Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and Choram
are the most important and populated cities in this area. The study
was undertaken to assess the status of water quality in the urban areas
of the Kowsar dam. A total of 28 water samples were collected from
6 stations on surface water and 1 station from groundwater on the
watershed of the Kowsar dam. All the samples were analyzed for Ni
concentration using standard procedures. The results were compared
with other national and international standards. Among the analyzed
samples, as the maximum value of Nickel (0.01 mg/L) was observed
on the station 2 at the autumn 2010, all the samples analyzed were
within the maximum admissible limits by the United States
Environmental Protection Agency, EU, WHO and the Iranian. In
general results of the present study have shown that a Ni mean value
of station No. 2 with 0.006 mg/L is higher than the other stations. Ni
level of all samples and stations have had normal values and this is an
indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watersheds.
Abstract: In a state-of-the-art industrial production line of
photovoltaic products the handling and automation processes are of
particular importance and implication. While processing a fully
functional crystalline solar cell an as-cut photovoltaic wafer is subject
to numerous repeated handling steps. With respect to stronger
requirements in productivity and decreasing rejections due to defects
the mechanical stress on the thin wafers has to be reduced to a
minimum as the fragility increases by decreasing wafer thicknesses.
In relation to the increasing wafer fragility, researches at the
Fraunhofer Institutes IPA and CSP showed a negative correlation
between multiple handling processes and the wafer integrity. Recent
work therefore focused on the analysis and optimization of the dry
wafer stack separation process with compressed air. The achievement
of a wafer sensitive process capability and a high production
throughput rate is the basic motivation in this research.
Abstract: Defining strategic position of the organizations within
the industry environment is one of the basic and most important
phases of strategic planning to which extent that one of the
fundamental schools of strategic planning is the strategic positioning
school. In today-s knowledge-based economy and dynamic
environment, it is essential for universities as the centers of
education, knowledge creation and knowledge worker evolvement.
Till now, variant models with different approaches to strategic
positioning are deployed in defining the strategic position within the
various industries. Balanced Scorecard as one of the powerful models
for strategic positioning, analyzes all aspects of the organization
evenly. In this paper with the consideration of BSC strength in
strategic evaluation, it is used for analyzing the environmental
position of the best-s Iranian Business Schools. The results could be
used in developing strategic plans for these schools as well as other
Iranian Management and Business Schools.
Abstract: In China, with the rapid urbanization and
industrialization, and highly accelerated economic development have
resulted in degradation of water resource. The water quality
deterioration usual result from eutrophication in most cases, so how to
dispose this type pollution water higher efficiently is an urgent task.
Hower, different with traditional technology, constructed wetlands are
effective treatment systems that can be very useful because they are
simple technology and low operational cost. A pilot-scale treatment
including constructed wetlands was constructed at XingYun Lake,
Yuxi, China, and operated as primary treatment measure before
eutrophic-lake water draining to riverine landscape. Water quality
indices were determined during the experiment, the results indicated
that treatment removal efficiencies were high for Nitrate nitrogen,
Chlorophyll–a and Algae, the final removal efficiency reached to
95.20%, 93.33% and 99.87% respectively, but the removal efficiency
of Total phosphorous and Total nitrogen only reach to 68.83% and
50.00% respectively.
Abstract: Modern civilization has come in recent decades into a new phase in its development, called the information society. The concept of "information society" has become one of the most common. Therefore, the attempt to understand what exactly the society we live in, what are its essential features, and possible future scenarios, is important to the social and philosophical analysis. At the heart of all these deep transformations is more increasing, almost defining role knowledge and information as play substrata of «information society». The mankind opened for itself and actively exploits a new resource – information. Information society puts forward on the arena new type of the power, at the heart of which activity – mastering by a new resource: information and knowledge. The password of the new power – intelligence as synthesis of knowledge, information and communications, the strength of mind, fundamental sociocultural values. In a postindustrial society, the power of knowledge and information is crucial in the management of the company, pushing into the background the influence of money and state coercion.
Abstract: Distillation column is one of the most common
operations in process industries and is while the most expensive unit
of the amount of energy consumption. Many ideas have been
presented in the related literature for optimizing energy consumption
in distillation columns. This paper studies the different heat
integration methods in a distillation column which separate Benzene,
Toluene, Xylene, and C9+. Three schemes of heat integration
including, indirect sequence (IQ), indirect sequence with forward
energy integration (IQF), and indirect sequence with backward
energy integration (IQB) has been studied in this paper. Using
shortcut method these heat integration schemes were simulated with
Aspen HYSYS software and compared with each other with
regarding economic considerations. The result shows that the energy
consumption has been reduced 33% in IQF and 28% in IQB in
comparison with IQ scheme. Also the economic result shows that the
total annual cost has been reduced 12% in IQF and 8% in IQB
regarding with IQ scheme. Therefore, the IQF scheme is most
economic than IQB and IQ scheme.
Abstract: R&D risk management has been suggested as one of
the management approaches for accomplishing the goals of public
R&D investment. The investment in basic science and core technology
development is the essential roles of government for securing the
social base needed for continuous economic growth. And, it is also an
important role of the science and technology policy sectors to generate
a positive environment in which the outcomes of public R&D can be
diffused in a stable fashion by controlling the uncertainties and risk
factors in advance that may arise during the application of such
achievements to society and industry. Various policies have already
been implemented to manage uncertainties and variables that may
have negative impact on accomplishing public R& investment goals.
But we may derive new policy measures for complementing the
existing policies and for exploring progress direction by analyzing
them in a policy package from the viewpoint of R&D risk
management.
Abstract: Very few studies have examined performance
implications of strategic alliance announcements in the information
technologies industry from a resource-based view. Furthermore, none
of these studies have investigated resource congruence and alliance
motive as potential sources of abnormal firm performance. This paper
extends upon current resource-based literature to discover and explore
linkages between these concepts and the practical performance of
strategic alliances. This study finds that strategic alliance
announcements have provided overall abnormal positive returns, and
that marketing alliances with marketing resource incongruence have
also contributed to significant firm performance.
Abstract: The objective of this research is to investigate the
advantages of using large-diameter 0.7 inch prestressing strands in
pretention applications. The advantages of large-diameter strands are
mainly beneficial in the heavy construction applications. Bridges and
tunnels are subjected to a higher daily traffic with an exponential
increase in trucks ultimate weight, which raise the demand for higher
structural capacity of bridges and tunnels. In this research, precast
prestressed I-girders were considered as a case study. Flexure
capacities of girders fabricated using 0.7 inch strands and different
concrete strengths were calculated and compared to capacities of 0.6
inch strands girders fabricated using equivalent concrete strength.
The effect of bridge deck concrete strength on composite deck-girder
section capacity was investigated due to its possible effect on final
section capacity. Finally, a comparison was made to compare the
bridge cross-section of girders designed using regular 0.6 inch strands
and the large-diameter 0.7 inch. The research findings showed that
structural advantages of 0.7 inch strands allow for using fewer bridge
girders, reduced material quantity, and light-weight members. The
structural advantages of 0.7 inch strands are maximized when high
strength concrete (HSC) are used in girder fabrication, and concrete
of minimum 5ksi compressive strength is used in pouring bridge
decks. The use of 0.7 inch strands in bridge industry can partially
contribute to the improvement of bridge conditions, minimize
construction cost, and reduce the construction duration of the project.
Abstract: Nanotechnology is the science of creating, using and
manipulating objects which have at least one dimension in range of
0.1 to 100 nanometers. In other words, nanotechnology is
reconstructing a substance using its individual atoms and arranging
them in a way that is desirable for our purpose.
The main reason that nanotechnology has been attracting
attentions is the unique properties that objects show when they are
formed at nano-scale. These differing characteristics that nano-scale
materials show compared to their nature-existing form is both useful
in creating high quality products and dangerous when being in
contact with body or spread in environment.
In order to control and lower the risk of such nano-scale particles,
the main following three topics should be considered:
1) First of all, these materials would cause long term diseases that
may show their effects on body years after being penetrated in human
organs and since this science has become recently developed in
industrial scale not enough information is available about their
hazards on body.
2) The second is that these particles can easily spread out in
environment and remain in air, soil or water for very long time,
besides their high ability to penetrate body skin and causing new
kinds of diseases.
3) The third one is that to protect body and environment against
the danger of these particles, the protective barriers must be finer than
these small objects and such defenses are hard to accomplish.
This paper will review, discuss and assess the risks that human and
environment face as this new science develops at a high rate.
Abstract: This paper studies the duration or survival time of commercial banks active in the Moscovian three month Rouble deposits market, during the 1994-1997 period. The privatization process of the Russian commercial banking industry, after the 1988 banking reform, caused a massive entry of new banks followed by a period of high rates of exit. As a consequence, many firms went bankrupt without refunding their deposits. Therefore, both for the banks and for the banks- depositors, it is of interest to analyze which are the significant characteristics that motivate the exit or the closing of the bank. We propose a different methodology based on penalized weighted least squares which represents a very general, flexible and innovative approach for this type of analysis. The more relevant results are that smaller banks exit sooner, banks that enter the market in the last part of the study have shorter durations. As expected, the more experienced banks have a longer duration in the market. In addition, the mean survival time is lower for banks which offer extreme interest rates.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: With the increasing number of on-chip components and the critical requirement for processing power, Chip Multiprocessor (CMP) has gained wide acceptance in both academia and industry during the last decade. However, the conventional bus-based onchip communication schemes suffer from very high communication delay and low scalability in large scale systems. Network-on-Chip (NoC) has been proposed to solve the bottleneck of parallel onchip communications by applying different network topologies which separate the communication phase from the computation phase. Observing that the memory bandwidth of the communication between on-chip components and off-chip memory has become a critical problem even in NoC based systems, in this paper, we propose a novel 3D NoC with on-chip Dynamic Random Access Memory (DRAM) in which different layers are dedicated to different functionalities such as processors, cache or memory. Results show that, by using our proposed architecture, average link utilization has reduced by 10.25% for SPLASH-2 workloads. Our proposed design costs 1.12% less execution cycles than the traditional design on average.
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: The development of many measurement and inspection systems of products based on real-time image processing can not be carried out totally in a laboratory due to the size or the temperature of the manufactured products. Those systems must be developed in successive phases. Firstly, the system is installed in the production line with only an operational service to acquire images of the products and other complementary signals. Next, a recording service of the image and signals must be developed and integrated in the system. Only after a large set of images of products is available, the development of the real-time image processing algorithms for measurement or inspection of the products can be accomplished under realistic conditions. Finally, the recording service is turned off or eliminated and the system operates only with the real-time services for the acquisition and processing of the images. This article presents a systematic performance evaluation of the image compression algorithms currently available to implement a real-time recording service. The results allow establishing a trade off between the reduction or compression of the image size and the CPU time required to get that compression level.
Abstract: This article presents a simple way to perform programmed voice commands for the interface with commercial Digital and Analogue Input/Output PCI cards, used in Robotics and Automation applications. Robots and Automation equipment can "listen" to voice commands and perform several different tasks, approaching to the human behavior, and improving the human- machine interfaces for the Automation Industry. Since most PCI Digital and Analogue Input/Output cards are sold with several DLLs included (for use with different programming languages), it is possible to add speech recognition capability, using a standard speech recognition engine, compatible with the programming languages used. It was created in this work a Visual Basic 6 (the world's most popular language) application, that listens to several voice commands, and is capable to communicate directly with several standard 128 Digital I/O PCI Cards, used to control complete Automation Systems, with up to (number of boards used) x 128 Sensors and/or Actuators.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Currently, slider process of Hard Disk Drive Industry
become more complex, defective diagnosis for yield improvement
becomes more complicated and time-consumed. Manufacturing data
analysis with data mining approach is widely used for solving that
problem. The existing mining approach from combining of the KMean
clustering, the machine oriented Kruskal-Wallis test and the
multivariate chart were applied for defective diagnosis but it is still
be a semiautomatic diagnosis system. This article aims to modify an
algorithm to support an automatic decision for the existing approach.
Based on the research framework, the new approach can do an
automatic diagnosis and help engineer to find out the defective
factors faster than the existing approach about 50%.