Abstract: Oxygen transfer, the process by which oxygen is
transferred from the gaseous to liquid phase, is a vital part of the
waste water treatment process. Because of low solubility of
oxygen and consequent low rate of oxygen transfer, sufficient
oxygen to meet the requirement of aerobic waste does not enter
through normal surface air water interface. Many theories have
come up in explaining the mechanism of gas transfer and
absorption of non-reacting gases in a liquid, of out of which, Two
film theory is important. An exiting mathematical model
determines approximate value of Overall Gas Transfer coefficient.
The Overall Gas Transfer coefficient, in case of Penetration theory,
is 1.13 time more than that obtained in case of Two film theory.
The difference is due to the difference in assumptions in the two
theories.
The paper aims at development of mathematical model which
determines the value of Overall Gas Transfer coefficient with
greater accuracy than the existing model.
Abstract: An experiment was conducted using two aeration
methods (water-into-air and air-into-water) and followed by filtration
processes using manganese greensand material. The properties of
groundwater such as pH, dissolved oxygen, turbidity and heavy metal
concentration (iron and manganese) will be assessed. The objectives
of this study are i) to determine the effective aeration method and ii)
to assess the effectiveness of manganese greensand as filter media in
removing iron and manganese concentration in groundwater. Results
showed that final pH for all samples after treatment are in range from
7.40 and 8.40. Both aeration methods increased the dissolved oxygen
content. Final turbidity for groundwater samples are between 3 NTU
to 29 NTU. Only three out of eight samples achieved iron
concentration of 0.3mg/L and less and all samples reach manganese
concentration of 0.1mg/L and less. Air-into-water aeration method
gives higher percentage of iron and manganese removal compare to
water-into-air method.
Abstract: This study examines the relationships between foreign
aid, levels of schooling and democracy for Pakistan using the ARDL
cointegration approach. The results of study provide strong evidence
for fairly robust long run as well as short run relationships among
these variables for the period 1973-2008. The results state that
foreign aid and primary school enrollments have negative impact on
democracy index and high school enrollments have positive impact
on democracy index in Pakistan. The study suggests for promotion of
education levels and relies on local resources instead of foreign aid
for a good quality of political institutions in Pakistan.
Abstract: An attempt was made for availability of wastewater reuse/reclamation for irrigation purposes using phytoremediation “the low cost and less technology", using six local aquatic macrophytes “e.g. T. angustifolia, B. maritimus, Ph. australis, A. donax, A. plantago-aquatica and M. longifolia (Linn)" as biological waste purifiers. Outdoor experiments/designs were conducted from May 03, 2007 till October 15, 2008, close to one of the main sewage channels of Sulaimani City/Iraq*. All processes were mainly based on conventional wastewater treatment processes, besides two further modifications were tested, the first was sand filtration pots, implanted by individual species of experimental macrophytes and the second was constructed wetlands implanted by experimental macrophytes all together. Untreated and treated wastewater samples were analyzed for their key physico-chemical properties (only heavy metals Fe, Mn, Zn and Cu with particular reference to removal efficiency by experimental macrophytes are highlighted in this paper). On the other hand, vertical contents of heavy metals were also evaluated from both pots and the cells of constructed wetland. After 135 days, macrophytes were harvested and heavy metals were analyzed in their biomass (roots/shoots) for removal efficiency assessment (i.e. uptake/ bioaccumulation rate). Results showed that; removal efficiency of all studied heavy metals was much higher in T. angustifolia followed by Ph. Australis, B. maritimus and A. donax in triple experiment sand pots. Constructed wetland experiments have revealed that; the more replicated constructed wetland cells the highest heavy metal removal efficiency was indicated.
Abstract: In this paper, the concepts of dichotomous logistic
regression (DLR) with leave-one-out (L-O-O) were discussed. To
illustrate this, the L-O-O was run to determine the importance of the
simulation conditions for robust test of spread procedures with good
Type I error rates. The resultant model was then evaluated. The
discussions included 1) assessment of the accuracy of the model, and
2) parameter estimates. These were presented and illustrated by
modeling the relationship between the dichotomous dependent
variable (Type I error rates) with a set of independent variables (the
simulation conditions). The base SAS software containing PROC
LOGISTIC and DATA step functions can be making used to do the
DLR analysis.
Abstract: Higher education institutions are increasingly opting to outsourcing methods in order to sustain themselves and this creates a gap of literature in terms of how they perceive the relationship. This research paper attempts to identify the behavioral and psychological factors that exist in the engagement thus providing valuable information to practicing and potential clients, and vendors. The determinants were gathered from previous literatures and analyzed to formulate the factors. This study adopts the case study and survey approaches in which interviews and questionnaires are deployed on employees of IT-related department in a Malaysian higher education institution.
Abstract: Since hyaluronic acid (HA) receptor such as CD44 is
over-expressed at sites of cancer cells, HA can be used as a targeting
vehicles for anti-cancer drugs. The aim of this study is to synthesize
block copolymer composed of hyaluronic acid and
poly(ε-caprolactone) (HAPCL) and to fabricate polymeric micelles for
anticancer drug targeting against CD44 receptor of tumor cells.
Chemical composition of HAPCL was confirmed using 1H NMR
spectroscopy. Doxorubicin (DOX) was incorporated into polymeric
micelles of HAPCL. The diameters of HAPHS polymeric micelles
were changed around 80nm and have spherical shapes. Targeting
potential was investigated using CD44-overexpressing. When
DOX-incorporated polymeric micelles was added to KB cells, they
revealed strong red fluorescence color while blocking of CD44
receptor by pretreatment of free HA resulted in reduced intensity,
indicating that HAPCL polymeric micelles have targetability against
CD44 receptor.
Abstract: The optimal grid spacing and turbulence model for the
2D numerical analysis of a vertical-axis water turbine (VAWaterT)
operating in a 2 m/s freestream current has been investigated. The
results of five different spatial domain discretizations and two
turbulence models (k-ω SST and k-ε RNG) have been compared, in
order to gain the optimal y+ parameter distribution along the blade
walls during a full rotor revolution. The resulting optimal mesh has
appeared to be quite similar to that obtained for the numerical
analysis of a vertical-axis wind turbine.
Abstract: Mobile Ad hoc networks (MANETs) are collections
of wireless mobile nodes dynamically reconfiguring and collectively
forming a temporary network. These types of networks assume
existence of no fixed infrastructure and are often useful in battle-field
tactical operations or emergency search-and-rescue type of
operations where fixed infrastructure is neither feasible nor practical.
They also find use in ad hoc conferences, campus networks and
commercial recreational applications carrying multimedia traffic. All
of the above applications of MANETs require guaranteed levels of
performance as experienced by the end-user. This paper focuses on
key challenges in provisioning predetermined levels of such Quality
of Service (QoS). It also identifies functional areas where QoS
models are currently defined and used. Evolving functional areas
where performance and QoS provisioning may be applied are also
identified and some suggestions are provided for further research in
this area. Although each of the above functional areas have been
discussed separately in recent research studies, since these QoS
functional areas are highly correlated and interdependent, a
comprehensive and comparative analysis of these areas and their
interrelationships is desired. In this paper we have attempted to
provide such an overview.
Abstract: Selective harmonic elimination-pulse width modulation techniques offer a tight control of the harmonic spectrum of a given voltage waveform generated by a power electronic converter along with a low number of switching transitions. Traditional optimization methods suffer from various drawbacks, such as prolonged and tedious computational steps and convergence to local optima; thus, the more the number of harmonics to be eliminated, the larger the computational complexity and time. This paper presents a novel method for output voltage harmonic elimination and voltage control of PWM AC/AC voltage converters using the principle of hybrid Real-Coded Genetic Algorithm-Pattern Search (RGA-PS) method. RGA is the primary optimizer exploiting its global search capabilities, PS is then employed to fine tune the best solution provided by RGA in each evolution. The proposed method enables linear control of the fundamental component of the output voltage and complete elimination of its harmonic contents up to a specified order. Theoretical studies have been carried out to show the effectiveness and robustness of the proposed method of selective harmonic elimination. Theoretical results are validated through simulation studies using PSIM software package.
Abstract: A new generation product made from bamboo strips,
known as laminated bamboo, has gained importance. The objective
of this research was to experiment the effect of three factors on the
mechanical property of laminated bamboo. The interested factors for
experimental design were (A) four bamboo species, namely Bambusa
blumeana Schultes (Pai See Suk), Dendrocalamus asper Backer (Pai
Tong), Dendrocalamus hamiltonii Nees (Pai Hok) and
Dendrocalamus sericeus Munro (Pai Sang Mon), (B) two types of
glue adhesive, polyvinyl acetate emulsion (PVAC) fortified with
urea-formaldehyde (UF) and urea-formaldehyde (UF) to make
parallel-oriented bamboo strips laminates and (C) glue weight per
strip area, 150 g/m2 and 190 g/m2. Experimental results showed that
Dendrocalamus asper Backer (Pai Tong) and Dendrocalamus
sericeus Munro (Pai Sang Mon) were best used for manufacturing
due to their highest MOR and MOE. The amount of glue weight 150
g/m2 yielded higher MOR and MOE than the amount of glue weight
190 g/m2. At the conclusion, the laminated bamboo manufacturers
can benefit from this research in order to select right materials
according to strength, cost and accessibility.
Abstract: The excellent suitability of the externally excited synchronous
machine (EESM) in automotive traction drive applications
is justified by its high efficiency over the whole operation range and
the high availability of materials. Usually, maximum efficiency is
obtained by modelling each single loss and minimizing the sum of all
losses. As a result, the quality of the optimization highly depends on
the precision of the model. Moreover, it requires accurate knowledge
of the saturation dependent machine inductances. Therefore, the
present contribution proposes a method to minimize the overall losses
of a salient pole EESM and its inverter in steady state operation based
on measurement data only. Since this method does not require any
manufacturer data, it is well suited for an automated measurement
data evaluation and inverter parametrization. The field oriented control
(FOC) of an EESM provides three current components resp. three
degrees of freedom (DOF). An analytic minimization of the copper
losses in the stator and the rotor (assuming constant inductances) is
performed and serves as a first approximation of how to choose the
optimal current reference values. After a numeric offline minimization
of the overall losses based on measurement data the results are
compared to a control strategy that satisfies cos (ϕ) = 1.
Abstract: Stocking density is considered one of the important
factors affecting fish growth. But, information related to impact of
stocking density on growth performance of monosex tilapia population
under the ecological conditions of Gangetic plains in West Bengal,
India is limited. The aim of our study was to compare the growth
potential of monosex tilapia at various stocking densities and to
determine an ideal stocking density for culture of all-male monosex
fish. The males were isolated by examination of genital papilla region
and were stocked separately in 0.01 ha earthen ponds at different
stocking densities (5000, 10000, 15000, 20000, 25000 and 30000
fingerlings/ha). It was found that the highest weight, length, daily
weight gain, growth rate and protein content were observed for the
20000 fish/ha density class. Thus, culture of monosex tilapia at a
density of 20000 fish/ha can be considered ideal for augmented
production of the fish under Indian context.
Abstract: This paper proposes the stochastic tabu search (STS)
for improving the measurement scheme for power system state
estimation. If the original measured scheme is not observable, the
additional measurements with minimum number of measurements are
added into the system by STS so that there is no critical measurement
pair. The random bit flipping and bit exchanging perturbations are
used for generating the neighborhood solutions in STS. The Pδ
observable concept is used to determine the network observability.
Test results of 10 bus, IEEE 14 and 30 bus systems are shown that
STS can improve the original measured scheme to be observable
without critical measurement pair. Moreover, the results of STS are
superior to deterministic tabu search (DTS) in terms of the best
solution hit.
Abstract: In this study, the effect of greywater irrigation on airwater interfacial area is investigated. Several soil column experiments were conducted for different greywater irrigation to develop the pressure-saturation curves. Surface tension was measured for different greywater concentration and fitted for Gibbs adsorption equation. Pressure-saturation curves show that the reduction of capillary rise stops when it reaches its critical micelle concentration (CMC). A simple theory is derived from pressure-saturation curves for calculating air-water interfacial area in porous medium during greywater irrigation by introducing a term 'hydraulic radius' for the pores. This term diminishes any effect of pore shapes on the air-water interfacial area. The air-water interfacial area was calculated using the pressure-saturation curves and found that it decreases with increasing moisture content. But no significant effect was observed on air-water interfacial area for different greywater irrigation. A maximum of 10% variation in interfacial area was observed at the residual saturation zone.
Abstract: The process of laser absorption in the skin during
laser irradiation was a critical point in medical application
treatments. Delivery the correct amount of laser light is a critical
element in photodynamic therapy (PDT). More amounts of laser
light able to affect tissues in the skin and small amount not able to
enhance PDT procedure in skin. The knowledge of the skin tone
laser dependent distribution of 635 nm radiation and its penetration
depth in skin is a very important precondition for the investigation of
advantage laser induced effect in (PDT) in epidermis diseases
(psoriasis). The aim of this work was to estimate an optimum effect
of diode laser (635 nm) on the treatment of epidermis diseases in
different color skin. Furthermore, it is to improve safety of laser in
PDT in epidermis diseases treatment. Advanced system analytical
program (ASAP) which is a new approach in investigating the PDT,
dependent on optical properties of different skin color was used in
present work. A two layered Realistic Skin Model (RSM); stratum
corneum and epidermal with red laser (635 nm, 10 mW) were used
for irradiative transfer to study fluence and absorbance in different
penetration for various human skin colors. Several skin tones very
fair, fair, light, medium and dark are used to irradiative transfer. This
investigation involved the principles of laser tissue interaction when
the skin optically injected by a red laser diode. The results
demonstrated that the power characteristic of a laser diode (635 nm)
can affect the treatment of epidermal disease in various color skins.
Power absorption of the various human skins were recorded and
analyzed in order to find the influence of the melanin in PDT
treatment in epidermal disease. A two layered RSM show that the
change in penetration depth in epidermal layer of the color skin has a
larger effect on the distribution of absorbed laser in the skin; this is
due to the variation of the melanin concentration for each color.
Abstract: This paper presents the application of an enhanced
Particle Swarm Optimization (EPSO) combined with Gaussian
Mutation (GM) for solving the Dynamic Economic Dispatch (DED)
problem considering the operating constraints of generators. The
EPSO consists of the standard PSO and a modified heuristic search
approaches. Namely, the ability of the traditional PSO is enhanced
by applying the modified heuristic search approach to prevent the
solutions from violating the constraints. In addition, Gaussian
Mutation is aimed at increasing the diversity of global search, whilst
it also prevents being trapped in suboptimal points during search. To
illustrate its efficiency and effectiveness, the developed EPSO-GM
approach is tested on the 3-unit and 10-unit 24-hour systems
considering valve-point effect. From the experimental results, it can
be concluded that the proposed EPSO-GM provides, the accurate
solution, the efficiency, and the feature of robust computation
compared with other algorithms under consideration.
Abstract: Array signal processing involves signal enumeration and source localization. Array signal processing is centered on the ability to fuse temporal and spatial information captured via sampling signals emitted from a number of sources at the sensors of an array in order to carry out a specific estimation task: source characteristics (mainly localization of the sources) and/or array characteristics (mainly array geometry) estimation. Array signal processing is a part of signal processing that uses sensors organized in patterns or arrays, to detect signals and to determine information about them. Beamforming is a general signal processing technique used to control the directionality of the reception or transmission of a signal. Using Beamforming we can direct the majority of signal energy we receive from a group of array. Multiple signal classification (MUSIC) is a highly popular eigenstructure-based estimation method of direction of arrival (DOA) with high resolution. This Paper enumerates the effect of missing sensors in DOA estimation. The accuracy of the MUSIC-based DOA estimation is degraded significantly both by the effects of the missing sensors among the receiving array elements and the unequal channel gain and phase errors of the receiver.
Abstract: In the present study, 49 Hybrid (Catla catla ♂ x
Labeo rohita ♀) were sampled from Al-Raheem Fish Hatchery,
Village Ali Pure Shamali, Jhang Road, 18 Km from Muzaffar Garh
using a cast net and Live fishes were transported to research
laboratory. Mean percentage for water found 79.13 %, ash 6.58 %, fat
2.22 % and protein content 12.06 % in whole wet body weight. It was
observed that body constituents were found increasing in the same
proportion with an increase in body weight while significant
proportional increase was observed with total length. However,
condition factor remained insignificant (P>0.05) with body
constituents.
Abstract: Distance visualization of large datasets often takes the direction of remote viewing and zooming techniques of stored static images. However, the continuous increase in the size of datasets and visualization operation causes insufficient performance with traditional desktop computers. Additionally, the visualization techniques such as Isosurface depend on the available resources of the running machine and the size of datasets. Moreover, the continuous demand for powerful computing powers and continuous increase in the size of datasets results an urgent need for a grid computing infrastructure. However, some issues arise in current grid such as resources availability at the client machines which are not sufficient enough to process large datasets. On top of that, different output devices and different network bandwidth between the visualization pipeline components often result output suitable for one machine and not suitable for another. In this paper we investigate how the grid services could be used to support remote visualization of large datasets and to break the constraint of physical co-location of the resources by applying the grid computing technologies. We show our grid enabled architecture to visualize large medical datasets (circa 5 million polygons) for remote interactive visualization on modest resources clients.