuum-Induced during freezing cycle
(VI) has been used in order to control ice nucleation and,
consequently, to reduce the time of primary drying cycle of
pharmaceuticals preserving quality properties of the final product.
This procedure has not been applied in freeze drying of foods. The
present work aims to investigate the effect of VI on the lyophilization
drying time, final moisture content, density and reconstitutional
properties of mango (Mangifera indica L.) slices (MS) and mango
pulp-maltodextrin dispersions (MPM) (30% concentration of total
solids). Control samples were run at each freezing rate without using
induced vacuum. The lyophilization endpoint was the same for all
treatments (constant difference between capacitance and Pirani
vacuum gauges). From the experimental results it can be concluded
that at the high freezing rate (0.4°C/min) reduced the overall process
time up to 30% comparing process time required for the control and
VI of the lower freeze rate (0.1°C/min) without affecting the quality
characteristics of the dried product, which yields a reduction in costs
and energy consumption for MS and MPM freeze drying. Controls
and samples treated with VI at freezing rate of 0.4°C/min in MS
showed similar results in moisture and density parameters.
Furthermore, results from MPM dispersion showed favorable values
when VI was applied because dried product with low moisture
content and low density was obtained at shorter process time
compared with the control. There were not found significant
differences between reconstitutional properties (rehydration for MS
and solubility for MPM) of freeze dried mango resulting from
controls, and VI treatments.
Abstract: Ceramic obtained on the base of aluminum oxide has
wide application range, because it has unique properties, for example,
wear-resistance, dielectric characteristics, and exploitation ability at
high temperatures and in corrosive atmosphere. Low temperature
synthesis of α-Al2O3 is energo-economical process and it is topical
for developing technologies of corundum ceramics fabrication. In the present work possibilities of low temperature transformation
of oxyhydroxides in α-Al2O3, during the presence of small amount of
rare–earth elements compounds (also Th, Re), have been discussed.
Aluminum unstable oxyhydroxides have been obtained by hydrolysis
of aluminium isopropoxide, nitrates, sulphate, and chloride in
alkaline environment at 80-90ºC temperatures. β-Al(OH)3 has been
received from aluminum powder by ultrasonic development. Drying
of oxyhydroxide sol has been conducted with presence of various
types seeds, which amount reaches 0,1-0,2% (mas). Neodymium,
holmium, thorium, lanthanum, cerium, gadolinium, disprosium
nitrates and rhenium carbonyls have been used as seeds and they
have been added to the sol specimens in amount of 0.1-0.2% (mas)
calculated on metals. Annealing of obtained gels is carried out at 70–
1100ºC for 2 hrs. The same specimen transforms in α-Al2O3 at
1100ºC. At this temperature in case of presence of lanthanum and
gadolinium transformation takes place by 70-85%. In case of
presence of thorium stabilization of γ-and θ-phases takes place. It is
established, that thorium causes inhibition of α-phase generation at
1100ºC, and at the time when in all other doped specimens α-phase is
generated at lower temperatures (1000-1050ºC). Synthesis of various
type compounds and simultaneous consolidation has developed in the
furnace of OXY-GON. Composite materials containing oxide and
non-oxide components close to theoretical data have been obtained in
this furnace respectively. During the work the following devices have
been used: X-ray diffractometer DRON-3M (Cu-Kα, Ni filter,
2º/min), High temperature vacuum furnace OXY-GON, electronic
scanning microscopes Nikon ECLIPSE LV 150, NMM-800TRF,
planetary mill Pulverisette 7 premium line, SHIMADZU Dynamic
Ultra Micro Hardness Tester, DUH-211S, Analysette 12 Dyna sizer.
Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: Financial inclusion has become a crucially important
factor in debates on economic inequality posing challenges to the
financial systems of countries around the world. Nowadays
governments and banks are concerned about creating products that
allow access to wide sectors of the population. The creation of
banking products by the financial sector for people with low incomes
tends to lead to improvements in the quality of life of vulnerable parts
of the population. In countries with notable social and economic
inequalities, financial inclusion is a key aspect for equitable
economic growth. This study is based on the case of Colombia, which is a country
with a strong record of economic growth over the past decade.
Nevertheless, corruption, unemployment, and poverty contribute to
uncertainty regarding the country’s future growth prospects. This study wants to explain the situation of financial exclusion and
financial inclusion with respect to the Colombian case. Financial
inclusion is going to be studied from the perspective of social
innovation.
Abstract: In the present study we have investigated axial
buckling characteristics of nanocomposite beams reinforced by
single-walled carbon nanotubes (SWCNTs). Various types of beam
theories including Euler-Bernoulli beam theory, Timoshenko beam
theory and Reddy beam theory were used to analyze the buckling
behavior of carbon nanotube-reinforced composite beams.
Generalized differential quadrature (GDQ) method was utilized to
discretize the governing differential equations along with four
commonly used boundary conditions. The material properties of the
nanocomposite beams were obtained using molecular dynamic (MD)
simulation corresponding to both short-(10,10) SWCNT and long-
(10,10) SWCNT composites which were embedded by amorphous
polyethylene matrix. Then the results obtained directly from MD
simulations were matched with those calculated by the mixture rule
to extract appropriate values of carbon nanotube efficiency
parameters accounting for the scale-dependent material properties.
The selected numerical results were presented to indicate the
influences of nanotube volume fractions and end supports on the
critical axial buckling loads of nanocomposite beams relevant to
long- and short-nanotube composites.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.