Abstract: A shaft-type activated sludge reactor has been
developed in order to study the feasibility of high-rate wastewater
treatment. The reactor having volume of about 14.5 L was operated
with the acclimated mixed activated sludge under batch and
continuous mode using a synthetic wastewater as feed. The batch
study was performed with varying chemical oxygen demand (COD)
concentrations of 1000–3500 mg·L-1 for a batch period up to 9 h. The
kinetic coefficients: Ks, k, Y and kd were obtained as 2040.2 mg·L-1
and 0.105 h-1, 0.878 and 0.0025 h-1 respectively from Monod-s
approach. The continuous study showed a stable and steady state
operation for a hydraulic retention time (HRT) of 8 h and influent
COD of about 1000 mg·L-1. A maximum COD removal efficiency of
about 80% was attained at a COD loading rate and food-tomicroorganism
(F/M) ratio (COD basis) of 3.42 kg·m-3d-1 and 1.0
kg·kg-1d-1 respectively under a HRT of 8 h. The reactor was also
found to handle COD loading rate and F/M ratio of 10.8 kg·m-3d-1
and 2.20 kg·kg-1d-1 respectively showing a COD removal efficiency
of about 46%.
Abstract: The gas safety management system using an
intelligent gas meter we proposed is to monitor flow and
pressure of gas, earthquake, temperature, smoke and leak of
methane. Then our system takes safety measures to protect a
serious risk by the result of an event, to communicate with a
wall-pad including a gateway by zigbee network in buildings
and to report the event to user by the safety management
program in a server. Also, the inner cutoff valve of an
intelligent gas meter is operated if any event occurred or
abnormal at each sensor.
Abstract: Surgical site infections (SSIs) are the most common
nosocomial infection in surgical patients resulting in significant
increases in postoperative morbidity and mortality. The commonly
causative bacteria developed resistance to virtually all antibiotics
available. The aim of this study was to isolation and identification the
most common bacteria that cause SSIs in Medical Research Institute,
and to compare their sensitivity to selected group of antibiotics and
natural products (garlic, oregano, olive, and Nigella sativa oils). The
isolated pathogens collected from infected surgical wounds were
identified, and their sensitivities to the antibiotics commonly
available for clinical use, and also to the different concentrations of
the used natural products were investigated. The results indicate to
the potential therapeutic effect of the tested natural products in
treatment of surgical wound infections.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Most of the drugs used for pharmaceutical purposes
are poorly water-soluble drugs. About 40% of all newly discovered
drugs are lipophilic and the numbers of lipophilic drugs seem to
increase more and more. Drug delivery systems such as
nanoparticles, micelles or liposomes are applied to improve their
solubility and thus their bioavailability. Besides various techniques of
solubilization, oil-in-water emulsions are often used to incorporate
lipophilic drugs into the oil phase. To stabilize emulsions surface
active substances (surfactants) are generally used. An alternative
method to avoid the application of surfactants was of great interest.
One possibility is to develop O/W-emulsion without any addition of
surface active agents or the so called “surfactant-free emulsion or
SFE”. The aim of this study was to develop and characterize SFE as a
drug carrier by varying the production conditions. Lidocaine base
was used as a model drug. The injection method was developed.
Effects of ultrasound as well as of temperature on the properties of
the emulsion were studied. Particle sizes and release were
determined. The long-term stability up to 30 days was performed.
The results showed that the surfactant-free O/W emulsions with
pharmaceutical oil as drug carrier can be produced.
Abstract: Commercially available lipases (Candida antarctica lipase B, Novozyme 435, Thermomyces lanuginosus lipase, and Lipozyme TL IM), as well as sol-gel immobilized lipases, have been screened for their ability to acylate regioselectively xylitol, sorbitol, and mannitol with a phenolic ester in a binary mixture of t-butanol and dimethylsulfoxide. HPLC and MALDI-TOF MS analysis revealed the exclusive formation of monoesters for all studied sugar alcohols. The lipases immobilized by the sol-gel entrapment method proved to be efficient catalysts, leading to high conversions (up to 60%) in the investigated acylation reactions. From a sequence of silane precursors with different nonhydrolyzable groups in their structure, the presence of octyl and i-butyl group was most beneficial for the catalytic activity of sol-gel entrapped lipases in the studied process.
Abstract: Compression algorithms reduce the redundancy in
data representation to decrease the storage required for that data.
Lossless compression researchers have developed highly
sophisticated approaches, such as Huffman encoding, arithmetic
encoding, the Lempel-Ziv (LZ) family, Dynamic Markov
Compression (DMC), Prediction by Partial Matching (PPM), and
Burrows-Wheeler Transform (BWT) based algorithms.
Decompression is also required to retrieve the original data by
lossless means. A compression scheme for text files coupled with
the principle of dynamic decompression, which decompresses only
the section of the compressed text file required by the user instead of
decompressing the entire text file. Dynamic decompressed files offer
better disk space utilization due to higher compression ratios
compared to most of the currently available text file formats.
Abstract: Wireless LAN technologies have picked up
momentum in the recent years due to their ease of deployment, cost
and availability. The era of wireless LAN has also given rise to
unique applications like VOIP, IPTV and unified messaging.
However, these real-time applications are very sensitive to network
and handoff latencies. To successfully support these applications,
seamless roaming during the movement of mobile station has become
crucial. Nowadays, centralized architecture models support roaming
in WLANs. They have the ability to manage, control and
troubleshoot large scale WLAN deployments. This model is managed
by Control and Provision of Wireless Access Point protocol
(CAPWAP). This paper covers the CAPWAP architectural solution
along with its proposals that have emerged. Based on the literature
survey conducted in this paper, we found that the proposed
algorithms to reduce roaming latency in CAPWAP architecture do
not support seamless roaming. Additionally, they are not sufficient
during the initial period of the network. This paper also suggests
important design consideration for mobility support in future
centralized IEEE 802.11 networks.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Aluminum salt that is generally presents as a solid
phase in the water purification sludge (WPS) can be dissolved,
recovering a liquid phase, by adding strong acid to the sludge solution.
According to the reaction kinetics, when reactant is in the form of
small particles with a large specific surface area, or when the reaction
temperature is high, the quantity of dissolved aluminum salt or
reaction rate, respectively are high. Therefore, in this investigation,
water purification sludge (WPS) solution was treated with ultrasonic
waves to break down the sludge, and different acids (1 N HCl and 1 N
H2SO4) were used to acidify it. Acid dosages that yielded the solution
pH of less than two were used. The results thus obtained indicate that
the quantity of dissolved aluminum in H2SO4-acidified solution
exceeded that in HCl-acidified solution. Additionally, ultrasonic
treatment increased the rate of dissolution of aluminum and the
amount dissolved. The quantity of aluminum dissolved at 60℃ was 1.5
to 2.0 times higher than that at 25℃.
Abstract: In the study the influence of the physical-chemical properties of a liquid, the width of a channel gap and the superficial liquid and gas velocities on the patterns formed during two phase flows in vertical, narrow mini-channels was investigated. The research was performed in the channels of rectangular cross-section and of dimensions: 15 x 0.65 mm and 7.5 x 0.73 mm. The experimental data were compared with the published criteria of the transitions between the patterns of two-phase flows.
Abstract: Packet switched data network like Internet, which has
traditionally supported throughput sensitive applications such as email
and file transfer, is increasingly supporting delay-sensitive
multimedia applications such as interactive video. These delaysensitive
applications would often rather sacrifice some throughput
for better delay. Unfortunately, the current packet switched network
does not offer choices, but instead provides monolithic best-effort
service to all applications. This paper evaluates Class Based Queuing
(CBQ), Coordinated Earliest Deadline First (CEDF), Weighted
Switch Deficit Round Robin (WSDRR) and RED-Boston scheduling
schemes that is sensitive to delay bound expectations for variety of
real time applications and an enhancement of WSDRR is proposed.
Abstract: An experiment was conducted to examine the effect of the level of performance stabilization on the human adaptability to perceptual-motor perturbation in a complex coincident timing task. Three levels of performance stabilization were established operationally: pre-stabilization, stabilization, and super-stabilization groups. Each group practiced the task until reached its level of stabilization in a constant sequence of movements and under a constant time constraint before exposure to perturbation. The results clearly showed that performance stabilization is a pre-condition for adaptation. Moreover, variability before reaching stabilization is harmful to adaptation and persistent variability after stabilization is beneficial. Moreover, the behavior of variability is specific to each measure.
Abstract: In online context, the design and implementation of
effective remote laboratories environment is highly challenging on
account of hardware and software needs. This paper presents the
remote laboratory software framework modified from ilab shared
architecture (ISA). The ISA is a framework which enables students to
remotely acccess and control experimental hardware using internet
infrastructure. The need for remote laboratories came after
experiencing problems imposed by traditional laboratories. Among
them are: the high cost of laboratory equipment, scarcity of space,
scarcity of technical personnel along with the restricted university
budget creates a significant bottleneck on building required
laboratory experiments. The solution to these problems is to build
web-accessible laboratories. Remote laboratories allow students and
educators to interact with real laboratory equipment located
anywhere in the world at anytime. Recently, many universities and
other educational institutions especially in third world countries rely
on simulations because they do not afford the experimental
equipment they require to their students. Remote laboratories enable
users to get real data from real-time hand-on experiments. To
implement many remote laboratories, the system architecture should
be flexible, understandable and easy to implement, so that different
laboratories with different hardware can be deployed easily. The
modifications were made to enable developers to add more
equipment in ISA framework and to attract the new developers to
develop many online laboratories.
Abstract: In this paper static and dynamic response of a
varactor of a micro-phase shifter to DC, step DC and AC
voltages have been studied. By presenting a mathematical
modeling Galerkin-based step by step linearization method
(SSLM) and Galerkin-based reduced order model have been
used to solve the governing static and dynamic equations,
respectively. The calculated static and dynamic pull-in
voltages have been validated by previous experimental and
theoretical results and a good agreement has been achieved.
Then the frequency response and phase diagram of the system
has been studied. It has been shown that applying the DC
voltage shifts down the phase diagram and frequency
response. Also increasing the damping ratio shifts up the
phase diagram.
Abstract: The objective of this work is to explicit knowledge on the interactions between the chlorophyll-a and nine meroplankton larvae of epibenthonic fauna. The studied case is the Arraial do Cabo upwelling system, Southeastern of Brazil, which provides different environmental conditions. To assess this information a network approach based in probability estimative was used. Comparisons among the generated graphs are made in the light of different water masses, application of Shannon biodiversity index, and the closeness and betweenness centralities measurements. Our results show the main pattern among different water masses and how the core organisms belonging to the network skeleton are correlated to the main environmental variable. We conclude that the approach of complex networks is a promising tool for environmental diagnostic.
Abstract: This Paper presents an on-going research in the area of Model-Driven Engineering (MDE). The premise is that UML is too unwieldy to serve as the basis for model-driven engineering. We need a smaller, simpler notation with a cleaner semantics. We propose some ideas for a simpler notation with a clean semantics. The result is known as μML, or the Micro-Modelling Language.
Abstract: The carbon based coils with the nanometer scale have
the 3 dimension helix geometry. We synthesized the carbon nano-coils
by the use of chemical vapor deposition technique with iron and tin as
the catalysts. The fabricated coils have the external diameter of
ranging few hundred nm to few thousand nm. The Scanning
Electro-Microscope (SEM) and Tunneling Electro-Microscope has
shown detail images of the coil-s structure. The fabrication of the
carbon nano-coils can be grown on the metal and non-metal substrates,
such as the stainless steel and silicon substrates. Besides growth on the
flat substrate; they also can be grown on the stainless steel wires. After
the synthesis of the coils, the mechanical and electro-mechanical
property is measured. The experimental results were reported.
Abstract: The usual correctness condition for a schedule of
concurrent database transactions is some form of serializability of
the transactions. For general forms, the problem of deciding whether
a schedule is serializable is NP-complete. In those cases other approaches
to proving correctness, using proof rules that allow the steps
of the proof of serializability to be guided manually, are desirable.
Such an approach is possible in the case of conflict serializability
which is proved algebraically by deriving serial schedules using
commutativity of non-conflicting operations. However, conflict serializability
can be an unnecessarily strong form of serializability restricting
concurrency and thereby reducing performance. In practice,
weaker, more general, forms of serializability for extended models of
transactions are used. Currently, there are no known methods using
proof rules for proving those general forms of serializability. In this
paper, we define serializability for an extended model of partitioned
transactions, which we show to be as expressive as serializability
for general partitioned transactions. An algebraic method for proving
general serializability is obtained by giving an initial-algebra specification
of serializable schedules of concurrent transactions in the
model. This demonstrates that it is possible to conduct algebraic
proofs of correctness of concurrent transactions in general cases.