Abstract: Stress-strain curve of inter-tube connected carbon nanotube (CNT) reinforced polymer composite under axial loading generated from molecular dynamics simulation is presented. Comparison of the response to axial mechanical loading between this composite system with composite systems reinforced by long, continuous CNTs (replicated via periodic boundary conditions) and short, discontinuous CNTs has been made. Simulation results showed that the inter-tube connection improved the mechanical properties of short discontinuous CNTs dramatically. Though still weaker than long CNT/polymer composite, more remarkable increase in the stiffness relative to the polymer was observed in the inter-tube connected CNT/polymer composite than in the discontinuous CNT/polymer composite. The manually introduced bridge break process resulted in a stress-strain curve of ductile fracture mode, which is consistent with the experimental result.
Abstract: The paper presents the results of microhardness and
microstructure of low carbon steel surface melted using carbon
dioxide laser with a wavelength of 10.6μm and a maximum output
power of 2000W. The processing parameters such as the laser power,
and the scanning rate were investigated in this study. After surface
melting two distinct regions formed corresponding to the melted zone
MZ, and the heat affected zone HAZ. The laser melted region
displayed a cellular fine structures while the HAZ displayed
martensite or bainite structure. At different processing parameters,
the original microstructure of this steel (Ferrite+Pearlite) has been
transformed to new phases of martensitic and bainitic structures. The
fine structure and the high microhardness are evidence of the high
cooling rates which follow the laser melting. The melting pool and
the transformed microstructure in the laser surface melted region of
carbon steel showed clear dependence on laser power and scanning
rate.
Abstract: Drop-in of R-22 alternatives in refrigeration and air conditioning systems requires a redesign of system components to improve system performance and reliability with the alternative refrigerants. The present paper aims at design adiabatic capillary tubes for R-22 alternatives such as R-417A, R-422D and R-438A. A theoretical model has been developed and validated with the available experimental data from literature for R-22 over a wide range of both operating and geometrical parameters. Predicted lengths of adiabatic capillary tube are compared with the lengths of the capillary tube needed under similar experimental conditions and majority of predictions are found to be within 4.4% of the experimental data. Hence, the model has been applied for R-417A, R- 422D and R-438A and capillary tube selection charts and correlations have been computed. Finally a comparison between the selected refrigerants and R-22 has been introduced and the results showed that R-438A is the closest one to R-22.
Abstract: The effect of the discontinuity of the rail ends and the
presence of lower modulus insulation material at the gap to the
variations of stresses in the insulated rail joint (IRJ) is presented. A
three-dimensional wheel – rail contact model in the finite element
framework is used for the analysis. It is shown that the maximum stress
occurs in the subsurface of the railhead when the wheel contact occurs
far away from the rail end and migrates to the railhead surface as the
wheel approaches the rail end; under this condition, the interface
between the rail ends and the insulation material has suffered
significantly increased levels of stress concentration. The ratio of the
elastic modulus of the railhead and insulation material is found to alter
the levels of stress concentration. Numerical result indicates that a
higher elastic modulus insulating material can reduce the stress
concentration in the railhead but will generate higher stresses in the
insulation material, leading to earlier failure of the insulation material
Abstract: Wireless Sensor Networks (WSNs) have attracted the attention of many researchers. This has resulted in their rapid integration in very different areas such as precision agriculture,environmental monitoring, object and event detection and military surveillance. Due to the current WSN characteristics this technology is specifically useful in industrial areas where security, reliability and autonomy are basic, such as nuclear power plants, chemical plants, and others. In this paper we present a system based on WSNs to monitor environmental conditions around and inside a nuclear power plant, specifically, radiation levels. Sensor nodes, equipped with radiation sensors, are deployed in fixed positions throughout the plant. In addition, plant staff are also equipped with mobile devices with higher capabilities than sensors such as for example PDAs able to monitor radiation levels and other conditions around them. The system enables communication between PDAs, which form a Mobile Ad-hoc Wireless Network (MANET), and allows workers to monitor remote conditions in the plant. It is particularly useful during stoppage periods for inspection or in the event of an accident to prevent risk situations.
Abstract: The purpose of this study is to investigate the chemical
degradation of the organophosphorus pesticide of parathion and
carbamate insecticide of methomyl in the aqueous phase through
Fenton process. With the employment of batch Fenton process, the
degradation of the two selected pesticides at different pH, initial
concentration, humic acid concentration, and Fenton reagent dosages
was explored. The Fenton process was found effective to degrade
parathion and methomyl. The optimal dosage of Fenton reagents (i.e.,
molar concentration ratio of H2O2 to Fe2+) at pH 7 for parathion
degradation was equal to 3, which resulted in 50% removal of
parathion. Similarly, the optimal dosage for methomyl degradation
was 1, resulting in 80% removal of methomyl. This study also found
that the presence of humic substances has enhanced pesticide
degradation by Fenton process significantly. The mass spectroscopy
results showed that the hydroxyl free radical may attack the single
bonds with least energy of investigated pesticides to form smaller
molecules which is more easily to degrade either through
physio-chemical or bilolgical processes.
Abstract: This paper investigates the relationship between state and business in the context of structural and institutional transformations in Indonesia following the collapse of the New Order regime in 1998. Since 1998, Indonesia has embarked on a shift from an authoritarian to democratic polity and from a centralised to a decentralised system of governance, transforming the country into the third largest democracy and one of the most decentralised states in the world. This paper examines whether the transformation of the Indonesian state has altered the pattern of state and business relations with focus on clientism and corruption as the key dependent variable, and probes how/to what extent this has changed as a result of the transformation and the ensuring shifts in business and state relations. Based on interviews with key government and business actors as well as prominent scholars in Indonesia, it is found that since the demise of the New Order, business associations in Indonesia have become more independent of state control and more influential in public decision-making whereas the government has become more responsive of business concerns and more committed to combat corruption and clientism. However, these changes have not necessarily rendered business people completely leave individualclientelistic relationship with the government, and simply pursue wider sectoral and business-wide collectivism as an alternative way of channelling their aspirations, which is expected to help reduce corruption and clientism in Indonesia. This paper concludes that democratisation and a more open politics may have helped reduce corruption and clientism in Indonesia through changes in government. However, it is still difficult to imply that such political transformation has fostered business collective action and a broader, more encompassing pattern of business lobbying and activism, which is expected to help reduce corruption and clientism.
Abstract: It can be said that the business sector is faced with a range of challenges–a rapidly changing business environment, an increase and diversification of customers- demands and the consequent need for quick response–for having in place flexible management and production info systems. As a matter of fact, many manufacturers have adopted production info management systems such as MES and ERP. Nevertheless, managers are having difficulties obtaining ever-changing production process information in real time, or responding quickly to any change in production related needs on the basis of such information. This is because they rely on poor production info systems which are not capable of providing real-time factory settings. If the manufacturer doesn-t have a capacity for collecting or digitalizing the 4 Ms (Man, Machine, Material, Method), which are resources for production, on a real time basis, it might to difficult to effectively maintain the information on production process. In this regard, this paper will introduce some new alternatives to the existing methods of collecting the 4 Ms in real time, which are currently comprise the production field.
Abstract: In this paper, we proposed the direct method for converting
Finite-Impulse Response (FIR) filter with low nonzero tap
into Infinite-Impulse Response (IIR) filter using the pre-determined
table. The prony method is used by ghost cancellator which is IIR
approximation to FIR filter which is better performance than IIR and
have much larger calculation difference. The direct method for many
ghost combination with low nonzero tap of NTSC(National Television
System Committee) TV signal in Korea is described. The proposed
method is illustrated with an example.
Abstract: We present a discussion of three adaptive filtering
algorithms well known for their one-step termination property, in
terms of their relationship with the minimal residual method. These
algorithms are the normalized least mean square (NLMS), Affine
Projection algorithm (APA) and the recursive least squares algorithm
(RLS). The NLMS is shown to be a result of the orthogonality
condition imposed on the instantaneous approximation of the Wiener
equation, while APA and RLS algorithm result from orthogonality
condition in multi-dimensional minimal residual formulation. Further
analysis of the minimal residual formulation for the RLS leads to
a triangular system which also possesses the one-step termination
property (in exact arithmetic)
Abstract: A kind of singularly perturbed boundary value problems is under consideration. In order to obtain its approximation, simple upwind difference discretization is applied. We use a moving mesh iterative algorithm based on equi-distributing of the arc-length function of the current computed piecewise linear solution. First, a maximum norm a posteriori error estimate on an arbitrary mesh is derived using a different method from the one carried out by Chen [Advances in Computational Mathematics, 24(1-4) (2006), 197-212.]. Then, basing on the properties of discrete Green-s function and the presented posteriori error estimate, we theoretically prove that the discrete solutions computed by the algorithm are first-order uniformly convergent with respect to the perturbation parameter ε.
Abstract: This paper highlights the importance of the selection
of the building-s wall material,and the shortcomings of the most
commonly used framed structures with masonry infills .The
objective of this study is investigating the behavior of infill walls as
structural components in existing structures.Structural infill walls are
very important in structural behavior under earthquake effects.
Structural capacity under the effect of earthquake,displacement and
relative story displacement are affected by the structural irregularities
.The presence of nonstructural masonry infill walls can modify
extensively the global seismic behavior of framed buildings .The
stability and integrity of reinforced concrete frames are enhanced by
masonry infill walls. Masonry infill walls alter displacement and
base shear of the frame as well. Short columns have great
importance during earthquakes,because their failure may lead to
additional structural failures and result in total building collapse.
Consequently the effects of short columns are considered in this
study.
Abstract: Sensor networks are often deployed in unattended
environments, thus leaving these networks vulnerable to false data
injection attacks in which an adversary injects forged reports into the
network through compromised nodes, with the goal of deceiving the
base station or depleting the resources of forwarding nodes. Several
research solutions have been recently proposed to detect and drop such
forged reports during the forwarding process. Each design can provide
the equivalent resilience in terms of node compromising. However,
their energy consumption characteristics differ from each other. Thus,
employing only a single filtering scheme for a network is not a
recommendable strategy in terms of energy saving. It's very important
the threshold determination for message authentication to identify. We
propose the recursive contract net protocols which less energy level of
terminal node in wireless sensor network.
Abstract: All over the world, including the Middle and East
European countries, sustainable tillage and sowing technologies are
applied increasingly broadly with a view to optimising soil resources,
mitigating soil degradation processes, saving energy resources,
preserving biological diversity, etc. As a result, altered conditions of
tillage and sowing technological processes are faced inevitably. The
purpose of this study is to determine the seedbed topsoil hardness
when using a combined sowing coulter in different sustainable tillage
technologies. The research involved a combined coulter consisting
of two dissected blade discs and a shoe coulter. In order to determine
soil hardness at the seedbed area, a multipenetrometer was used. It
was found by experimental studies that in loosened soil, a combined
sowing coulter equally suppresses the furrow bottom, walls and soil
near the furrow; therefore, here, soil hardness was similar at all
researched depths and no significant differences were established. In
loosened and compacted (double-rolled) soil, the impact of a
combined coulter on the hardness of seedbed soil surface was more
considerable at a depth of 2 mm. Soil hardness at the furrow bottom
and walls to a distance of up to 26 mm was 1.1 MPa. At a depth of 10
mm, the greatest hardness was established at the furrow bottom. In
loosened and heavily compacted (rolled for 6 times) soil, at a depth
of 2 and 10 mm a combined coulter most of all compacted the furrow
bottom, which has a hardness of 1.8 MPa. At a depth of 20 mm, soil
hardness within the whole investigated area varied insignificantly and
fluctuated by around 2.0 MPa. The hardness of furrow walls and soil
near the furrow was by approximately 1.0 MPa lower than that at the
furrow bottom
Abstract: This article presents the developments of efficient
algorithms for tablet copies comparison. Image recognition has
specialized use in digital systems such as medical imaging,
computer vision, defense, communication etc. Comparison between
two images that look indistinguishable is a formidable task. Two
images taken from different sources might look identical but due to
different digitizing properties they are not. Whereas small variation
in image information such as cropping, rotation, and slight
photometric alteration are unsuitable for based matching
techniques. In this paper we introduce different matching
algorithms designed to facilitate, for art centers, identifying real
painting images from fake ones. Different vision algorithms for
local image features are implemented using MATLAB. In this
framework a Table Comparison Computer Tool “TCCT" is
designed to facilitate our research. The TCCT is a Graphical Unit
Interface (GUI) tool used to identify images by its shapes and
objects. Parameter of vision system is fully accessible to user
through this graphical unit interface. And then for matching, it
applies different description technique that can identify exact
figures of objects.
Abstract: Stream Control Transmission Protocol (SCTP) has been
proposed to provide reliable transport of real-time communications.
Due to its attractive features, such as multi-streaming and multihoming,
the SCTP is often expected to be an alternative protocol
for TCP and UDP. In the original SCTP standard, the secondary path
is mainly regarded as a redundancy. Recently, most of researches
have focused on extending the SCTP to enable a host to send its
packets to a destination over multiple paths simultaneously. In order
to transfer packets concurrently over the multiple paths, the SCTP
should be well designed to avoid unnecessary fast retransmission
and the mis-estimation of congestion window size through the paths.
Therefore, we propose an Enhanced Cooperative ACK SCTP (ECASCTP)
to improve the path recovery efficiency of multi-homed host
which is under concurrent multiple transfer mode. We evaluated the
performance of our proposed scheme using ns-2 simulation in terms
of cwnd variation, path recovery time, and goodput. Our scheme
provides better performance in lossy and path asymmetric networks.
Abstract: This paper addresses the development of an intelligent vision system for human-robot interaction. The two novel contributions of this paper are 1) Detection of human faces and 2) Localizing the eye. The method is based on visual attributes of human skin colors and geometrical analysis of face skeleton. This paper introduces a spatial domain filtering method named ?Fuzzily skewed filter' which incorporates Fuzzy rules for deciding the gray level of pixels in the image in their neighborhoods and takes advantages of both the median and averaging filters. The effectiveness of the method has been justified over implementing the eye tracking commands to an entertainment robot, named ''AIBO''.
Abstract: To determine the length of engagement threads of a bolt installed in a tapped part in order to avoid the threads stripping remains a very current problem in the design of the thread assemblies. It does not exist a calculation method formalized for the cases where the bolt is screwed directly in a ductile material. In this article, we study the behavior of the threads stripping of a loaded assembly by using a modelling by finite elements and a rupture criterion by damage. This modelling enables us to study the different parameters likely to influence the behavior of this bolted connection. We study in particular, the influence of couple of materials constituting the connection, of the bolt-s diameter and the geometrical characteristics of the tapped part, like the external diameter and the length of engagement threads. We established an experiments design to know the most significant parameters. That enables us to propose a simple expression making possible to calculate the resistance of the threads whatever the metallic materials of the bolt and the tapped part. We carried out stripping tests in order to validate our model. The estimated results are very close to those obtained by the tests.
Abstract: Ireland developed a National Strategy 2030 that
argued for the creation of a new form of higher education institution,
a Technological University. The research reported here reviews the
first stage of this partnership development. The study found that
national policy can create system capacity and change, but that
individual partners may have more to gain or lose in collaborating.
When presented as a zero-sum activity, fear among partners is high.
The level of knowledge and networking within the higher education
system possessed by each partner contributed to decisions to
participate or not in a joint proposal for collaboration. Greater
success resulted when there were gains for all partners. This research
concludes that policy mandates can provide motivation to
collaborate, but that the partnership needs to be built more on shared
values versus coercion by mandates.
Abstract: In this paper, an innovative watermarking scheme for audio signal based on genetic algorithms (GA) in the discrete wavelet transforms is proposed. It is robust against watermarking attacks, which are commonly employed in literature. In addition, the watermarked image quality is also considered. We employ GA for the optimal localization and intensity of watermark. The watermark detection process can be performed without using the original audio signal. The experimental results demonstrate that watermark is inaudible and robust to many digital signal processing, such as cropping, low pass filter, additive noise.