Abstract: Continuously growing needs for Internet applications
that transmit massive amount of data have led to the emergence of
high speed network. Data transfer must take place without any
congestion and hence feedback parameters must be transferred from
the receiver end to the sender end so as to restrict the sending rate in
order to avoid congestion. Even though TCP tries to avoid
congestion by restricting the sending rate and window size, it never
announces the sender about the capacity of the data to be sent and
also it reduces the window size by half at the time of congestion
therefore resulting in the decrease of throughput, low utilization of
the bandwidth and maximum delay. In this paper, XCP protocol is
used and feedback parameters are calculated based on arrival rate,
service rate, traffic rate and queue size and hence the receiver
informs the sender about the throughput, capacity of the data to be
sent and window size adjustment, resulting in no drastic decrease in
window size, better increase in sending rate because of which there is
a continuous flow of data without congestion. Therefore as a result of
this, there is a maximum increase in throughput, high utilization of
the bandwidth and minimum delay. The result of the proposed work
is presented as a graph based on throughput, delay and window size.
Thus in this paper, XCP protocol is well illustrated and the various
parameters are thoroughly analyzed and adequately presented.
Abstract: Current mode circuits like current conveyors are
getting significant attention in current analog ICs design due to their
higher band-width, greater linearity, larger dynamic range, simpler
circuitry, lower power consumption and less chip area. The second
generation current controlled conveyor (CCCII) has the advantage of
electronic adjustability over the CCII i.e. in CCCII; adjustment of the
X-terminal intrinsic resistance via a bias current is possible. The
presented approach is based on the CMOS implementation of second
generation positive (CCCII+), negative (CCCII-) and dual Output
Current Controlled Conveyor (DOCCCII) and its application as
Universal filter. All the circuits have been designed and simulated
using 65nm CMOS technology model parameters on Cadence
Virtuoso / Spectre using 1V supply voltage. Various simulations have
been carried out to verify the linearity between output and input
ports, range of operation frequency, etc. The outcomes show good
agreement between expected and experimental results.
Abstract: Genetic Algorithms (GAs) are direct searching
methods which require little information from design space. This
characteristic beside robustness of these algorithms makes them to be
very popular in recent decades. On the other hand, while this method
is employed, there is no guarantee to achieve optimum results. This
obliged designer to run such algorithms more than one time to
achieve more reliable results. There are many attempts to modify the
algorithms to make them more efficient. In this paper, by application
of fractal dimension (particularly, Box Counting Method), the
complexity of design space are established for determination of
mutation and crossover probabilities (Pm and Pc). This methodology
is followed by a numerical example for more clarification. It is
concluded that this modification will improve efficiency of GAs and
make them to bring about more reliable results especially for design
space with higher fractal dimensions.
Abstract: This research is to design and implement a new kind
of agitators called differential agitator. The Differential Agitator is an
electro- mechanic set consists of two shafts. The first shaft is the
bearing axis while the second shaft is the axis of the quartet upper
bearing impellers group and the triple lower group which are called
as agitating group. The agitating group is located inside a cylindrical
container equipped especially to contain square directors for the
liquid entrance and square directors called fixing group for the liquid
exit. The fixing group is installed containing the agitating group
inside any tank whether from upper or lower position. The agitating
process occurs through the agitating group bearing causing a lower
pressure over the upper group leading to withdrawing the liquid from
the square directors of the liquid entering and consequently the liquid
moves to the denser place under the quartet upper group. Then, the
liquid moves to the so high pressure area under the agitating group
causing the liquid to exit from the square directors in the bottom of
the container. For improving efficiency, parametric study and shape
optimization has been carried out. A numerical analysis,
manufacturing and laboratory experiments were conducted to design
and implement the differential agitator. Knowing the material
prosperities and the loading conditions, the FEM using ANSYS11
was used to get the optimum design of the geometrical parameters of
the differential agitator elements while the experimental test was
performed to validate the advantages of the differential agitators to
give a high agitation performance of lime in the water as an example.
In addition, the experimental work has been done to express the
internal container shape in the agitation efficiency. The study ended
up with conclusions to maximize agitator performance and optimize
the geometrical parameters to be used for manufacturing the
differential agitator
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: The objective of the present study was to examine the
dose-response relationships between antioxidant parameters and liver
contaminant levels of Kazakhstan light crude oil (KLCO) in albino
rats. The animals were repeatedly exposed, by intraperitoneal
injection, to low dosages (0.5–1.5 ml/kg) of KLCO. Rats exposed to
these doses levels did not show any apparent symptoms of
intoxication. Serum aminotransferases increased significantly
(p
Abstract: Full - Scale Accelerated Loading System, one part of
“the Eleventh - Five - Year National Grand Technology Infrastructure
Program" is a facility to evaluate the performance and service life of
different kinds of pavements subjected to traffic loading under full -
controlled environment. While simulating the environments of frigid
zone and permafrost zone, the accurate control of air temperature, road
temperature and roadbed temperature are the key points and also
aporias for the designment. In this paper, numerical simulations are
used to determine the design parameters of the frozen soil simulation
system. At first, a brief introduction of the Full - Scale Accelerate
Loading System was given. Then, the temperature control method of
frozen soil simulation system was proposed. Finally, by using finite
element simulations, the optimal design of frozen soil simulation
system was obtained. This proposed design, which was obtained by
finite element simulations, provided significant referents to the
ultimate design of the environment simulation system.
Abstract: In recent years, there has been an increasing interest in using daylight to save energy in buildings. In tropical regions, daylighting is always an energy saver. On the other hand, daylight provides visual comfort. According to standards, it shows that many criteria should be taken into consideration in order to have daylight utilization and visual comfort. The current standard in Malaysia, MS 1525 does not provide sufficient guideline. Hence, more research is needed on daylight performance. If architects do not consider daylight design, it not only causes inconvenience in working spaces but also causes more energy consumption as well as environmental pollution. This research had surveyed daylight performance in 5 selected office buildings from different area of Malaysian through experimental method. Several parameters of daylight quality such as daylight factor, surface luminance and surface luminance ratio were measured in different rooms in each building. The result of this research demonstrated that most of the buildings were not designed for daylight utilization. Therefore, it is very important that architects follow the daylight design recommendation to reduce consumption of electric power for artificial lighting while the sufficient quality of daylight is available.
Abstract: In inspection and workpiece localization, sampling point data is an important issue. Since the devices for sampling only sample discrete points, not the completely surface, sampling size and location of the points will be taken into consideration. In this paper a method is presented for determining the sampled points size and location for achieving efficient sampling. Firstly, uncertainty analysis of the localization parameters is investigated. A localization uncertainty model is developed to predict the uncertainty of the localization process. Using this model the minimum size of the sampled points is predicted. Secondly, based on the algebra theory an eigenvalue-optimal optimization is proposed. Then a freeform surface is used in the simulation. The proposed optimization is implemented. The simulation result shows its effectivity.
Abstract: Nonlinear finite element method and Serendipity eight
nodes element are used for determining of ground surface settlement
due to tunneling. Linear element with elastic behavior is used for
modeling of lining. Modified Generalized plasticity model with nonassociated
flow rule is applied for analysis of a tunnel in Sao Paulo –
Brazil. The tunnel had analyzed by Lades- model with 16 parameters.
In this work modified Generalized Plasticity is used with 10
parameters, also Mohr-Coulomb model is used to analysis the tunnel.
The results show good agreement with observed results of field data
by modified Generalized Plasticity model than other models. The
obtained result by Mohr-Coulomb model shows less settlement than
other model due to excavation.
Abstract: Development of intelligent assembly cell conception includes new solution kind of how to create structures of automated and flexible assembly system. The current trend of the final product quality increasing is affected by time analysis of the entire manufacturing process. The primary requirement of manufacturing is to produce as many products as soon as possible, at the lowest possible cost, but of course with the highest quality. Such requirements may be satisfied only if all the elements entering and affecting the production cycle are in a fully functional condition. These elements consist of sensory equipment and intelligent control elements that are essential for building intelligent manufacturing systems. Intelligent behavior of the system as the control system will repose on monitoring of important parameters of the system in the real time. Intelligent manufacturing system itself should be a system that can flexibly respond to changes in entering and exiting the process in interaction with the surroundings.
Abstract: Ionic liquids are well known as green solvents, reaction media and catalysis. Here, three different sulfonic acid functional ionic liquids prepared in the laboratory are used as catalysts in alkylation of p-cresol with tert-butyl alcohol. The kinetics on each of the catalysts was compared and a kinetic model was developed based on the product distribution over these catalysts. The kinetic parameters were estimated using Marquadt's algorithm to minimize the error function. The Arrhenius plots show a curvature which is best interpreted by the extended Arrhenius equation.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: Multi criteria decision analysis (MDCA) covers both
data and experience. It is very common to solve the problems with
many parameters and uncertainties. GIS supported solutions improve
and speed up the decision process. Weighted grading as a MDCA
method is employed for solving the geotechnical problems. In this
study, geotechnical parameters namely soil type; SPT (N) blow
number, shear wave velocity (Vs) and depth of underground water
level (DUWL) have been engaged in MDCA and GIS. In terms of
geotechnical aspects, the settlement suitability of the municipal area
was analyzed by the method. MDCA results were compatible with
the geotechnical observations and experience. The method can be
employed in geotechnical oriented microzoning studies if the criteria
are well evaluated.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: Evolvable hardware (EHW) refers to a selfreconfiguration
hardware design, where the configuration is under
the control of an evolutionary algorithm (EA). A lot of research has
been done in this area several different EA have been introduced.
Every time a specific EA is chosen for solving a particular problem,
all its components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade a lot of
research has been carried out in order to identify the best parameters
for the EA-s components for different “test-problems". However
different researchers propose different solutions. In this paper the
behaviour of mutation rate on (1+λ) evolution strategy (ES) for
designing logic circuits, which has not been done before, has been
deeply analyzed. The mutation rate for an EHW system modifies
values of the logic cell inputs, the cell type (for example from AND
to NOR) and the circuit output. The behaviour of the mutation has
been analyzed based on the number of generations, genotype
redundancy and number of logic gates used for the evolved circuits.
The experimental results found provide the behaviour of the mutation
rate to be used during evolution for the design and optimization of
logic circuits. The researches on the best mutation rate during the last
40 years are also summarized.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: Our results showed that treatment with both
cyclooxygenase (COX1 or COX2) inhibitors impair reproduction
parameters of the medaka. Resveratrol (COX1 inhibitor) caused an
decrease in the number of spawning females at the first week of
feeding fish with experimental diets. In the group treated with NS-
398 (COX2 inhibitor) we found the lowest sperm velocity parameters
and decreased linearity of movement. The ovaries of the medaka fed
feed supplemented with Resveratrol or NS-398 were confirmed to
have a lower share of matured oocytes however during the
experiment (four weeks) the number of eggs spawned by females was
similar. Both inhibitors in fish diet (20 mg/kg body weight/day)
caused a decrease in the embryo survival. Our results revealed that
for the medaka female reproduction, activity of both COX enzymes
might be necessary whereas males reproduction competence, as
expressed by sperm motility parameters, might be related to COX2
activity.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A number of studies have reported increased cardiometabolic risk, premature ardiovascular disease and incidence of type 2 diabetes. Rugby union players have somatotypes very similar
to National Football league players which suggest that rugby players may have similar health risks. The International Golden Oldies World Rugby Festival (GORF) provided a
unique opportunity to investigate the demographics of veteran rugby players. METHODOLOGIES: A cross-sectional, observational study was completed using an online web-based
questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one sample t-test (50yrs) and Chi-square test. RESULTS: A total of 216 veteran rugby competitors
(response rate = 6.8%) representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0), participated in the online survey. As a group, the incidence of current smokers was low at 8.8%
(avg 72.4 cigs/wk) whilst the percentage consuming alcohol
was high (93.1% (avg 11.2 drinks/wk). Competitors reported
the following top six chronic diseases/disorders; hypertension
(18.6%), arthritis (OA/RA, 11.5%), asthma (9.3%),
hyperlipidemia (8.2%), diabetes (all types, 7.5%) and gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to
the Australian general population (Australian Bureau of Statistics data, n=18,000), GORF competitors had a
Climstein Mike, Walsh Joe (corresponding author) and Burke Stephen
School of Exercise Science, Australian Catholic University, 25A Barker Road,
Strathfield, Sydney, NSW, 2016, Australia (e-mail:
[email protected], [email protected],
[email protected]).
John Best is with Orthosports, 160 Belmore Rd., Randwick, Sydney,NSW
2031, Australia (e-mail: [email protected]).
Heazlewood, Ian Timothy is with School of Environmental and Life
Sciences, Faculty Education, Health and Science, Charles Darwin University,
Precinct Yellow Building 2, Charles Darwin University, NT 0909, Australia
(e-mail: [email protected]).
Kettunen Jyrki Arcada University of Applied Sciences, Jan-Magnus
Janssonin aukio 1, FI-00550, Helsinki, Finland (e-mail:
[email protected]).
Adams Kent is with California State University Monterey Bay, Kinesiology Department, 100 Campus Center, Seaside, CA., 93955, USA (email: [email protected]).
DeBeliso Mark is with Department of Physical Education and Human
Performance, Southern Utah University, 351 West University Blvd, Cedar
City, Utah, USA (e-mail: [email protected]).
significantly lower incidence of anxiety (p