Abstract: In this work, we demonstrated vertical RRAM device fabricated at the sidewall of contact hole structures for possible future 3-D stacking integrations. The fabricated devices exhibit polarity dependent bipolar resistive switching with small operation voltage of less than 1V for both set and reset process. A good retention of memory window ~50 times is maintained after 1000s voltage bias.
Abstract: Silicon photonics has generated an increasing interest in recent years mainly for optical communications optical interconnects in microelectronic circuits or bio-sensing applications. The development of elementary passive and active components (including detectors and modulators), which are mainly fabricated on the silicon on insulator platform for CMOS-compatible fabrication, has reached such a performance level that the integration challenge of silicon photonics with microelectronic circuits should be addressed. Since crystalline silicon can only be grown from another silicon crystal, making it impossible to deposit in this state, the optical devices are typically limited to a single layer. An alternative approach is to integrate a photonic layer above the CMOS chip using back-end CMOS fabrication process. In this paper, various materials, including silicon nitride, amorphous silicon, and polycrystalline silicon, for this purpose are addressed.
Abstract: Silicon photonics is merging as a unified platform for driving photonic based telecommunications and for local photonic based interconnect but it suffers from large footprint as compared with the nanoelectronics. Plasmonics is an attractive alternative for nanophotonics. In this work, two CMOS compatible plasmonic waveguide platforms are compared. One is the horizontal metal-insulator-Si-insulator-metal nanoplasmonic waveguide and the other is metal-insulator-Si hybrid plasmonic waveguide. Various passive and active photonic devices have been experimentally demonstrated based on these two plasmonic waveguide platforms.
Abstract: According to biodiesel from microalgae is an attractive fuel for several reasons such as renewable, biodegradable and environmental friendly. Thus, this study, green microalgae Scenedesmus acutus PPNK1 isolated from natural water, was selected based on high growth rates, easy cultivation and high lipid content. The Nile red fluorescence method has been successfully applied to the determination of lipids in S. acutus PPNK1. The combination of the method to the lipid composition in algal cells showed the yellow fluorescence under fluorescent microscope. Interestingly, maximum cell numbers and biomass concentration were obtained at 5.44´107 cells/mL and 1.60 g/L when it was cultivated in BG-11 medium while in case of BG-11 with nitrogen deprivation (N 0.25 g/L), accumulated lipid content in cells (44.67%) was achieved that was higher than that found in case of BG-11 medium at about 2 times (22.63%).
Abstract: The topological distance between a pair of vertices i and j, which is denoted by d(vi, vj), is the number of edges of the shortest path joining i and j. The Wiener index W(G) is the sum of distances between all pairs of vertices of a graph G. W(G) = i
Abstract: According to synthetic plastics obtained from petroleum cause some environmental problems. Therefore, degradable plastics become widely used and studied for replacing the synthetic plastic waste. A biopolymer of poly hydroxybutyrate-co-hydroxyvalerate (PHBV) is subgroups of a main kind of polyhydroxyalkanoates (PHAs). Naturally, PHBV is hard, brittle and low flexible while natural rubber (NR) is high elastic latex. Then, they are blended and the biodegradation of the blended PHBV and NR films were examined in soil environment. The results showed that the degradation occurs predominantly in the bulk of the samples. The order of biodegradability was shown as follows: PHBV> PHBV/NR> NR. After biodegradation, the blended films were characterized by appearance analysis such as Scanning Electron Microscope (SEM), Fourier transform infrared spectroscopy (FTIR) and Differential Scanning Calorimetry (DSC). It was found that the biodegradation mainly occurred at the polymer surface.
Abstract: In this paper, a low-power digital controller for DC-DC power conversion was presented. The controller generates the pulse-width modulated (PWM) signal from digital inputs provided by analog-to-digital converter (ADC). An efficient and simple design scheme to develop the control unit was discussed. This method allows minimization of the consumed resources of the chip and it is based on direct digital design approach. In this application, with the proposed scheme, nearly half area and two-third of the power consumption was saved compared to the conventional schemes. This work illustrates the possibility of implementing low-power and area-efficient power management circuit using direct digital design based approach.
Abstract: Encouraging physical activity amongst children and adolescents is becoming an increasingly relevant issue in modern society. Studies have shown that involving children and adolescents in physical activity is essential for their physical, mental and social development. However, with technology playing an increasingly important role in reducing physical work it is becoming more critical to incorporate adequate physical activities into our lives. One way to overcome this problem is to harness technology so that it promotes physical activities, for example, by motivating children and adolescents to exercise more. This paper describes a promising solution to the question of how to increase levels of physical activity in children and adolescents by combining gaming technologies with exercise tracking goals. This research describes a framework called FITTER (Framework for Integrating activity Tracking Technologies for Electronic Recreation) that combines video game play with more traditional, non-computer physical activities.
Abstract: This paper presents the design and implementation of a fully integrated Capacitance-to-Voltage Converter (CVC) as the analog front-end for magnetometer interface IC. The application demands very low power solution operating in the frequency of around 20 KHz. The design adapts low power architecture to create low noise electronic interface for Capacitive Micro-machined Lorentz force magnetometer sensor. Using a 0.18-μm CMOS process, simulation results of this interface IC show that the proposed CVC can provide 33 dB closed loop gain, 20 nV/√Hz input referred noise at 20 KHz, while consuming 65 μA current from 1.8-V supply.
Abstract: Force sensor has been used as requisite for knowing information on the amount and the directions of forces on the skin surface. We have developed a four-degrees-of-freedom capacitive force sensor (approximately 20×20×5 mm3) that has a flexible structure and sixteen parallel plate capacitors. An iterative algorithm was developed for estimating four displacements from the sixteen capacitances using fourth-order polynomial approximation of characteristics between capacitance and displacement. The estimation results from measured capacitances had large error caused by deterioration of the characteristics. In this study, effective capacitors had major information were selected on the basis of the capacitance change range and the characteristic shape. Maximum errors in calibration and non-calibration points were 25%and 6.8%.However the maximum error was larger than desired value, the smallness of averaged value indicated the occurrence of a few large error points. On the other hand, error in non-calibration point was within desired value.
Abstract: The purpose of the research is to investigate the energetic feature of the backpack load on soldier’s gait with variation of the trunk flexion angle. It is believed that the trunk flexion variation of the loaded gait may cause a significant difference in the energy cost which is often in practice in daily life. To this end, seven healthy Korea military personnel participated in the experiment and are tested under three different walking postures comprised of the small, natural and large trunk flexion. There are around 5 degree differences of waist angle between each trunk flexion. The ground reaction forces were collected from the force plates and motion kinematic data are measured by the motion capture system. Based on these data, the impulses, momentums and mechanical works done on the center of body mass (COM) during the double support phase were computed. The result shows that the push-off and heel strike impulse are not relevant to the trunk flexion change, however the mechanical work by the push-off and heel strike were changed by the trunk flexion variation. It is because the vertical velocity of the COM during the double support phase is increased significantly with an increase in the trunk flexion. Therefore, we can know that the gait efficiency of the loaded gait depends on the trunk flexion angle. Also, even though the gravitational impulse and pre-collision momentum are changed by the trunk flexion variation, the after-collision momentum is almost constant regardless of the trunk flexion variation.
Abstract: The industrial automation is dependent upon pneumatic control systems. The industrial units are now controlled with digital control systems to tackle the process variables like Temperature, Pressure, Flow rates and Composition.
This research work produces an evaluation of the response time fluctuations for proportional mode, proportional integral and proportional integral derivative modes of automated chemical process control. The controller output is measured for different values of gain with respect to time in three modes (P, PI and PID). In case of P-mode for different values of gain the controller output has negligible change. When the controller output of PI-mode is checked for constant gain, it can be seen that by decreasing the integral time the controller output has showed more fluctuations. The PID mode results have found to be more interesting in a way that when rate minute has changed, the controller output has also showed fluctuations with respect to time. The controller output for integral mode and derivative mode are observed with lesser steady state error, minimum offset and larger response time to control the process variable. The tuning parameters in case of P-mode are only steady state gain with greater errors with respect to controller output. The integral mode showed controller outputs with intermediate responses during integral gain (ki). By increasing the rate minute the derivative gain (kd) also increased which showed the controlled oscillations in case of PID mode and lesser overshoot.
Abstract: This paper discusses E-government, in particular the challenges that face its development and widespread adoption in Saudi Arabia. E-government can be defined based on an existing set of requirements. E-government has been implemented for a considerable time in developed countries. However, E-government services still face many challenges in their implementation and general adoption in Saudi Arabia. In addition, the literature review and the discussion identify the influential factors, such as quality of service, diffusion of innovation, computer and information literacy, culture, lack of awareness, technical infrastructure, website design, and security, that affect the citizens’ intention to adopt E-government services in Saudi Arabia. Consequently, these factors have been integrated in a new model that would influence citizen to adopt E- government services. Therefore, this research presents an integrated model for ascertaining the intention to adopt E-government services and thereby aiding governments in accessing what is required to increase adoption.
Abstract: This paper addresses the analysis of the interference between complementary ground component (CGC) base station and mobile earth station (MES). In the frequency sharing scenario between CGC base station and MES, the interference from the adjacent beams must be considered. In this paper, we estimated the interference to MES of an integrated satellite system and the result is presented as the carrier to interference ratio(C/I) with respect to the number of CGC base station in the adjacent beam and the ratio of satellite beam center radius to the total beam radius (R1/R). By using these results, we can determine the minimum separation distance between the CGC base stations of adjacent beam and MES for compatibility. This result can be applied to the CGC base station of an integrated satellite system for the effective frequency sharing.
Abstract: This study presents a new method for detecting the
cutting tool wear based on the measured cutting force signals using
the regression model and I-kaz method. The detection of tool wear
was done automatically using the in-house developed regression
model and 3D graphic presentation of I-kaz 3D coefficient during
machining process. The machining tests were carried out on a CNC
turning machine Colchester Master Tornado T4 in dry cutting
condition, and Kistler 9255B dynamometer was used to measure the
cutting force signals, which then stored and displayed in the DasyLab
software. The progression of the cutting tool flank wear land (VB)
was indicated by the amount of the cutting force generated. Later, the
I-kaz was used to analyze all the cutting force signals from beginning
of the cut until the rejection stage of the cutting tool. Results of the IKaz
analysis were represented by various characteristic of I-kaz 3D
coefficient and 3D graphic presentation. The I-kaz 3D coefficient
number decreases when the tool wear increases. This method can be
used for real time tool wear monitoring.
Abstract: The electrical power systems of aircrafts have made
serious progress in recent years because the aircrafts depend more
and more on the electricity. There is a trend in the aircraft industry to
replace hydraulic and pneumatic systems with electrical systems,
achieving more comfort and monitoring features and enlarging the
energetic efficiency. Thus, was born the concept More Electric
Aircraft. In this paper is analyzed the integration of a fuel cell into
the existing electrical generation and distribution systems of an
aircraft. The dynamic characteristics of fuel cell systems necessitate
an adaptation of the electrical power system. The architecture studied
in this paper consists of a 50kW fuel cell, a dc to dc converter and
several loads. The dc to dc converter is used to step down the fuel
cell voltage from about 625Vdc to 28Vdc.
Abstract: Purpose: To compare attitudes and perceptions of
Israeli native born mothers versus former Soviet Union (FSU)
immigrant mothers regarding the physical health of their infant.
Methodology: cross-sectional design. A convenience sample of 50
participants was recruited by face to face and snowball technique. A
questionnaire was constructed according to the instructions of the
Ministry of Health for the care and treatment of infants. The main
areas explored were: sources of knowledge that the young mother
acquired regarding the care of her infant, ways of caring for the
infant, hygiene and sanitary habits, and the pattern of referral to
health professionals. The last topic relates to emotions mothers might
experience towards their infant.
Results: Mothers from both cultural groups present some similar
caring behaviors, which may express a universal aspect of mothers'
behavior towards their infants. However, immigrant mothers differ
significantly from native born by relying less on their mothers' and
grandmothers' experience, they wean their infants from diapers
earlier, they are stricter about hygiene and sanitary habits and they
tend to consult a physician when their infant has low fever. Native
born and immigrant mothers differ in their expressions of pride and
wonder. Immigrant mothers report of a lesser degree of these
emotions towards their infants than native born mothers.
Conclusion: The theoretical model of socialization and
acculturation of immigrant mothers is employed as an explanatory
model for the current findings Young immigrant mothers undergo a
complex acculturation process and adapt behavioral patterns in
various areas to comply with Israeli norms and values, demonstrating
assimilation. In other areas they adhere to the norms of their original
culture.
Abstract: A reconfigurable manufacturing system (RMS) is an
advanced system designed at the outset for rapid changes in its hardware
and software components in order to quickly adjust its production
capacity and functionally. Among various operational decisions, this
study considers the scheduling problem that determines the input
sequence and schedule at the same time for a given set of parts. In
particular, we consider the practical constraints that the numbers of
pallets/fixtures are limited and hence a part can be released into the
system only when the fixture required for the part is available. To
solve the integrated input sequencing and scheduling problems, we
suggest a priority rule based approach in which the two sub-problems
are solved using a combination of priority rules. To show the effectiveness
of various rule combinations, a simulation experiment was
done on the data for a real RMS, and the test results are reported.
Abstract: MOSCAPs of various combinations of Hafnium
oxide and Titanium oxide of varying thickness with Aluminum as gate electrode have been fabricated and electrically characterized.
The effects of voltage stress on the I-V characteristics for prolonged time durations have been studied and compared. Results showed
hard breakdown and negligible degradation of reliability under stress.
Abstract: In order to integrate knowledge in heterogeneous
case-based reasoning (CBR) systems, ontology-based CBR system
has become a hot topic. To solve the facing problems of
ontology-based CBR system, for example, its architecture is
nonstandard, reusing knowledge in legacy CBR is deficient, ontology
construction is difficult, etc, we propose a novel approach for
semi-automatically construct ontology-based CBR system whose
architecture is based on two-layer ontology. Domain knowledge
implied in legacy case bases can be mapped from relational database
schema and knowledge items to relevant OWL local ontology
automatically by a mapping algorithm with low time-complexity. By
concept clustering based on formal concept analysis, computing
concept equation measure and concept inclusion measure, some
suggestions about enriching or amending concept hierarchy of OWL
local ontologies are made automatically that can aid designers to
achieve semi-automatic construction of OWL domain ontology.
Validation of the approach is done by an application example.