Abstract: The fuel cost of the motor vehicle operating on its
common route is an important part of the operating cost. Therefore,
the importance of the fuel saving is increasing day by day. One of the
parameters which improve fuel saving is the regulation of driving
characteristics. The number and duration of stop is increased by the
heavy traffic load. It is possible to improve the fuel saving with
regulation of traffic flow and driving characteristics. The researches
show that the regulation of the traffic flow decreases fuel
consumption, but it is not enough to improve fuel saving without the
regulation of driving characteristics. This study analyses the fuel
consumption of two trips of city bus operating on its common route
and determines the effect of traffic density and driving characteristics
on fuel consumption. Finally it offers some suggestions about
regulation of driving characteristics to improve the fuel saving. Fuel
saving is determined according to the results obtained from
simulation program. When experimental and simulation results are
compared, it has been found that the fuel saving was reached up the
to 40 percent ratios.
Abstract: Gold coated silica core nanoparticles have an optical
response dictated by the plasmon resonance. The wavelength at
which the resonance occurs depends on the core and shell sizes,
allowing nanoshells to be tailored for particular applications. The
purposes of this study was to synthesize and use different
concentration of gold nanoshells as exogenous material for skin
tissue soldering and also to examine the effect of laser soldering
parameters on the properties of repaired skin. Two mixtures of
albumin solder and different concentration of gold nanoshells were
prepared. A full thickness incision of 2×20 mm2 was made on the
surface and after addition of mixtures it was irradiated by an 810nm
diode laser at different power densities. The changes of tensile
strength σt due to temperature rise, number of scan (Ns), and scan
velocity (Vs) were investigated. The results showed at constant laser
power density (I), σt of repaired incisions increases by increasing the
concentration of gold nanoshells, Ns and decreasing Vs. It is therefore
important to consider the trade off between the scan velocity and the
surface temperature for achieving an optimum operating condition. In
our case this corresponds to σt =1610 gr/cm2 at I~ 60 Wcm-2, T ~
65ºC, Ns =10 and Vs=0.2mms-1.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: This paper presents a hybrid approach for solving nqueen problem by combination of PSO and SA. PSO is a population based heuristic method that sometimes traps in local maximum. To solve this problem we can use SA. Although SA suffer from many iterations and long time convergence for solving some problems, By good adjusting initial parameters such as temperature and the length of temperature stages SA guarantees convergence. In this article we use discrete PSO (due to nature of n-queen problem) to achieve a good local maximum. Then we use SA to escape from local maximum. The experimental results show that our hybrid method in comparison of SA method converges to result faster, especially for high dimensions n-queen problems.
Abstract: The shortest path routing problem is a multiobjective
nonlinear optimization problem with constraints. This problem has
been addressed by considering Quality of service parameters, delay
and cost objectives separately or as a weighted sum of both
objectives. Multiobjective evolutionary algorithms can find multiple
pareto-optimal solutions in one single run and this ability makes them
attractive for solving problems with multiple and conflicting
objectives. This paper uses an elitist multiobjective evolutionary
algorithm based on the Non-dominated Sorting Genetic Algorithm
(NSGA), for solving the dynamic shortest path routing problem in
computer networks. A priority-based encoding scheme is proposed
for population initialization. Elitism ensures that the best solution
does not deteriorate in the next generations. Results for a sample test
network have been presented to demonstrate the capabilities of the
proposed approach to generate well-distributed pareto-optimal
solutions of dynamic routing problem in one single run. The results
obtained by NSGA are compared with single objective weighting
factor method for which Genetic Algorithm (GA) was applied.
Abstract: This study has investigated the antidiabetic and
antioxidant potential of Pseudovaria macrophylla bark extract on
streptozotocin–nicotinamide induced type 2 diabetic rats. LCMSQTOF
and NMR experiments were done to determine the chemical
composition in the methanolic bark extract. For in vivo experiments,
the STZ (60 mg/kg/b.w, 15 min after 120 mg/kg/1 nicotinamide, i.p.)
induced diabetic rats were treated with methanolic extract of
Pseuduvaria macrophylla (200 and 400 mg/kg·bw) and
glibenclamide (2.5 mg/kg) as positive control respectively.
Biochemical parameters were assayed in the blood samples of all
groups of rats. The pro-inflammatory cytokines, antioxidant status
and plasma transforming growth factor βeta-1 (TGF-β1) were
evaluated. The histological study of the pancreas was examined and
its expression level of insulin was observed by
immunohistochemistry. In addition, the expression of glucose
transporters (GLUT 1, 2 and 4) were assessed in pancreas tissue by
western blot analysis. The outcomes of the study displayed that the
bark methanol extract of Pseuduvaria macrophylla has potentially
normalized the elevated blood glucose levels and improved serum
insulin and C-peptide levels with significant increase in the
antioxidant enzyme, reduced glutathione (GSH) and decrease in the
level of lipid peroxidation (LPO). Additionally, the extract has
markedly decreased the levels of serum pro-inflammatory cytokines
and transforming growth factor beta-1 (TGF-β1). Histopathology
analysis demonstrated that Pseuduvaria macrophylla has the
potential to protect the pancreas of diabetic rats against peroxidation
damage by downregulating oxidative stress and elevated
hyperglycaemia. Furthermore, the expression of insulin protein,
GLUT-1, GLUT-2 and GLUT-4 in pancreatic cells was enhanced.
The findings of this study support the anti-diabetic claims of
Pseudovaria macrophylla bark.
Abstract: The design of technological procedures for
manufacturing certain products demands the definition and
optimization of technological process parameters. Their
determination depends on the model of the process itself and its
complexity. Certain processes do not have an adequate mathematical
model, thus they are modeled using heuristic methods. First part of
this paper presents a state of the art of using soft computing
techniques in manufacturing processes from the perspective of
applicability in modern CAx systems. Methods of artificial
intelligence which can be used for this purpose are analyzed. The
second part of this paper shows some of the developed models of
certain processes, as well as their applicability in the actual
calculation of parameters of some technological processes within the
design system from the viewpoint of productivity.
Abstract: This paper addresses functional projective lag synchronization of Lorenz system with four unknown parameters, where the output of the master system lags behind the output of the slave system proportionally. For this purpose, an adaptive control law is proposed to make the states of two identical Lorenz systems asymptotically synchronize up. Based on Lyapunov stability theory, a novel criterion is given for asymptotical stability of the null solution of an error dynamics. Finally, some numerical examples are provided to show the effectiveness of our results.
Abstract: One of Effective parameters on the performance of linear induction motors is number of poles which must be selected and optimized to increase power efficiency and motor performance significantly. In this paper a double-sided linear induction motor with different poles number by using MAXWELL3D software is designed and with finite element method is analyzed electromagnetically. Then for dynamic simulation, linear motor by using MATLAB software is simulated. The results show that by adding poles number, system time response is increased and motor after more time reaches to steady state. Also propulsion force of motor is increased.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: Programmable logic controllers are the main controllers in the today's industries; they are used for several applications in industrial control systems and there are lots of examples exist from the PLC applications in industries especially in big companies and plants such as refineries, power plants, petrochemical companies, steel companies, and food and production companies. In the PLCs there are some functions in the function library in software that can be used in PLC programs as basic program elements. The aim of this project are introducing and implementing a new function block of a neural network to the function library of PLC. This block can be applied for some control applications or nonlinear functions calculations after it has been trained for these applications. The implemented neural network is a Perceptron neural network with three layers, three input nodes and one output node. The block can be used in manual or automatic mode. In this paper the structure of the implemented function block, the parameters and the training method of the network are presented by considering the especial method of PLC programming and its complexities. Finally the application of the new block is compared with a classic simulated block and the results are presented.
Abstract: The objective of this study is to introduce estimators to the parameters and survival function for Weibull distribution using three different methods, Maximum Likelihood estimation, Standard Bayes estimation and Modified Bayes estimation. We will then compared the three methods using simulation study to find the best one base on MPE and MSE.
Abstract: In the LFC problem, the interconnections among some areas are the input of disturbances, and therefore, it is important to suppress the disturbances by the coordination of governor systems. In contrast, tie-line power flow control by TCPS located between two areas makes it possible to stabilize the system frequency oscillations positively through interconnection, which is also expected to provide a new ancillary service for the further power systems. Thus, a control strategy using controlling the phase angle of TCPS is proposed for provide active control facility of system frequency in this paper. Also, the optimum adjustment of PID controller's parameters in a robust way under bilateral contracted scenario following the large step load demands and disturbances with and without TCPS are investigated by Particle Swarm Optimization (PSO), that has a strong ability to find the most optimistic results. This newly developed control strategy combines the advantage of PSO and TCPS and has simple stricture that is easy to implement and tune. To demonstrate the effectiveness of the proposed control strategy a three-area restructured power system is considered as a test system under different operating conditions and system nonlinearities. Analysis reveals that the TCPS is quite capable of suppressing the frequency and tie-line power oscillations effectively as compared to that obtained without TCPS for a wide range of plant parameter changes, area load demands and disturbances even in the presence of system nonlinearities.
Abstract: The paper examines the performance of bit-interleaved parity (BIP) methods in error rate monitoring, and in declaration and clearing of alarms in those transport networks that employ automatic protection switching (APS). The BIP-based error rate monitoring is attractive for its simplicity and ease of implementation. The BIP-based results are compared with exact results and are found to declare the alarms too late, and to clear the alarms too early. It is concluded that the standards development and systems implementation should take into account the fact of early clearing and late declaration of alarms. The window parameters defining the detection and clearing thresholds should be set so as to build sufficient hysteresis into the system to ensure that BIP-based implementations yield acceptable performance results.
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: An experiment was conducted to determine the effect
of the rearing system on growth performance, carcass yield,
hematological parameters, and feather pecking damage of Thai
indigenous chickens. Three hundred and sixty 1-d-old chicks were
randomly assigned to 2 treatments: indoor treatment and outdoor
access treatment. In the indoor treatment, the chickens were housed
in floor pens (5 birds/m2). In the outdoor access treatment, the
chickens were housed in a similar indoor house; in addition, they also
had an outdoor grass paddock (1 bird/m2). All birds were provided
with same diet and were raised for 16 wk of age. The results showed
that growth performance and carcass yield were not different among
treatment (P>0.05). Outdoor access had no effect on hematological
parameters (P>0.05). However, the feather pecking damage of the
chickens in the outdoor access treatment was lower than that of the
chickens in the indoor treatment (P
Abstract: Shrunken patterning for integrated device
manufacturing requires surface cleanliness and surface smoothness in
wet chemical processing [1]. It is necessary to control all process
parameters perfectly especially for the common cleaning technique
RCA clean (SC-1 and SC-2) [2]. In this paper the characteristic and
effect of surface preparation parameters are discussed. The properties
of RCA wet chemical processing in silicon technology is based on
processing time, temperature, concentration and megasonic power of
SC-1 and QDR. An improvement of wafer surface preparation by
the enhanced variables of the wet cleaning chemical process is
proposed.
Abstract: A steady two-phase flow model has been developed to simulate the drying process of porous particle in a pneumatic conveying dryer. The model takes into account the momentum, heat and mass transfer between the continuous phase and the dispersed phase. A single particle model was employed to calculate the evaporation rate. In this model the pore structure is simplified to allow the dominant evaporation mechanism to be readily identified at all points within the duct. The predominant mechanism at any time depends upon the pressure, temperature and the diameter of pore from which evaporating is occurring. The model was validated against experimental studies of pneumatic transport at low and high speeds as well as pneumatic drying. The effects of operating conditions on the dryer parameters are studied numerically. The present results show that the drying rate is enhanced as the inlet gas temperature and the gas flow rate increase and as the solid mass flow rate deceases. The present results also demonstrate the necessity of measuring the inlet gas velocity or the solid concentration in any experimental analysis.