Abstract: The problem of wastewater treatment in Egypt is a two-fold problem; the first part concerning the existing rural areas, the second one dealing with new industrial/domestic areas. In Egypt several agricultural projects have been initiated by the government and the private sector as well, in order to change its infrastructure. As a reliable energy source, photovoltaic pumping systems have contributed to supply water for local rural communities worldwide; they can also be implemented to solve the problem “wastewater environment pollution". The solution of this problem can be categorised as recycle process. In addition, because of regional conditions past technologies are being reexamined to select a smallscale treatment system requiring low construction and maintenance costs. This paper gives the design guidelines of a Photovoltaic Small- Scale Wastewater Treatment Plant (PVSSWTP) based on technologies that can be transferred.
Abstract: This paper proposes a new performance characterization for the test strategy intended for second order filters denominated Transient Analysis Method (TRAM). We evaluate the ability of the addressed test strategy for detecting deviation faults under simultaneous statistical fluctuation of the non-faulty parameters. For this purpose, we use Monte Carlo simulations and a fault model that considers as faulty only one component of the filter under test while the others components adopt random values (within their tolerance band) obtained from their statistical distributions. The new data reported here show (for the filters under study) the presence of hard-to-test components and relatively low fault coverage values for small deviation faults. These results suggest that the fault coverage value obtained using only nominal values for the non-faulty components (the traditional evaluation of TRAM) seem to be a poor predictor of the test performance.
Abstract: By the application of an improved back-propagation
neural network (BPNN), a model of current densities for a solid oxide
fuel cell (SOFC) with 10 layers is established in this study. To build
the learning data of BPNN, Taguchi orthogonal array is applied to
arrange the conditions of operating parameters, which totally 7 factors
act as the inputs of BPNN. Also, the average current densities
achieved by numerical method acts as the outputs of BPNN.
Comparing with the direct solution, the learning errors for all learning
data are smaller than 0.117%, and the predicting errors for 27
forecasting cases are less than 0.231%. The results show that the
presented model effectively builds a mathematical algorithm to predict
performance of a SOFC stack immediately in real time.
Also, the calculating algorithms are applied to proceed with the
optimization of the average current density for a SOFC stack. The
operating performance window of a SOFC stack is found to be
between 41137.11 and 53907.89. Furthermore, an inverse predicting
model of operating parameters of a SOFC stack is developed here by
the calculating algorithms of the improved BPNN, which is proved to
effectively predict operating parameters to achieve a desired
performance output of a SOFC stack.
Abstract: Molecular dynamics simulation of annular flow
boiling in a nanochannel with 70000 particles is numerically
investigated. In this research, an annular flow model is developed to
predict the superheated flow boiling heat transfer characteristics in a
nanochannel. To characterize the forced annular boiling flow in a
nanochannel, an external driving force F ext ranging from 1to12PN
(PN= Pico Newton) is applied along the flow direction to inlet fluid
particles during the simulation. Based on an annular flow model
analysis, it is found that saturation condition and superheat degree
have great influences on the liquid-vapor interface. Also, the results
show that due to the relatively strong influence of surface tension in
small channel, the interface between the liquid film and vapor core is
fairly smooth, and the mean velocity along the stream-wise direction
does not change anymore.
Abstract: The main goal of the study is to analyze all relevant
properties of the electro hydraulic systems and based on that to make
a proper choice of the control strategy that may be used for the
control of the servomechanism system. A combination of electronic
and hydraulic systems is widely used since it combines the
advantages of both. Hydraulic systems are widely spread because of
their properties as accuracy, flexibility, high horsepower-to-weight
ratio, fast starting, stopping and reversal with smoothness and
precision, and simplicity of operations. On the other hand, the
modern control of hydraulic systems is based on control of the circuit
fed to the inductive solenoid that controls the position of the
hydraulic valve. Since this circuit may be easily handled by PWM
(Pulse Width Modulation) signal with a proper frequency, the
combination of electrical and hydraulic systems became very fruitful
and usable in specific areas as airplane and military industry.
The study shows and discusses the experimental results obtained
by the control strategy (classical feedback (PID) & neural network)
using MATLAB and SIMULINK [1]. Finally, the special attention
was paid to the possibility of neuro-controller design and its
application to control of electro-hydraulic systems and to make
comparative with classical control.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: In the time of globalisation, growing uncertainty, ambiguity and change, traditional way of doing business are no longer sufficient and it is important to consider non-conventional methods and approaches to release creativity and facilitate innovation and growth. Thus, creative industries, as a natural source of creativity and innovation, draw particular attention. This paper explores feasibility of building creative partnerships between creative industries and business and brings attention to mutual benefits derived from such partnerships. Design/approach - This paper is a theoretical exploration of projects, practices and research findings addressing collaboration between creative industries and business. Thus, it concerns creative industries, arts, business and its representatives in order to define requirements for creative partnerships to work and succeed. Findings – Current practices in engaging into arts-business partnerships are still very few, although most of creative partnerships proved to be highly valuable and mutually beneficial. Certain conditions shall be provided in order to benefit from arts-business creative synergy. Originality/value- By integrating different sources of literature, this article provides a base for conducting empirical research in several dimensions within arts-business partnerships.
Abstract: In Public Wireless LANs(PWLANs), user anonymity
is an essential issue. Recently, Juang et al. proposed an anonymous
authentication and key exchange protocol using smart cards in
PWLANs. They claimed that their proposed scheme provided identity
privacy, mutual authentication, and half-forward secrecy. In this paper,
we point out that Juang et al.'s protocol is vulnerable to the
stolen-verifier attack and does not satisfy user anonymity.
Abstract: Traffic congestion has become a major problem in
many countries. One of the main causes of traffic congestion is due
to road merges. Vehicles tend to move slower when they reach the
merging point. In this paper, an enhanced algorithm for traffic
simulation based on the fluid-dynamic algorithm and kinematic wave
theory is proposed. The enhanced algorithm is used to study traffic
congestion at a road merge. This paper also describes the
development of a dynamic traffic simulation tool which is used as a
scenario planning and to forecast traffic congestion level in a certain
time based on defined parameter values. The tool incorporates the
enhanced algorithm as well as the two original algorithms. Output
from the three above mentioned algorithms are measured in terms of
traffic queue length, travel time and the total number of vehicles
passing through the merging point. This paper also suggests an
efficient way of reducing traffic congestion at a road merge by
analyzing the traffic queue length and travel time.
Abstract: Existing ground movement surveillance technologies
at airports are subjected to limitations due to shadowing effects or
multiple reflections. Therefore, there is a strong demand for a new
sensing technology, which will be cost effective and will provide
detection of non-cooperative targets under any weather conditions.
This paper aims to present a new intelligent system, developed
within the framework of the EC-funded ISMAEL project, which is
based on a new magnetic sensing technology and provides detection,
tracking and automatic classification of targets moving on the airport
surface. The system is currently being installed at two European
airports. Initial experimental results under real airport traffic
demonstrate the great potential of the proposed system.
Abstract: This paper presents a systematic approach for the
design of power system stabilizer using genetic algorithm and
investigates the robustness of the GA based PSS. The proposed
approach employs GA search for optimal setting of PSS parameters.
The performance of the proposed GPSS under small and large
disturbances, loading conditions and system parameters is tested.
The eigenvalue analysis and nonlinear simulation results show the
effectiveness of the GPSS to damp out the system oscillations. It is
found tat the dynamic performance with the GPSS shows improved
results, over conventionally tuned PSS over a wide range of
operating conditions.
Abstract: In this paper a new embedded Singly Diagonally
Implicit Runge-Kutta Nystrom fourth order in fifth order method for
solving special second order initial value problems is derived. A
standard set of test problems are tested upon and comparisons on the
numerical results are made when the same set of test problems are
reduced to first order systems and solved using the existing
embedded diagonally implicit Runge-Kutta method. The results
suggests the superiority of the new method.
Abstract: Wireless Sensor Networks (WSN) are emerging
because of the developments in wireless communication technology and miniaturization of the hardware. WSN consists of a large number of low-cost, low-power, multifunctional sensor nodes to monitor physical conditions, such as temperature, sound, vibration, pressure,
motion, etc. The MAC protocol to be used in the sensor networks must be energy efficient and this should aim at conserving the energy during its operation. In this paper, with the focus of analyzing the
MAC protocols used in wireless Adhoc networks to WSN, simulation
experiments were conducted in Global Mobile Simulator
(GloMoSim) software. Number of packets sent by regular nodes, and received by sink node in different deployment strategies, total energy
spent, and the network life time have been chosen as the metric for comparison. From the results of simulation, it is evident that the IEEE 802.11 protocol performs better compared to CSMA and MACA protocols.
Abstract: The proof of concept experiments were conducted to
determine the feasibility of using small amounts of Dissolved
Sulphur (DS) from the gaseous phase to precipitate platinum ions in
chloride media. Two sets of precipitation experiments were
performed in which the source of sulphur atoms was either a
thiosulphate solution (Na2S2O3) or a sulphur dioxide gas (SO2). In
liquid-liquid (L-L) system, complete precipitation of Pt was achieved
at small dosages of Na2S2O3 (0.01 – 1.0 M) in a time interval of 3-5
minutes. On the basis of this result, gas absorption tests were carried
out mainly to achieve sulphur solubility equivalent to 0.018 M. The
idea that huge amounts of precious metals could be recovered
selectively from their dilute solutions by utilizing the waste SO2
streams at low pressure seemed attractive from the economic and
environmental point of views. Therefore, mass transfer characteristics
of SO2 gas associated with reactive absorption across the gas-liquid
(G-L) interface were evaluated under different conditions of pressure
(0.5 – 2 bar), solution temperature ranges from 20 – 50 oC and acid
strength (1 – 4 M, HCl). This paper concludes with information about
selective precipitation of Pt in the presence of cations (Fe2+, Co2+,
and Cr3+) in a CSTR and recommendation to scale up laboratory data
to industrial pilot scale operations.
Abstract: The aeration process via injectors is used to combat
the lack of oxygen in lakes due to eutrophication. A 3D numerical
simulation of the resulting flow using a simplified model is presented.
In order to generate the best dynamic in the fluid with respect to
the aeration purpose, the optimization of the injectors location is
considered. We propose to adapt to this problem the topological
sensitivity analysis method which gives the variation of a criterion
with respect to the creation of a small hole in the domain. The main
idea is to derive the topological sensitivity analysis of the physical
model with respect to the insertion of an injector in the fluid flow
domain. We propose in this work a topological optimization algorithm
based on the studied asymptotic expansion. Finally we present some
numerical results, showing the efficiency of our approach
Abstract: In process control applications, above 90% of the
controllers are of PID type. This paper proposed a robust PI
controller with fractional-order integrator. The PI parameters were
obtained using classical Ziegler-Nichols rules but enhanced with the
application of error filter cascaded to the fractional-order PI. The
controller was applied on steam temperature process that was
described by FOPDT transfer function. The process can be classified
as lag dominating process with very small relative dead-time. The
proposed control scheme was compared with other PI controller
tuned using Ziegler-Nichols and AMIGO rules. Other PI controller
with fractional-order integrator known as F-MIGO was also
considered. All the controllers were subjected to set point change and
load disturbance tests. The performance was measured using Integral
of Squared Error (ISE) and Integral of Control Signal (ICO). The
proposed controller produced best performance for all the tests with
the least ISE index.
Abstract: In this paper, a pipelined version of genetic algorithm,
called PLGA, and a corresponding hardware platform are described.
The basic operations of conventional GA (CGA) are made pipelined
using an appropriate selection scheme. The selection operator, used
here, is stochastic in nature and is called SA-selection. This helps
maintaining the basic generational nature of the proposed pipelined
GA (PLGA). A number of benchmark problems are used to compare
the performances of conventional roulette-wheel selection and the
SA-selection. These include unimodal and multimodal functions with
dimensionality varying from very small to very large. It is seen that
the SA-selection scheme is giving comparable performances with
respect to the classical roulette-wheel selection scheme, for all the
instances, when quality of solutions and rate of convergence are considered.
The speedups obtained by PLGA for different benchmarks
are found to be significant. It is shown that a complete hardware
pipeline can be developed using the proposed scheme, if parallel
evaluation of the fitness expression is possible. In this connection
a low-cost but very fast hardware evaluation unit is described.
Results of simulation experiments show that in a pipelined hardware
environment, PLGA will be much faster than CGA. In terms of
efficiency, PLGA is found to outperform parallel GA (PGA) also.
Abstract: The paper deals with calculation of the parameters of
ceramic material from a set of destruction tests of ceramic heads of
total hip joint endoprosthesis. The standard way of calculation of the
material parameters consists in carrying out a set of 3 or 4 point
bending tests of specimens cut out from parts of the ceramic material
to be analysed. In case of ceramic heads, it is not possible to cut out
specimens of required dimensions because the heads are too small (if
the cut out specimens were smaller than the normalised ones, the
material parameters derived from them would exhibit higher strength
values than those which the given ceramic material really has). On
that score, a special testing jig was made, in which 40 heads were
destructed. From the measured values of circumferential strains of the
head-s external spherical surface under destruction, the state of stress
in the head under destruction was established using the final elements
method (FEM). From the values obtained, the sought for parameters
of the ceramic material were calculated using Weibull-s weakest-link
theory.
Abstract: This is a study on numerical simulation of the convection-diffusion transport of a chemical species in steady flow through a small-diameter tube, which is lined with a very thin layer made up of retentive and absorptive materials. The species may be subject to a first-order kinetic reversible phase exchange with the wall material and irreversible absorption into the tube wall. Owing to the velocity shear across the tube section, the chemical species may spread out axially along the tube at a rate much larger than that given by the molecular diffusion; this process is known as dispersion. While the long-time dispersion behavior, well described by the Taylor model, has been extensively studied in the literature, the early development of the dispersion process is by contrast much less investigated. By early development, that means a span of time, after the release of the chemical into the flow, that is shorter than or comparable to the diffusion time scale across the tube section. To understand the early development of the dispersion, the governing equations along with the reactive boundary conditions are solved numerically using the Flux Corrected Transport Algorithm (FCTA). The computation has enabled us to investigate the combined effects on the early development of the dispersion coefficient due to the reversible and irreversible wall reactions. One of the results is shown that the dispersion coefficient may approach its steady-state limit in a short time under the following conditions: (i) a high value of Damkohler number (say Da ≥ 10); (ii) a small but non-zero value of absorption rate (say Γ* ≤ 0.5).
Abstract: The objective of this research is parameters optimized
of the stair shape workpiece which is cut by CNC Wire-Cut EDM
(WEDW). The experiment material is SKD-11 steel of stair-shaped
with variable height workpiece 10, 20, 30 and 40 mm. with the same
10 mm. thickness are cut by Sodick's CNC Wire-Cut EDM model
AD325L.
The experiments are designed by 3k full factorial experimental
design at 3 level 2 factors and 9 experiments with 2 replicate. The
selected two factor are servo voltage (SV) and servo feed rate (SF)
and the response is cutting thickness error. The experiment is divided
in two experiments. The first experiment determines the significant
effective factor at confidential interval 95%. The SV factor is the
significant effective factor from first result. In order to result smallest
cutting thickness error of workpieces is 17 micron with the SV value
is 46 volt. Also show that the lower SV value, the smaller different
thickness error of workpiece. Then the second experiment is done to
reduce different cutting thickness error of workpiece as small as
possible by lower SV. The second experiment result show the
significant effective factor at confidential interval 95% is the SV
factor and the smallest cutting thickness error of workpieces reduce
to 11 micron with the experiment SV value is 36 volt.