Abstract: In this study, a double-sided linear switched reluctance
motor (LSRM) drive was investigated as an alternative actuator for
vertical linear transportation applications such as a linear elevator
door, hospital and subway doors which move linearly and where
accurate position control and rapid response is requested. A prototype
sliding elevator door that is focused on a home elevator with LSRMs
is designed. The motor has 6/4 poles, 3 phases, 8A, 24V, 250 W and
250 N pull forces. Air gap between rotor and translator poles of the
designed motor and phase coil-s ideal inductance profile are obtained
in compliance with the geometric dimensions. Operation and
switching sections as motor and generator has been determined from
the inductance profile.
Abstract: Real world Speaker Identification (SI) application
differs from ideal or laboratory conditions causing perturbations that
leads to a mismatch between the training and testing environment
and degrade the performance drastically. Many strategies have been
adopted to cope with acoustical degradation; wavelet based Bayesian
marginal model is one of them. But Bayesian marginal models
cannot model the inter-scale statistical dependencies of different
wavelet scales. Simple nonlinear estimators for wavelet based
denoising assume that the wavelet coefficients in different scales are
independent in nature. However wavelet coefficients have significant
inter-scale dependency. This paper enhances this inter-scale
dependency property by a Circularly Symmetric Probability Density
Function (CS-PDF) related to the family of Spherically Invariant
Random Processes (SIRPs) in Log Gabor Wavelet (LGW) domain
and corresponding joint shrinkage estimator is derived by Maximum
a Posteriori (MAP) estimator. A framework is proposed based on
these to denoise speech signal for automatic speaker identification
problems. The robustness of the proposed framework is tested for
Text Independent Speaker Identification application on 100 speakers
of POLYCOST and 100 speakers of YOHO speech database in three
different noise environments. Experimental results show that the
proposed estimator yields a higher improvement in identification
accuracy compared to other estimators on popular Gaussian Mixture
Model (GMM) based speaker model and Mel-Frequency Cepstral
Coefficient (MFCC) features.
Abstract: In this paper, fabrication and study of electronic properties of Au/methyl-red/Ag surface type Schottky diode by current-voltage (I-V) method has been reported. The I-V characteristics of the Schottky diode showed the good rectifying behavior. The values of ideality factor n and barrier height b of Au/methyl-red/Ag Schottky diode were calculated from the semi-log I-V characteristics and by using the Cheung functions. From semi-log current-voltage characteristics the values of n and b were found 1.93 and 0.254 eV, respectively, while by using Cheung functions their values were calculated 1.89 and 0.26 eV, respectively. The effect of series resistance was also analyzed by Cheung functions. The series resistance RS values were determined from dV/d(lnI)–I and H(I)–I graphs and were found to be 1.1 k and 1.3 k, respectively.
Abstract: COSMED K4b2 is a portable electrical device designed to test pulmonary functions. It is ideal for many applications that need the measurement of the cardio-respiratory response either in the field or in the lab is capable with the capability to delivery real time data to a sink node or a PC base station with storing data in the memory at the same time. But the actual sensor outputs and data received may contain some errors, such as impulsive noise which can be related to sensors, low batteries, environment or disturbance in data acquisition process. These abnormal outputs might cause misinterpretations of exercise or living activities to persons being monitored. In our paper we propose an effective and feasible method to detect and identify errors in applications by principal component analysis (PCA) and a back propagation (BP) neural network.
Abstract: In this paper, we introduce the notion θ-Euclidean k-fuzzy ideal in semirings and to study the properties of the image and pre image of a θ -Euclidean k-fuzzy ideal in a semirings under epimorphism.
Abstract: Studying literature theme in the fields of tourism and
sustainable development and its importance in today world and their
criteria in architecture, here in this article we will also study the area
where the selected site is located; beside the Aab-Ask Village located
in Larijan region in Mazandaran province on the way to Haraz – one
of the tourism routes of Iran. After these studies by analyzing the
site, its strong potentials – such as mineral water springs (hot
springs), geothermal, landscapes and ideal climate - as a tourist
attraction spot in the region, and considering sustainable
development criteria – with regard to limits and available facilities –
a plan was offered that could change the region to provide the needs
of local people and in addition change it to a place where tourism
services is offered to the visitors and make it an acceptable sample of
stable building in Iran. Finally the reason to make design for this
complex is recovery of natural and historical values of Aab-Ask area
regarding development and sustainable architecture criteria in the
form of a functional sample which can be a suitable place to fulfill
this goal for having lots of strong points in attracting cultural and
sustainable tourist.
Abstract: Due to dynamic evolution, the ability of a
manufacturing technology to produce a special product is changing.
Therefore, it is essential to monitor the established techniques and
processes to detect whether a company-s production will fit future
circumstances. Concerning the manufacturing technology planning
process, companies must decide when to change to a new technology
for maintaining and increasing competitive advantages. In this
context, the maturity assessment of the focused technologies is
crucial. This article presents an approach for defining the maturity of
a manufacturing technology from a strategic point of view. The
concept is based on the approach of technology readiness level
(TRL) according to NASA (National Aeronautics and Space
Administration), but also includes dynamic changes. Therefore, the
model takes into account the concept of the technology life cycle.
Furthermore, it enables a company to estimate the ideal date for
implementation of a new manufacturing technology.
Abstract: Anodizing is an electrochemical process that converts the metal surface into a decorative, durable, corrosion-resistant, anodic oxide finish. Aluminum is ideally suited to anodizing, although other nonferrous metals, such as magnesium and titanium, also can be anodized. The anodic oxide structure originates from the aluminum substrate and is composed entirely of aluminum oxide. This aluminum oxide is not applied to the surface like paint or plating, but is fully integrated with the underlying aluminum substrate, so cannot chip or peel. It has a highly ordered, porous structure that allows for secondary processes such as coloring and sealing. In this experimental paper, we focus on a reliable method for fabricating nanoporous alumina with high regularity. Starting from study of nanostructure materials synthesize methods. After that, porous alumina fabricate in the laboratory by anodization of aluminum oxide. Hard anodization processes are employed to fabricate the nanoporous alumina using 0.3M oxalic acid and 90, 120 and 140 anodized voltages. The nanoporous templates were characterized by SEM and FFT. The nanoporous templates using 140 voltages have high ordered. The pore formation, influence of the experimental conditions on the pore formation, the structural characteristics of the pore and the oxide chemical reactions involved in the pore growth are discuss.
Abstract: Crude oil blending is an important unit operation in
petroleum refining industry. A good model for the blending system is
beneficial for supervision operation, prediction of the export
petroleum quality and realizing model-based optimal control. Since
the blending cannot follow the ideal mixing rule in practice, we
propose a static neural network to approximate the blending
properties. By the dead-zone approach, we propose a new robust
learning algorithm and give theoretical analysis. Real data of crude
oil blending is applied to illustrate the neuro modeling approach.
Abstract: This paper presents a method of reducing the feedback
delay time of DWA(Data Weighted Averaging) used in sigma-delta
modulators. The delay time reduction results from the elimination of
the latch at the quantizer output and also from the falling edge
operation. The designed sigma-delta modulator improves the timing
margin about 16%. The sub-circuits of sigma-delta modulator such as
SC(Switched Capacitor) integrator, 9-level quantizer, comparator, and
DWA are designed with the non-ideal characteristics taken into
account. The sigma-delta modulator has a maximum SNR (Signal to
Noise Ratio) of 84 dB or 13 bit resolution.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: Supplier selection, in real situation, is affected by
several qualitative and quantitative factors and is one of the most
important activities of purchasing department. Since at the time of
evaluating suppliers against the criteria or factors, decision makers
(DMS) do not have precise, exact and complete information, supplier
selection becomes more difficult. In this case, Grey theory helps us
to deal with this problem of uncertainty. Here, we apply Technique
for Order Preference by Similarity to Ideal Solution (TOPSIS)
method to evaluate and select the best supplier by using interval
fuzzy numbers. Through this article, we compare TOPSIS with some
other approaches and afterward demonstrate that the concept of
TOPSIS is very important for ranking and selecting right supplier.
Abstract: Group contribution based models are widely used in
industrial applications for its convenience and flexibility. Although a
number of group contribution models have been proposed, there were
certain limitations inherent to those models. Models based on group
contribution excess Gibbs free energy are limited to low pressures and
models based on equation of state (EOS) cannot properly describe
highly nonideal mixtures including acids without introducing
additional modification such as chemical theory. In the present study
new a new approach derived from quantum chemistry have been used
to calculate necessary EOS group interaction parameters. The
COSMO-RS method, based on quantum mechanics, provides a
reliable tool for fluid phase thermodynamics. Benefits of the group
contribution EOS are the consistent extension to hydrogen-bonded
mixtures and the capability to predict polymer-solvent equilibria up to
high pressures. The authors are confident that with a sufficient
parameter matrix the performance of the lattice EOS can be improved
significantly.
Abstract: In this paper present a sensorless maximum wind power extraction for variable speed constant frequency (VSCF) wind power generation systems with a doubly-fed induction generators (DFIG), to ensure stability and to impose the ideal feedback control solution despite of model uncertainties , using the principles of an active and reactive power controller (DPC) a robust sliding mode power control has been proposed to guarantees fast response times and precise control actions for control the active and reactive power independently. The simulation results in MATLAB/Simulink platform confirmed the good dynamic performance of power control approach for DFIGbased variable speed wind turbines.
Abstract: Vertical Double Gate (DG) Metal Oxide Semiconductor Field Effect Transistor (MOSFET) is believed to suppress various short channel effect problems. The gate to channel coupling in vertical DG-MOSFET are doubled, thus resulting in higher current density. By having two gates, both gates are able to control the channel from both sides and possess better electrostatic control over the channel. In order to ensure that the transistor possess a superb turn-off characteristic, the subs-threshold swing (SS) must be kept at minimum value (60-90mV/dec). By utilizing SILVACO TCAD software, an n-channel vertical DG-MOSFET was successfully designed while keeping the sub-threshold swing (SS) value as minimum as possible. From the observation made, the value of sub-threshold swing (SS) was able to be varied by adjusting the height of the silicon pillar. The minimum value of sub-threshold swing (SS) was found to be 64.7mV/dec with threshold voltage (VTH) of 0.895V. The ideal height of the vertical DG-MOSFET pillar was found to be at 0.265 µm.
Abstract: Healthcare providers sometimes use the power of
humor as a treatment and therapy for buffering mental health or easing
mental disorders because humor can provide relief from distress and
conflict. Humor is also very suitable for advertising because of similar
benefits. This study carefully examines humor's widespread use in
advertising and identifies relationships among humor mechanisms,
female depictions, and product types. The purpose is to conceptualize
how humor theories can be used not only to successfully define a
product as fitting within one of four color categories of the product
color matrix, but also to identify compelling contemporary female
depictions through humor in ads. The results can offer an idealization
for marketing managers and consumers to help them understand how
female role depictions can be effectively used with humor in ads. The
four propositions developed herein are derived from related literature,
through the identification of marketing strategy formulations that
achieve product memory enhancement by adopting humor
mechanisms properly matched with female role depictions.
Abstract: Super resolution (SR) technologies are now being
applied to video to improve resolution. Some TV sets are now
equipped with SR functions. However, it is not known if super
resolution image reconstruction (SRR) for TV really works or not.
Super resolution with non-linear signal processing (SRNL) has
recently been proposed. SRR and SRNL are the only methods for
processing video signals in real time. The results from subjective
assessments of SSR and SRNL are described in this paper. SRR video
was produced in simulations with quarter precision motion vectors and
100 iterations. These are ideal conditions for SRR. We found that the
image quality of SRNL is better than that of SRR even though SRR
was processed under ideal conditions.
Abstract: In this study, the Scots pine (Pinus sylvestris L.) C
needles (i.e. the current-year-needles) were used as bioindicators in
determining the aerial distribution pattern of sulphur emissions
around industrial point sources at Kemi, Northern Finland. The
average sulphur concentration in the C needles was 897 mg/kg
(d.w.), with a standard deviation of 118 mg/kg (d.w.) and range 740 –
1350 mg/kg (d.w.). According to results in this study, Scots pine
needles (Pinus sylvestris L.) appear to be an ideal bioindicators for
identifying atmospheric sulphur pollution derived from industrial
plants and can complement the information provided by plant
mapping studies around industrial plants.
Abstract: A measurement system for pH array sensors is
introduced to increase accuracy, and decrease non-ideal effects
successfully. An array readout circuit reads eight potentiometric
signals at the same time, and obtains an average value. The deviation
value or the extreme value is counteracted and the output voltage is a
relatively stable value. The errors of measuring pH buffer solutions are
decreased obviously with this measurement system, and the non-ideal
effects, drift and hysteresis, are lowered to 1.638mV/hr and 1.118mV,
respectively. The efficiency and stability are better than single sensor.
The whole sensing characteristics are improved.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.