Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: The zero inflated models are usually used in modeling
count data with excess zeros where the existence of the excess zeros
could be structural zeros or zeros which occur by chance. These type
of data are commonly found in various disciplines such as finance,
insurance, biomedical, econometrical, ecology, and health sciences
which involve sex and health dental epidemiology. The most popular
zero inflated models used by many researchers are zero inflated
Poisson and zero inflated negative binomial models. In addition, zero
inflated generalized Poisson and zero inflated double Poisson models
are also discussed and found in some literature. Recently zero
inflated inverse trinomial model and zero inflated strict arcsine
models are advocated and proven to serve as alternative models in
modeling overdispersed count data caused by excessive zeros and
unobserved heterogeneity. The purpose of this paper is to review
some related literature and provide a variety of examples from
different disciplines in the application of zero inflated models.
Different model selection methods used in model comparison are
discussed.
Abstract: The volume of biosolids produced in Malaysia
nowadays had increased proportionally to its population size. The end
products from the waste treatments were mounting, thus inevitable
that in the end the environment will be surrounded by the waste. This
study was conducted to investigate the suitability of biosolids to be
reused as fertilizer for non-food crop. By varying the concentration of
biosolids applied onto the soil, growth of five ornamental plant
samples were tested for eight consecutive weeks. The results show
that the pH of the soil after the addition of biosolids ranges from 6.45
to 6.56 which is suitable for the plant growth. The soil samples that
contains biosolid also show higher amount of macronutrients (N, P,
K) and the heavy metals content are significantly increased in the
plant however it does not exceed the guidelines drawn by the
Environmental Protection Agency. It is also proven that there was
only small significant different in the performance of plant growth
between biosolids and commercial fertilizer. It can be seen that
biosolids was able to perform just as well as commercial fertilizer.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: This study applies the sequential panel selection
method (SPSM) procedure proposed by Chortareas and Kapetanios
(2009) to investigate the time-series properties of energy
consumption in 50 US states from 1963 to 2009. SPSM involves the
classification of the entire panel into a group of stationary series and
a group of non-stationary series to identify how many and which
series in the panel are stationary processes. Empirical results obtained
through SPSM with the panel KSS unit root test developed by Ucar
and Omay (2009) combined with a Fourier function indicate that
energy consumption in all the 50 US states are stationary. The results
of this study have important policy implications for the 50 US states.
Abstract: In vitro plant regeneration has been successfully obtained from basal shoot explant of Vetiveria zizanioides through indirect organogenesis. The explant was cultured in Murashige & Skoog’s (MS) media supplemented with 2,4-D, IAA, and kinetin in various concentrations. Callus was well induced in media supplemented with 2 ppm 2,4-D, 1 ppm IAA, and 1 ppm kinetin. This callus was then transferred to MS media supplemented with 1 - 5 ppm of BAP for shoot regeneration. The media supplemented with 3 ppm BAP was a suitable medium for shoot induction, as well as for shoot multiplication. Rooting was well developed in shoot following transferred to half MS media containing 0.2 ppm IBA. Plantlet was then transferred to husk charcoal for acclimatization, and almost all (90%) of plantlets were survived during acclimatization.
Abstract: Interactive public displays give access as an
innovative media to promote enhanced communication between
people and information. However, digital public displays are subject
to a few constraints, such as content presentation. Content
presentation needs to be developed to be more interesting to attract
people’s attention and motivate people to interact with the display. In
this paper, we proposed idea to implement contents with interaction
elements for vision-based digital public display. Vision-based
techniques are applied as a sensor to detect passers-by and theme
contents are suggested to attract their attention for encouraging them
to interact with the announcement content. Virtual object, gesture
detection and projection installation are applied for attracting
attention from passers-by. Preliminary study showed positive
feedback of interactive content designing towards the public display.
This new trend would be a valuable innovation as delivery of
announcement content and information communication through this
media is proven to be more engaging.
Abstract: This paper presents the exergy analysis of a
desalination unit using humidification-dehumidification process.
Here, this unit is considered as a thermal system with three main
components, which are the heating unit by using a solar collector, the
evaporator or the humidifier, and the condenser or the dehumidifier.
In these components the exergy is a measure of the quality or grade
of energy and it can be destroyed in them. According to the second
law of thermodynamics this destroyed part is due to irreversibilities
which must be determined to obtain the exergetic efficiency of the
system.
In the current paper a computer program has been developed using
visual basic to determine the exergy destruction and the exergetic
efficiencies of the components of the desalination unit at variable
operation conditions such as feed water temperature, outlet air
temperature, air to feed water mass ratio and salinity, in addition to
cooling water mass flow rate and inlet temperature, as well as
quantity of solar irradiance.
The results obtained indicate that the exergy efficiency of the
humidifier increases by increasing the mass ratio and decreasing the
outlet air temperature. In the other hand the exergy efficiency of the
condenser increases with the increase of this ratio and also with the
increase of the outlet air temperature.
Abstract: With the proliferation of mobile computing technology, mobile learning (m-learning) will play a vital role in the rapidly growing electronic learning market. However, the acceptance of m-learning by individuals is critical to the successful implementation of m-learning systems. Thus, there is a need to research the factors that affect users- intention to use m-learning. Based on an updated information system (IS) success model, data collected from 350 respondents in Taiwan were tested against the research model using the structural equation modeling approach. The data collected by questionnaire were analyzed to check the validity of constructs. Then hypotheses describing the relationships between the identified constructs and users- satisfaction were formulated and tested.
Abstract: A study was carried out at the Rice Research Institute of Iran (RRII) to investigate the effect of rollers differential peripheral speed of commercial rubber roll husker and paddy moisture content on the husking index and percentage of broken rice. The experiment was conducted at six levels of rollers differential speed (1.5, 2.2, 2.9, 3.6, 4.3 and 5 m/s) and three levels of paddy moisture content (8-9, 10-11 and 12-13% w.b.). Two common paddy varieties namely, Binam and Khazer, were selected for this study. Results revealed that the effect of rollers differential speed and moisture content significantly (P
Abstract: In this paper, experimental testing and numerical analysis were used to investigate the effect of tube thickness on the face bending for concrete filled hollow sections connected to other structural members using Extended Hollobolts. Six samples were tested experimentally by applying pull-out load on the bolts. These samples were designed to fail by column face bending. The main variable in all tests is the column face thickness. Finite element analyses were also performed using ABAQUS 6.11 to extend the experimental results and to quantify the effect of column face thickness. Results show that, the column face thickness has a clear impact on the connection strength and stiffness. However, the amount of improvement in the connection stiffness by changing the column face thickness from 5mm to 6.3mm seems to be higher than that when increasing it from 6.3mm to 8mm. The displacement at which the bolts start pulling-out from their holes increased with the use of thinner column face due to the high flexibility of the section. At the ultimate strength, the yielding of the column face propagated to the column corner and there was no yielding in its walls. After the ultimate resistance is reached, the propagation of the yielding was mainly in the column face with a miner yielding in the walls.
Abstract: This paper describes a method to improve the robustness of a face recognition system based on the combination of two compensating classifiers. The face images are preprocessed by the appearance-based statistical approaches such as Principal Component Analysis (PCA) and Linear Discriminant Analysis (LDA). LDA features of the face image are taken as the input of the Radial Basis Function Network (RBFN). The proposed approach has been tested on the ORL database. The experimental results show that the LDA+RBFN algorithm has achieved a recognition rate of 93.5%
Abstract: Electrocardiogram (ECG) data compression algorithm
is needed that will reduce the amount of data to be transmitted, stored
and analyzed, but without losing the clinical information content. A
wavelet ECG data codec based on the Set Partitioning In Hierarchical
Trees (SPIHT) compression algorithm is proposed in this paper. The
SPIHT algorithm has achieved notable success in still image coding.
We modified the algorithm for the one-dimensional (1-D) case and
applied it to compression of ECG data.
By this compression method, small percent root mean square
difference (PRD) and high compression ratio with low
implementation complexity are achieved. Experiments on selected
records from the MIT-BIH arrhythmia database revealed that the
proposed codec is significantly more efficient in compression and in
computation than previously proposed ECG compression schemes.
Compression ratios of up to 48:1 for ECG signals lead to acceptable
results for visual inspection.
Abstract: It is a challenge to provide a wide range of queries to
database query systems for small mobile devices, such as the PDAs
and cell phones. Currently, due to the physical and resource
limitations of these devices, most reported database querying systems
developed for them are only offering a small set of pre-determined
queries for users to possibly pose. The above can be resolved by
allowing free-form queries to be entered on the devices. Hence, a
query language that does not restrict the combination of query terms
entered by users is proposed. This paper presents the free-form query
language and the method used in translating free-form queries to
their equivalent SQL statements.
Abstract: Gradual patterns have been studied for many years as
they contain precious information. They have been integrated in
many expert systems and rule-based systems, for instance to reason
on knowledge such as “the greater the number of turns, the greater
the number of car crashes”. In many cases, this knowledge has been
considered as a rule “the greater the number of turns → the greater
the number of car crashes” Historically, works have thus been
focused on the representation of such rules, studying how implication
could be defined, especially fuzzy implication. These rules were
defined by experts who were in charge to describe the systems they
were working on in order to turn them to operate automatically. More
recently, approaches have been proposed in order to mine databases
for automatically discovering such knowledge. Several approaches
have been studied, the main scientific topics being: how to determine
what is an relevant gradual pattern, and how to discover them as
efficiently as possible (in terms of both memory and CPU usage).
However, in some cases, end-users are not interested in raw level
knowledge, and are rather interested in trends. Moreover, it may be
the case that no relevant pattern can be discovered at a low level of
granularity (e.g. city), whereas some can be discovered at a higher
level (e.g. county). In this paper, we thus extend gradual pattern
approaches in order to consider multiple level gradual patterns. For
this purpose, we consider two aggregation policies, namely
horizontal and vertical.
Abstract: In the paper the method of product analysis from
recycling point of view has been described. The analysis bases on set
of measures that assess a product from the point of view of final
stages of its lifecycle. It was assumed that such analysis will be
performed at the design phase – in order to conduct such analysis the
computer system that aids the designer during the design process has
been developed. The structure of the computer tool, based on agent
technology, and example results has been also included in the paper.
Abstract: In the planning point of view, it is essential to have
mode choice, due to the massive amount of incurred in transportation
systems. The intercity travellers in Libya have distinct features, as
against travellers from other countries, which includes cultural and
socioeconomic factors. Consequently, the goal of this study is to
recognize the behavior of intercity travel using disaggregate models,
for projecting the demand of nation-level intercity travel in Libya.
Multinomial Logit Model for all the intercity trips has been
formulated to examine the national-level intercity transportation in
Libya. The Multinomial logit model was calibrated using nationwide
revealed preferences (RP) and stated preferences (SP) survey. The
model was developed for deference purpose of intercity trips (work,
social and recreational). The variables of the model have been
predicted based on maximum likelihood method. The data needed for
model development were obtained from all major intercity corridors
in Libya. The final sample size consisted of 1300 interviews. About
two-thirds of these data were used for model calibration, and the
remaining parts were used for model validation. This study, which is
the first of its kind in Libya, investigates the intercity traveler’s
mode-choice behavior. The intercity travel mode-choice model was
successfully calibrated and validated. The outcomes indicate that, the
overall model is effective and yields higher precision of estimation.
The proposed model is beneficial, due to the fact that, it is receptive
to a lot of variables, and can be employed to determine the impact of
modifications in the numerous characteristics on the need for various
travel modes. Estimations of the model might also be of valuable to
planners, who can estimate possibilities for various modes and
determine the impact of unique policy modifications on the need for
intercity travel.
Abstract: Exploding concentrated underwater charges to
damage underwater structures such as ship hulls is a part of naval
warfare strategies. Adding small amounts of foreign particles (like
clay or silica) of nanosize significantly improves the engineering
properties of the polymers. In the present work the clay in terms 1, 2
and 3 percent by weight was surface treated with a suitable silane
agent. The hybrid nanocomposite was prepared by the hand lay-up
technique. Mathematical regression models have been employed for
theoretical prediction. This will result in considerable savings in terms of project time, effort and cost.
Abstract: Traveling salesman problem (TSP) is hard to resolve
when the number of cities and routes become large. The frequency
graph is constructed to tackle the problem. A frequency graph
maintains the topological relationships of the original weighted graph.
The numbers on the edges are the frequencies of the edges emulated
from the local optimal Hamiltonian paths. The simplest kind of local
optimal Hamiltonian paths are computed based on the four vertices
and three lines inequality. The search algorithm is given to find the
optimal Hamiltonian circuit based on the frequency graph. The
experiments show that the method can find the optimal Hamiltonian
circuit within several trials.
Abstract: Tackling emergency situations is performed based on emergency scenarios. These scenarios do not have a uniform form in the Czech Republic. They are unstructured and developed primarily in the text form. This does not allow solving emergency situations efficiently. For this reason, the paper aims at defining a Process Oriented Architecture to support and thus to improve tackling emergency situations in the Czech Republic. The innovative Process Oriented Architecture is based on the Workflow Reference Model while taking into account the options of Business Process Management Suites for the implementation of process oriented emergency scenarios. To verify the proposed architecture the Proof of Concept has been used which covers the reception of an emergency event at the district emergency operations centre. Within the particular implementation of the proposed architecture the Bonita Open Solution has been used. The architecture created in this way is suitable not only for emergency management, but also for educational purposes.