Abstract: A self-compacting concrete (SCC) is the one that can
be placed in the form and can go through obstructions by its own
weight and without the need of vibration. Since its first development
in Japan in 1988, SCC has gained wider acceptance in Japan, Europe
and USA due to its inherent distinct advantages. Although there are
visible signs of its gradual acceptance in the North Africa through its
limited use in construction, Libya has yet to explore the feasibility
and applicability of SCC in new construction. The contributing
factors to this reluctance appear to be lack of any supportive
evidence of its suitability with local aggregates and the harsh
environmental conditions. The primary aim of this study is to explore
the feasibility of using SCC made with local aggregates of Eastern
Province of Libya by examining its basic properties characteristics.
This research consists of: (i) Development of a suitable mix for SCC
such as the effect of water to cement ratio, limestone and silica fume
that would satisfy the requirements of the plastic state; (ii) Casting of
concrete samples and testing them for compressive strength and unit
weight. Local aggregates, cement, admixtures and industrial waste
materials were used in this research.
The significance of this research lies in its attempt to provide
some performance data of SCC made in the Eastern Province of
Libya so as to draw attention to the possible use of SCC.
Abstract: In this paper, the wear of high speed steel hobs during
hobbing has been studied. The wear mechanisms are strongly
influenced by the choice of cutting speed. At moderate and high
cutting speeds three major wear mechanisms were identified:
abrasion, mild adhesive and severe adhesive. The microstructure and
wear behavior of two high speed steel grades (M2 and ASP30) has
been compared. In contrast, a variation in chemical composition or
microstructure of HSS tool material generally did not change the
dominant wear mechanism. However, the tool material properties
determine the resistance against the operating wear mechanism and
consequently the tool life. The metallographic analysis and wear
measurement at the tip of hob teeth included scanning electron
microscopy and stereoscope microscopy. Roughness profilometery is
used for measuring the gear surface roughness.
Abstract: These days MANET is attracting much attention as
they are expected to gratefully influence communication between
wireless nodes. Along with this great strength, there is much more
chance of leave and being attacked by a malicious node. Due to this
reason much attention is given to the security and the private issue in
MANET. A lot of research in MANET has been doing. In this paper
we present the overview of MANET, the security issues of MANET,
IP configuration in MANET, the solution to puzzle out the security
issues and the simulation of the proposal idea. We add the method to
figure out the malicious nodes so that we can prevent the attack from
them. Nodes exchange the information about nodes to prevent DAD
attack. We can get 30% better performance than the previous
MANETConf.
Abstract: The aerodynamic performances of vertical axis wind
turbines are highly affected by tip vortexes. In the present
work, different tip devices are considered and simulated against
a baseline rotor configuration, with the aim of identifying the
best tip architecture. Three different configurations are tested:
winglets, an elliptic termination and an aerodynamic bulkhead.
A comparative analysis on the most promising architectures is
conducted, focusing also on blade torque evolution during a full
revolution of the rotor blade. The most promising technology is
concluded to be a well designed winglet.
Abstract: Fuzzy sets theory affirmed that the linguistic value for
every contraries relation is complementary. It was stressed in the
intuitionistic fuzzy sets (IFS) that the conditions for contraries
relations, which are the fuzzy values, cannot be greater than one.
However, complementary in two contradict phenomena are not
always true. This paper proposes a new idea condition for conflicting
bifuzzy sets by relaxing the condition of intuitionistic fuzzy sets.
Here, we will critically forward examples using triangular fuzzy
number in formulating a new condition for conflicting bifuzzy sets
(CBFS). Evaluation of positive and negative in conflicting
phenomena were calculated concurrently by relaxing the condition in
IFS. The hypothetical illustration showed the applicability of the new
condition in CBFS for solving non-complement contraries
intuitionistic evaluation. This approach can be applied to any
decision making where conflicting is very much exist.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: Steroidal hormones with the efficient changes on the epiphyseal growth plate may influence tissue structure properties. Presents paper to investigate the effects of gonadectomy in the pattern distribution of the epiphyseal structure. Fifteen adult female New Zealand white rabbits were separated into three groups. One group was intact and others groups were selected for surgical operation. From these two groups, one group carried out steroidal administration. The results obtained showed that there is no statistically difference in the mean diameter of the growth plate cells between all three groups. The maximum value of the cartilage cells were allocated to the gonadectomized group and the minimum number were observed in Hormonal induced group significantly. Growth plate height was significantly greater in gonadectomized group than in two other groups.
Abstract: The possibility of producing drinking water from
brackish ground water using Vacuum membrane distillation (VMD)
process was studied. It is a rising technology for seawater or brine
desalination process. The process simply consists of a flat sheet
hydrophobic micro porous PTFE membrane and diaphragm vacuum
pump without a condenser for the water recovery or trap. In this
work, VMD performance was investigated for aqueous NaCl solution
and natural ground water. The influence of operational parameters
such as feed flow rate (30 to 55 l/h), feed temperature (313 to 333 K),
feed salt concentration (5000 to 7000 mg/l) and permeate pressure
(1.5 to 6 kPa) on the membrane distillation (MD) permeation flux
have been investigated. The maximum flux reached to 28.34 kg/m2 h
at feed temperature, 333 K; vacuum pressure, 1.5 kPa; feed flow rate,
55 l/h and feed salt concentration, 7000 mg/l. The negligible effects
in the reduction of permeate flux found over 150 h experimental run
for salt water. But for the natural ground water application over 75 h,
scale deposits observed on the membrane surface and 29% reduction
in the permeate flux over 75 h. This reduction can be eliminated by
acidification of feed water. Hence, promote the research attention in
apply of VMD for the ground water purification over today-s
conventional RO operation.
Abstract: Silk sericin (SS) is a glue-like protein from silkworm
cocoon. With its outstanding moisturization and activation collagen
synthesis properties, silk protein is applied for wound healing. Since
wound dressing in film preparation can facilitate patients-
convenience and reduce risk of wound contraction, SS and polyvinyl
alcohol (PVA) films were prepared with various concentrations of
SS. Their physical properties such as surface density, light
transmission, protein dissolution and tensile modulus were
investigated. The results presented that 3% SS with 2% PVA is the
best ingredient for SS film forming.
Abstract: Indices summarizing community structure are used to
evaluate fundamental community ecology, species interaction,
biogeographical factors, and environmental stress. Some of these
indices are insensitive to gross community changes induced by
contaminants of pollution. Diversity indices and similarity indices are
reviewed considering their ecological application, both theoretical
and practical. For some useful indices, empirical equations are given
to calculate the expected maximum value of the indices to which the
observed values can be related at any combination of sample sizes at
the experimental sites. This paper examines the effects of sample size
and diversity on the expected values of diversity indices and
similarity indices, using various formulae. It has been shown that all
indices are strongly affected by sample size and diversity. In some
indices, this influence is greater than the others and an attempt has
been made to deal with these influences.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: In order to explore the relationship of promotion activities, destination attribute and destination image of Vietnam and find possible solutions, this study uses decision system analysis (DSA) method to develop flowcharts based on three rounds of expert interviews. The interviews were conducted with the experts who were confirmed to directly participate or influence on the decision making that drives the promotion of Vietnam tourism process. This study identifies three models and describes specific decisions on promotion activities, destination attributes and destination images. This study finally derives a general model for promoting the Tourism Industrial Service Network (TISN) in Vietnam. This study finds that the coordination with all sectors and industries of tourism to facilitate favorable condition and improving destination attributes in linking with the efficient promotion activities is highly recommended in order to make visitors satisfied and improve the destination image.
Abstract: Automatic determination of blood in less bright or
noisy capsule endoscopic images is difficult due to low S/N ratio.
Especially it may not be accurate to analyze these images due to the
influence of external disturbance. Therefore, we proposed detection
methods that are not dependent only on color bands. In locating
bleeding regions, the identification of object outlines in the frame and
features of their local colors were taken into consideration. The results
showed that the capability of detecting bleeding was much improved.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: This article presents a numerical study of the doublediffusive
mixed convection in a vertical channel filled with porous
medium by using non-equilibrium model. The flow is assumed
fully developed, uni-directional and steady state. The controlling
parameters are thermal Rayleigh number (RaT ), Darcy number (Da),
Forchheimer number (F), buoyancy ratio (N), inter phase heat transfer
coefficient (H), and porosity scaled thermal conductivity ratio
(γ). The Brinkman-extended non-Darcy model is considered. The
governing equations are solved by spectral collocation method. The
main emphasize is given on flow profiles as well as heat and solute
transfer rates, when two diffusive components in terms of buoyancy
ratio are in favor (against) of each other and solid matrix and fluid
are thermally non-equilibrium. The results show that, for aiding flow
(RaT = 1000), the heat transfer rate of fluid (Nuf ) increases upto a
certain value of H, beyond that decreases smoothly and converges
to a constant, whereas in case of opposing flow (RaT = -1000),
the result is same for N = 0 and 1. The variation of Nuf in (N,
Nuf )-plane shows sinusoidal pattern for RaT = -1000. For both cases
(aiding and opposing) the flow destabilize on increasing N by inviting
point of inflection or flow separation on the velocity profile. Overall,
the buoyancy force have significant impact on the non-Darcy mixed
convection under LTNE conditions.
Abstract: This study investigated the climatic factors associated
with Influenza incidence in Nakhon Si Thammarat, Southern
Thailand. Climatic factors comprised of the amount of rainfall,
percent of rainy days, relative humidity, wind speed, maximum,
minimum temperatures and temperature difference. A multiple
stepwise regression technique was used to fit the statistical model.
The result showed that the temperature difference and percent of
rainy days were positively associated with Influenza incidence in
Nakhon Si Thammarat.
Abstract: In line with changes of consumers modern lifestyle has call for the advertising strategy to change. This research is to find out how game with telepresence and product experience embedded in the computer game to affect users- intention to purchase. Game content developers are urging to consider of placing product message as part of game design strategy that can influence the game player-s intention to purchase. Experiment was carried out on two hundred and fifty undergraduate students who volunteered to participate in the Internet game playing activities. A factor analysis and correlation analysis was performed on items designed to measure telepresence, attitudes toward telepresence, and game player intention to purchase the product advertise in the game that respondents experienced. The results indicated that telepresence consist of interactive experience and product experience. The study also found that product experience is positively related to the game players- intention to purchase. The significance of product experience implies the usefulness of an interactive advertising in the game playing to attract players- intention to purchase the advertised product placed in the creative game design.
Abstract: In this paper multi-objective genetic algorithms are
employed for Pareto approach optimization of ideal Turboshaft
engines. In the multi-objective optimization a number of conflicting
objective functions are to be optimized simultaneously. The
important objective functions that have been considered for
optimization are specific thrust (F/m& 0), specific fuel consumption
( P S ), output shaft power 0 (& /&) shaft W m and overall efficiency( ) O
η .
These objectives are usually conflicting with each other. The design
variables consist of thermodynamic parameters (compressor pressure
ratio, turbine temperature ratio and Mach number).
At the first stage single objective optimization has been
investigated and the method of NSGA-II has been used for multiobjective
optimization. Optimization procedures are performed for
two and four objective functions and the results are compared for
ideal Turboshaft engine. In order to investigate the optimal
thermodynamic behavior of two objectives, different set, each
including two objectives of output parameters, are considered
individually. For each set Pareto front are depicted. The sets of
selected decision variables based on this Pareto front, will cause the
best possible combination of corresponding objective functions.
There is no superiority for the points on the Pareto front figure,
but they are superior to any other point. In the case of four objective
optimization the results are given in tables.
Abstract: The purpose of this study was to determine the
influence of physical activity and dietary fat intake on Body Mass
Index (BMI) of lecturers within a higher learning institutionalized
setting. The study adopted a Cross-sectional Correlational Design
and included 120 lecturers selected proportionately by simple
random sampling techniques from a population of 600 lecturers. Data
was collected using questionnaires, which had sections including
physical activity checklist adopted from the international physical
activity questionnaire (IPAQ), 24-hour food recall, anthropometric
measurements mainly weight and height. Analysis involved the use
of bivariate correlations and linear regression. A significant inverse
association was registered between BMI and duration (in minutes)
spent doing moderate intense physical activity per day (r=-0.322,
p
Abstract: The influence of extrusion parameters on surface
quality and properties of AA6061+x% vol. SiC (x = 0; 2,5; 5; 7,5;10)
composites was discussed in this paper. The averages size of
AA6061 and SiC particles were 10.6 μm and 0.42 μm, respectively.
Two series of composites (I - compacts were preheated at extrusion
temperature through 0.5 h and cooled by water directly after process;
II - compacts were preheated through 3 hours and were not cooled)
were consolidated via powder metallurgy processing and extruded by
KoBo method. High values of density for both series of composites
were achieved. Better surface quality was observed for II series of
composites. Moreover, for these composites lower (compared to I
series) but more uniform strength properties over the cross-section of
the bar were noticed. Microstructure and Young-s modulus
investigations were made.