Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: The effect of wood vinegar, entomopathogenic
nematodes ((Steinernema thailandensis n. sp.) and fermented organic
substances from four plants such as: Derris elliptica Roxb, Stemona
tuberosa Lour, Tinospora crispa Mier and Azadirachta indica J. were
tested on the five varieties of sweetpotato with potential for
bioethanol production ie. Taiwan, China, PROC No.65-16, Phichit
166-5, and Phichit 129-6. The experimental plots were located at
Faculty of Agriculture, Natural Resources and Environment,
Naresuan University, Phitsanulok, Thailand. The aim of this study
was to compare the efficiency of the five treatments for growth, yield
and insect infestation on the five varieties of sweetpotato. Treatment
with entomopathogenic nematodes gave the highest average weight
of sweetpotato tubers (1.3 kg/tuber), followed by wood vinegar,
fermented organic substances and mixed treatment with yields of
0.88, 0.46 and 0.43 kg/tuber, respectively. Also the
entomopathogenic nematode treatment gave significantly higher
average width and length of sweet potato (9.82 cm and 9.45 cm,
respectively). Additionally, the entomopathogenic nematode
provided the best control of insect infestation on sweetpotato leaves
and tubers. Comparison among the varieties of sweetpotato, PROC
NO.65-16 showed the highest weight and length. However, Phichit
129-6 gave significantly higher weight of 0.94 kg/tuber. Lastly, the
lowest sweet potato weevil infestation on leaves and tubers occurred
on Taiwan and Phichit 129-6.
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: This work deals with modeling and simulation of SO2 removal in a ceramic membrane by means of FEM. A mass transfer model was developed to predict the performance of SO2 absorption in a chemical solvent. The model was based on solving conservation equations for gas component in the membrane. Computational fluid dynamics (CFD) of mass and momentum were used to solve the model equations. The simulations aimed to obtain the distribution of gas concentration in the absorption process. The effect of the operating parameters on the efficiency of the ceramic membrane was evaluated. The modeling findings showed that the gas phase velocity has significant effect on the removal of gas whereas the liquid phase does not affect the SO2 removal significantly. It is also indicated that the main mass transfer resistance is placed in the membrane and gas phase because of high tortuosity of the ceramic membrane.
Abstract: This paper aims to present the reviews of the
application of neural network in shunt active power filter (SAPF).
From the review, three out of four components of SAPF structure,
which are harmonic detection component, compensating current
control, and DC bus voltage control, have been adopted some of
neural network architecture as part of its component or even
substitution. The objectives of most papers in using neural network in
SAPF are to increase the efficiency, stability, accuracy, robustness,
tracking ability of the systems of each component. Moreover,
minimizing unneeded signal due to the distortion is the ultimate goal
in applying neural network to the SAPF. The most famous
architecture of neural network in SAPF applications are ADALINE
and Backpropagation (BP).
Abstract: An aqueous methanol sensor for use in direct
methanol fuel cells (DMFCs) applications is demonstrated; the
methanol sensor is built using dispersed single-walled carbon
nanotubes (SWCNTs) with Nafion117 solution to detect the methanol
concentration in water. The study is aimed at the potential use of the
carbon nanotubes array as a methanol sensor for direct methanol fuel
cells (DMFCs). The concentration of methanol in the fuel circulation
loop of a DMFC system is an important operating parameter, because
it determines the electrical performance and efficiency of the fuel cell
system. The sensor is also operative even at ambient temperatures
and responds quickly to changes in the concentration levels of the
methanol. Such a sensor can be easily incorporated into the methanol
fuel solution flow loop in the DMFC system.
Abstract: Simultaneous recovery of copper and DCA from
simulated MEUF concentrated stream was investigated. Effects of
surfactant (DCA) and metal (copper) concentrations, surfactant to
metal molar ratio (S/M ratio), electroplating voltage, EDTA
concentration, solution pH, and salt concentration on metal recovery
and current efficiency were studied. Electric voltage of -0.5 V was
shown to be optimum operation condition in terms of Cu recovery,
current efficiency, and surfactant recovery. Increasing Cu recovery and
current efficiency were observed with increases of Cu concentration
while keeping concentration of DCA constant. However, increasing
both Cu and DCA concentration while keeping S/M ratio constant at
2.5 showed detrimental effect on Cu recovery at DCA concentration
higher than 15 mM. Cu recovery decreases with increasing pH while
current efficiency showed an opposite trend. It is believed that
conductivity is the main cause for discrepancy of Cu recovery and
current efficiency observed at different pH. Finally, it was shown that
EDTA had adverse effect on both Cu recovery and current efficiency
while addition of NaCl salt had negative impact on current efficiency
at concentration higher than 8000 mg/L.
Abstract: With the exponential growth of networked system and
application such as eCommerce, the demand for effective internet
security is increasing. Cryptology is the science and study of systems
for secret communication. It consists of two complementary fields of
study: cryptography and cryptanalysis. The application of genetic
algorithms in the cryptanalysis of knapsack ciphers is suggested by
Spillman [7]. In order to improve the efficiency of genetic algorithm
attack on knapsack cipher, the previously published attack was
enhanced and re-implemented with variation of initial assumptions
and results are compared with Spillman results. The experimental
result of research indicates that the efficiency of genetic algorithm
attack on knapsack cipher can be improved with variation of initial
assumption.
Abstract: Fisheries management all around the world is
hampered by the lack, or poor quality, of critical data on fish
resources and fishing operations. The main reasons for the chronic
inability to collect good quality data during fishing operations is the
culture of secrecy common among fishers and the lack of modern
data gathering technology onboard most fishing vessels. In response,
OLRAC-SPS, a South African company, developed fisheries datalogging
software (eLog in short) and named it Olrac. The Olrac eLog
solution is capable of collecting, analysing, plotting, mapping,
reporting, tracing and transmitting all data related to fishing
operations. Olrac can be used by skippers, fleet/company managers,
offshore mariculture farmers, scientists, observers, compliance
inspectors and fisheries management authorities. The authors believe
that using eLog onboard fishing vessels has the potential to
revolutionise the entire process of data collection and reporting
during fishing operations and, if properly deployed and utilised,
could transform the entire commercial fleet to a provider of good
quality data and forever change the way fish resources are managed.
In addition it will make it possible to trace catches back to the actual
individual fishing operation, to improve fishing efficiency and to
dramatically improve control of fishing operations and enforcement
of fishing regulations.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.
Abstract: In this paper we discuss the effect of unbounded particle interaction operator on particle growth and we study how this can address the choice of appropriate time steps of the numerical simulation. We provide also rigorous mathematical proofs showing that large particles become dominating with increasing time while small particles contribute negligibly. Second, we discuss the efficiency of the algorithm by performing numerical simulations tests and by comparing the simulated solutions with some known analytic solutions to the Smoluchowski equation.
Abstract: Ontology is widely being used as a tool for organizing
information, creating the relation between the subjects within the
defined knowledge domain area. Various fields such as Civil,
Biology, and Management have successful integrated ontology in
decision support systems for managing domain knowledge and to
assist their decision makers. Gross pollutant traps (GPT) are devices
used in trapping and preventing large items or hazardous particles in
polluting and entering our waterways. However choosing and
determining GPT is a challenge in Malaysia as there are inadequate
GPT data repositories being captured and shared. Hence ontology is
needed to capture, organize and represent this knowledge into
meaningful information which can be contributed to the efficiency of
GPT selection in Malaysia urbanization. A GPT Ontology framework
is therefore built as the first step to capture GPT knowledge which
will then be integrated into the decision support system. This paper
will provide several examples of the GPT ontology, and explain how
it is constructed by using the Protégé tool.
Abstract: From an economic standpoint the current and future
road traffic situation in urban areas is a cost factor. Traffic jams and
congestion prolong journey times and tie up resources in trucks and
personnel. Many discussions about imposing charges or tolls for
cities in Europe in order to reduce traffic congestion are currently in
progress. Both of these effects lead – directly or indirectly - to
additional costs for the urban distribution systems in retail
companies. One approach towards improving the efficiency of retail
distribution systems, and thus towards avoiding negative
environmental factors in urban areas, is horizontal collaboration for
deliveries to retail outlets – Urban Retail Logistics. This paper
presents a classification system to help reveal where cooperation
between retail companies is possible and makes sense for deliveries
to retail outlets in urban areas.
Abstract: This paper presents a new classification algorithm using colour and texture for obstacle detection. Colour information is computationally cheap to learn and process. However in many cases, colour alone does not provide enough information for classification. Texture information can improve classification performance but usually comes at an expensive cost. Our algorithm uses both colour and texture features but texture is only needed when colour is unreliable. During the training stage, texture features are learned specifically to improve the performance of a colour classifier. The algorithm learns a set of simple texture features and only the most effective features are used in the classification stage. Therefore our algorithm has a very good classification rate while is still fast enough to run on a limited computer platform. The proposed algorithm was tested with a challenging outdoor image set. Test result shows the algorithm achieves a much better trade-off between classification performance and efficiency than a typical colour classifier.
Abstract: This paper mathematically analyses the varying
magnitude of production loss, which may occur due to idle time (inprocess
waiting time and traveling time) on a linear walking worker
assembly line. Within this flexible and reconfigurable assembly
system, each worker travels down the line carrying out each
assembly task at each station; and each worker accomplishes the
assembly of a unit from start to finish and then travels back to the
first station to start the assembly of a new product. This strategy of
system design attempts to combine the flexibility of the U-shaped
moving worker assembly cell with the efficiency of the conventional
fixed worker assembly line. The paper aims to evaluate the effect of
idle time that may offset the labor efficiency of each walking worker
providing an insight into the mechanism of such a flexible and
reconfigurable assembly system.
Abstract: This study examines the structural and systematic processes of the Human Resources Division at The University of the West Indies, St. Augustine, Trinidad and Tobago for evidence of incorporation of the University's 2012- 2017 Strategic Plan. In conducting the study the structure of the Human Resources Management Division and its functions were carefully reviewed and measured against the strategic direction of the organisation. Findings indicate disconnect between these areas as there is apparent failure of the Human Resources Division to totally align its mandate with that of the organisation-s strategic direction. This action serves to threaten the viability of the organisation and its efficiency and effectiveness as an institution. The recommendations being put forward are for the realignment of the Human Resources Management Division and for its focus to mirror that of the organisation and the organisation-s goals and objectives. This may entail a restructuring of the Division.
Abstract: The deterministic quantum transfer-matrix (QTM)
technique and its mathematical background are presented. This
important tool in computational physics can be applied to a class of
the real physical low-dimensional magnetic systems described by the
Heisenberg hamiltonian which includes the macroscopic molecularbased
spin chains, small size magnetic clusters embedded in some
supramolecules and other interesting compounds. Using QTM, the
spin degrees of freedom are accurately taken into account, yielding
the thermodynamical functions at finite temperatures.
In order to test the application for the susceptibility calculations to
run in the parallel environment, the speed-up and efficiency of
parallelization are analyzed on our platform SGI Origin 3800 with
p = 128 processor units. Using Message Parallel Interface (MPI)
system libraries we find the efficiency of the code of 94% for
p = 128 that makes our application highly scalable.
Abstract: This paper proposes a Fuzzy Sliding Mode Control (FSMC) as a control strategy for Buck-Boost DC-DC converter. The proposed fuzzy controller specifies changes in the control signal based on the knowledge of the surface and the surface change to satisfy the sliding mode stability and attraction conditions. The performances of the proposed fuzzy sliding controller are compared to those obtained by a classical sliding mode controller. The satisfactory simulation results show the efficiency of the proposed control law which reduces the chattering phenomenon. Moreover, the obtained results prove the robustness of the proposed control law against variation of the load resistance and the input voltage of the studied converter.
Abstract: Mature landfill leachates contain some macromolecular organic substances that are resistant to biological degradation. Recently, Fenton-s oxidation has been investigated for chemical treatment or pre-treatment of mature landfill leachates. The aim of this study was to reduce the recalcitrant organic load still remaining after the complete treatment of a mature landfill leachate by Fenton-s oxidation post-treatment. The effect of various parameters such as H2O2 to Fe2+ molar ratio, dosage of Fe2+ reagent, initial pH, reaction time and initial chemical oxygen demand (COD) strength, that have an important role on the oxidation, was analysed. A molar ratio H2O2/Fe2+ = 3, a Fe2+ dosage of 4 mmol·L-1, pH 3, and a reaction time of 40 min were found to achieve better oxidation performances. At these favorable conditions, COD removal efficiency was 60.9% and 31.1% for initial COD of 93 and 743 mg·L-1 respectively (diluted and non diluted leachate). Fenton-s oxidation also presented good results for color removal. In spite of being extremely difficult to treat this leachate, the above results seem rather encouraging on the application of Fenton-s oxidation.