Abstract: High-frequency (HF) communications have been used by military organizations for more than 90 years. The opportunity of very long range communications without the need for advanced equipment makes HF a convenient and inexpensive alternative of satellite communications. Besides the advantages, voice and data transmission over HF is a challenging task, because the HF channel generally suffers from Doppler shift and spread, multi-path, cochannel interference, and many other sources of noise. In constructing an HF data modem, all these effects must be taken into account. STANAG 4539 is a NATO standard for high-speed data transmission over HF. It allows data rates up to 12800 bps over an HF channel of 3 kHz. In this work, an efficient implementation of STANAG 4539 on a single Texas Instruments- TMS320C6747 DSP chip is described. The state-of-the-art algorithms used in the receiver and the efficiency of the implementation enables real-time high-speed data / digitized voice transmission over poor HF channels.
Abstract: In this study, synthesis of biomemitic patterned nano
hydroxyapatite-starch biocomposites using different concentration of
starch to evaluate effect of polymer alteration on biocomposites
structural properties has been reported. Formation of hydroxyapatite
nano particles was confirmed by X-ray diffraction (XRD) and Fourier
transform infrared spectroscopy (FT-IR). Size and morphology of the
samples were characterized using scanning and transmission electron
microscopy (SEM and TEM). It seems that by increasing starch
content, the more active site of polymer (oxygen atoms) can be
provided for interaction with Ca2+ followed by phosphate and
hydroxyl group.
Abstract: Triglycerides and their derivatives are considered as viable alternatives for diesel fuels. Rice bran oil is used as diesel fuel. Highly viscous rice bran oil can be reduced by blending it with diesel fuel. The present research is aimed to investigate experimentally the performance, exhaust emission and combustion characteristics of a direct injection (DI) diesel engine, typically used in agricultural sector, over the entire load range when fuelled with rice bran oil and diesel fuel blends, RB10 (10% rice bran oil + 90% diesel fuel) to RB50. The performance, emission and combustion parameters of RB20 were found to be very close to neat diesel fuel (ND). The injector opening pressure (IOP) undoubtedly is of prime importance in diesel engine operation. Performance, emission and combustion characteristics with RB30 at enhanced IOPs are better than ND. Improved premixed heat release rate were noticed with RB30 when the IOP is enhanced.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Bootstrapping has gained popularity in different tests of hypotheses as an alternative in using asymptotic distribution if one is not sure of the distribution of the test statistic under a null hypothesis. This method, in general, has two variants – the parametric and the nonparametric approaches. However, issues on reliability of this method always arise in many applications. This paper addresses the issue on reliability by establishing a reliability measure in terms of quantiles with respect to asymptotic distribution, when this is approximately correct. The test of hypotheses used is Ftest. The simulated results show that using nonparametric bootstrapping in F-test gives better reliability than parametric bootstrapping with relatively higher degrees of freedom.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: The fault current levels through the electric devices
have a significant impact on failure probability. New fault current
results in exceeding the rated capacity of circuit breaker and switching
equipments and changes operation characteristic of overcurrent relay.
In order to solve these problems, SFCL (Superconducting Fault
Current Limiter) has rising as one of new alternatives so as to improve
these problems. A fault current reduction differs depending on
installed location. Therefore, a location of SFCL is very important.
Also, SFCL decreases the fault current, and it prevents surrounding
protective devices to be exposed to fault current, it then will bring a
change of reliability. In this paper, we propose method which
determines the optimal location when SFCL is installed in power
system. In addition, the reliability about the power system which
SFCL was installed is evaluated. The efficiency and effectiveness of
this method are also shown by numerical examples and the reliability
indices are evaluated in this study at each load points. These results
show a reliability change of a system when SFCL was installed.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: Library management systems are commonly used in
all educational related institutes. Many commercial products are
available. However, many institutions may not be able to afford the
cost of using commercial products. Therefore, an alternative solution
in such situations would be open source software. This paper is
focusing on reviewing open source library management system
packages currently available. The review will focus on the abilities to
perform four basic components which are traditional services,
interlibrary load management, managing electronic materials and
basic common management system such as security, alert system and
statistical reports. In addition, environment, basic requirement and
supporting aspects of each open source package are also mentioned.
Abstract: In this paper, the authors present architecture of a multi agent consultation system for obesity related problems, which hybrid the technology of an expert system (ES) and an intelligent agent (IA). The strength of the ES which is capable of pulling the expert knowledge is consulted and presented to the end user via the autonomous and friendly pushing environment of the intelligent agent.
Abstract: The early diagnostic decision making in industrial processes is absolutely necessary to produce high quality final products. It helps to provide early warning for a special event in a process, and finding its assignable cause can be obtained. This work presents a hybrid diagnostic schmes for batch processes. Nonlinear representation of raw process data is combined with classification tree techniques. The nonlinear kernel-based dimension reduction is executed for nonlinear classification decision boundaries for fault classes. In order to enhance diagnosis performance for batch processes, filtering of the data is performed to get rid of the irrelevant information of the process data. For the diagnosis performance of several representation, filtering, and future observation estimation methods, four diagnostic schemes are evaluated. In this work, the performance of the presented diagnosis schemes is demonstrated using batch process data.
Abstract: Infrared focal plane arrays (IRFPA) sensors, due to
their high sensitivity, high frame frequency and simple structure, have
become the most prominently used detectors in military applications.
However, they suffer from a common problem called the fixed pattern
noise (FPN), which severely degrades image quality and limits the
infrared imaging applications. Therefore, it is necessary to perform
non-uniformity correction (NUC) on IR image. The algorithms of
non-uniformity correction are classified into two main categories, the
calibration-based and scene-based algorithms. There exist some
shortcomings in both algorithms, hence a novel non-uniformity
correction algorithm based on non-linear fit is proposed, which
combines the advantages of the two algorithms. Experimental results
show that the proposed algorithm acquires a good effect of NUC with
a lower non-uniformity ratio.
Abstract: An experiment was conducted under controlled
conditions to study the effect of water extract of leaves, shoots and
roots of either Sisymbrium irio L. =SISIR and/or Descurainia
sophia (L.) Schur =DESSO on the germination and primary growth
of wheat. A split-split plot experiment in CRD with three
replications was used. The main plots were the type of weed: i.e.
SISIR and DESSO and the sub-plots were type of organ: i.e. leaf,
stem and root and, the sub-sub plots were concentration of the
water extract of each organ of the weeds: i.e. 0, 2, 4 and 8 % w/v.
The plant materials were cut in 2-3 cm pieces and then were
ground in a blender. The crushed materials were weighed
according to experimental protocol and the final volume was
reached to 100 ml in distilled water in dark bottles. All bottles were
put on a shaker for 24 hours. The solutions were filtered by muslin
cloth. Whatman paper, 9 cm in diameter, were put in petri dishes
and twenty seeds of wheat were put on it and 5 ml distilled water
or water extract of weeds were added to each petri dish. All petri
dishes were put in constant temperature of 15 0C incubator.
The results showed that the SISIR water extract had a greater
inhibitory effects on germination and primary growth of wheat
than those of DESSO water extract. The water extracts of the
leaves of both weeds had the greatest inhibitory effects on
germination and primary growth of wheat, compared to those of
stems and roots. Increasing the concentration of water extract of
leaves, stems and roots of both weeds up to 8 % caused the greatest
inhibitory effects to wheat and reduced the germination rate and
primary growth of it linearly.
Abstract: With continuous rise of oil price, how to develop alternative energy source has become a hot topic around the world. This study discussed the dynamic characteristics of an island power system operating under random wind speed lower than nominal wind
speeds of wind turbines. The system primarily consists of three diesel engine power generation systems, three constant-speed variable-pitch wind turbines, a small hydraulic induction generation system, and lumped static loads. Detailed models based on Matlab/Simulink were developed to cater for the dynamic behavior of the system. The results suggested this island power system can operate stably in this operational mode. This study can serve as an important reference for planning, operation, and further expansion of island power systems.
Abstract: For micro-gyroscopes, the angular rate detection components have to oscillate forwards and backwards alternatively. An innovative design of micro-electromagnetic drive module is proposed to make a Π-type disc reciprocally and efficiently rotate within a certain of angular interval. Twelve Electromagnetic poles enclosing the thin disc are designed to provide the magnetic drive power. Isotropic etching technique is employed to fabricate the high-aspect-ratio trench, so that the contact angle of wire against trench can be increased and the potential defect of cavities and pores within the wire can be prevented. On the other hand, a Π-type thin disc is designed to conduct the pitch motion as an angular excitation, in addition to spinning, is exerted on the gyroscope. The efficacy of the micro-magnetic drive module is verified by the commercial software, Ansoft Maxewll. In comparison with the conventional planar windings in micro-scale systems, the magnetic drive force is increased by 150%.
Abstract: Research papers are usually evaluated via peer
review. However, peer review has limitations in evaluating research
papers. In this paper, Scienstein and the new idea of 'collaborative
document evaluation' are presented. Scienstein is a project to
evaluate scientific papers collaboratively based on ratings, links,
annotations and classifications by the scientific community using the
internet. In this paper, critical success factors of collaborative
document evaluation are analyzed. That is the scientists- motivation
to participate as reviewers, the reviewers- competence and the
reviewers- trustworthiness. It is shown that if these factors are
ensured, collaborative document evaluation may prove to be a more
objective, faster and less resource intensive approach to scientific
document evaluation in comparison to the classical peer review
process. It is shown that additional advantages exist as collaborative
document evaluation supports interdisciplinary work, allows
continuous post-publishing quality assessments and enables the
implementation of academic recommendation engines. In the long
term, it seems possible that collaborative document evaluation will
successively substitute peer review and decrease the need for
journals.
Abstract: This paper describes the results of an extensive study
and comparison of popular hash functions SHA-1, SHA-256,
RIPEMD-160 and RIPEMD-320 with JERIM-320, a 320-bit hash
function. The compression functions of hash functions like SHA-1
and SHA-256 are designed using serial successive iteration whereas
those like RIPEMD-160 and RIPEMD-320 are designed using two
parallel lines of message processing. JERIM-320 uses four parallel
lines of message processing resulting in higher level of security than
other hash functions at comparable speed and memory requirement.
The performance evaluation of these methods has been done by using
practical implementation and also by using step computation
methods. JERIM-320 proves to be secure and ensures the integrity of
messages at a higher degree. The focus of this work is to establish
JERIM-320 as an alternative of the present day hash functions for the
fast growing internet applications.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Existing proceeding-models for the development of mechatronic systems provide a largely parallel action in the detailed development. This parallel approach is to take place also largely independent of one another in the various disciplines involved. An approach for a new proceeding-model provides a further development of existing models to use for the development of Adaptronic Systems. This approach is based on an intermediate integration and an abstract modeling of the adaptronic system. Based on this system-model a simulation of the global system behavior, due to external and internal factors or Forces is developed. For the intermediate integration a special data management system is used. According to the presented approach this data management system has a number of functions that are not part of the "normal" PDM functionality. Therefore a concept for a new data management system for the development of Adaptive system is presented in this paper. This concept divides the functions into six layers. In the first layer a system model is created, which divides the adaptronic system based on its components and the various technical disciplines. Moreover, the parameters and properties of the system are modeled and linked together with the requirements and the system model. The modeled parameters and properties result in a network which is analyzed in the second layer. From this analysis necessary adjustments to individual components for specific manipulation of the system behavior can be determined. The third layer contains an automatic abstract simulation of the system behavior. This simulation is a precursor for network analysis and serves as a filter. By the network analysis and simulation changes to system components are examined and necessary adjustments to other components are calculated. The other layers of the concept treat the automatic calculation of system reliability, the "normal" PDM-functionality and the integration of discipline-specific data into the system model. A prototypical implementation of an appropriate data management with the addition of an automatic system development is being implemented using the data management system ENOVIA SmarTeam V5 and the simulation system MATLAB.
Abstract: Cassava bagasse is one of major biomass wastes in Thailand from starch processing industry, which contains high starch content of about 60%. The object of this study was to investigate the optimal condition for hydrothermally pretreating cassava baggasses with or without acid addition. The pretreated samples were measured reducing sugar yield directly or after enzymatic hydrolysis (alpha-amylase). In enzymatic hydrolysis, the highest reducing sugar content was obtained under hydrothermal conditions for at 125oC for 30 min. The result shows that pretreating cassava baggasses increased the efficiency of enzymatic hydrolysis. For acid hydrolysis, pretreating cassava baggasses with sulfuric acid at 120oC for 60 min gave a maximum reducing sugar yield. In this study, sulfuric acid had a greater capacity for hydrolyzing cassava baggasses than phosphoric acid. In comparison, dilute acid hydrolysis to provide a higher yield of reducing sugar than the enzymatic hydrolysis combined hydrothermal pretreatment. However, enzymatic hydrolysis in a combination with hydrothermal pretreatment was an alternative to enhance efficiency reducing sugar production from cassava bagasse.