Abstract: The properties of locally produced metakaolin (MK) as cement replacing material and the comparison of reactivity with commercially available micro-silica have been investigated. Compressive strength, splitting tensile strength, and load-deflection behaviour under bending are the properties that have been studied. The amorphous phase of MK with micro-silica was compared through X-ray diffraction (XRD) pattern. Further, interfacial transition zone of concrete with micro-silica and MK was observed through Field Emission Scanning Electron Microscopy (FESEM). Three mixes of concrete were prepared. One of the mix is without cement replacement as control mix, and the remaining two mixes are 10% cement replacement with micro-silica and MK. It has been found that MK, due to its irregular structure and amorphous phase, has high reactivity with portlandite in concrete. The compressive strength at early age is higher with MK as compared to micro-silica. MK concrete showed higher splitting tensile strength and higher load carrying capacity as compared to control and micro-silica concrete at all ages respectively.
Abstract: The commercial production of biodiesel using microalgae demands a high-energy input for harvesting biomass, making production economically unfeasible. Methods currently used involve mechanical, chemical, and biological procedures. In this work, a flocculation system is presented as a cost and energy effective process to increase biomass production of Phaeodactylum tricornutum. This diatom is the only species of the genus that present fast growth and lipid accumulation ability that are of great interest for biofuel production. The algae, selected from the Bank of Microalgae, Institute of Biology, Federal University of Bahia (Brazil), have been bred in tubular reactor with photoperiod of 12 h (clear/dark), providing luminance of about 35 μmol photons m-2s-1, and temperature of 22 °C. The medium used for growing cells was the Conway medium, with addition of silica. The seaweed growth curve was accompanied by cell count in Neubauer camera and by optical density in spectrophotometer, at 680 nm. The precipitation occurred at the end of the stationary phase of growth, 21 days after inoculation, using two methods: centrifugation at 5000 rpm for 5 min, and electro-flocculation at 19 EPD and 95 W. After precipitation, cells were frozen at -20 °C and, subsequently, lyophilized. Biomass obtained by electro-flocculation was approximately four times greater than the one achieved by centrifugation. The benefits of this method are that no addition of chemical flocculants is necessary and similar cultivation conditions can be used for the biodiesel production and pharmacological purposes. The results may contribute to improve biodiesel production costs using marine microalgae.
Abstract: We have aimed to produce a self-cleaning transparent
polymer coating with polyurethane (PU) matrix as the latter is highly
solvent, chemical and weather resistant having good mechanical
properties. Nano-silica modified by 1H, 1H, 2H, 2Hperflurooctyltriethoxysilane
was incorporated into the PU matrix for
attaining self-cleaning ability through hydrophobicity. The
modification was confirmed by particle size analysis and scanning
electron microscopy (SEM). Thermo-gravimetric (TGA) studies were
carried to ascertain the grafting of silane onto the silica. Several
coating formulations were prepared by varying the silica loading
content and compared to a commercial equivalent. The effect of
dispersion and the morphology of the coated films were assessed by
SEM analysis. All coating standardized tests like solvent resistance,
adhesion, flexibility, acid, alkali, gloss etc. have been performed as
per ASTM standards. Water contact angle studies were conducted to
analyze the hydrophobic character of the coating. In addition, the
coatings were also subjected to salt spray and accelerated weather
testing to analyze the durability of the coating.
Abstract: Electro-osmosis in clayey soils and sediments, for
purposes of clay consolidation, dewatering, or cleanup, and electro
injection in porous media is widespread recent decades. It is
experimentally found that the chemical properties of porous media
especially PH change the characteristics of media. Electro-osmotic
conductivity is a function of soil and grout material chemistry,
altering with time. Many numerical approaches exist to simulate the
of electro kinetic flow rate considering chemical changes. This paper
presents a simplified analytical solution for constant flow rate based
on varying electro osmotic conductivity and time dependent viscosity
for injection of colloidal silica.
Abstract: This paper presents the effects of mixing procedures
on mechanical properties of flyash-based geopolymer matrices
containing nanosilica (NS) at 0.5%, 1.0%, 2.0%, and 3.0% by weight.
Comparison is made with conventional mechanical dry-mixing of NS
with flyash and wet-mixing of NS in alkaline solutions. Physical and
mechanical properties are investigated using X-Ray Diffraction
(XRD) and Scanning Electron Microscope (SEM). Results show that
generally the addition of NS particles enhanced the microstructure
and improved flexural and compressive strengths of geopolymer
nanocomposites. However, samples, prepared using dry-mixing
approach, demonstrate better physical and mechanical properties
comparing to wet-mixing samples.
Abstract: In present study, a large deposit of oolitic iron ore of
Late Carboniferous-Permotriassic-Lower Jurassic age was discovered
in Wadi Halfa and Argein areas, North Sudan. It seems that the iron
ore mineralization exists in the west and east bank of the River Nile
of the study area that are found on the Egyptian-Sudanese border.
The Carboniferous-Lower Jurassic age strata were covered by 67
sections and each section has been examined and carefully described.
The iron-ore in Wadi Halfa occurs as oolitic ironstone and contained
two horizons: (A) horizon and (B) horizon. Only horizon (A) was
observed in southern Argein area. The texture of the ore is variable
depending on the volume of the component. In thin sections, the
average of the ooids was ranged between 90%-80%. The matrix
varies between 10%-20% by volume and detritus quartz in other
component my reach up to 30% by volume in sandy massive ore.
Ooids size ranges from 0.2mm-1.00 mm on average in very coarse
ooids may attend up to 1 mm in size. The matrix around the ooids is
dominated by iron hydroxide, carbonate, fine, and amorphous silica.
The probable ore reserve estimate of 1.234 billion at a head grade of
41.29% Fe for the Wadi Halfa Oolitic Ironstone Formation. The iron
ore shows higher content of phosphorus ranges from 6.15% to 0.16%,
with mean 1.45%. The new technology Hatch–Ironstone Chloride
Segregation (HICS) can be used to produce commercial-quality of
iron and reduce phosphorus and silica to acceptable levels for steel
industry. The presence of infrastructures in addition to the presence
of massive quantities of iron ore would make exploitation
economically.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The commercial white tyres are usually used for forklifts in food and medicine industries. Conventionally, silica is used as reinforcement in the tyres. However, the adhesion between silica particles and rubber is remarkably poor. To improve the problem of adhesion and hence enhance wear resistance, modification of silica surface is one of the solutions. In this work, the natural rubber compound blending with polyisoprene-coated silica prepared by admicellar polymerization technique was studied to compare with the natural rubber compound of unmodified silica. The surface characterization of modified silica was also examined by SEM, FTIR, and TGA. The results show that polyisoprene-coated silica/natural rubber compound gave better overall mechanical properties, especially wear resistance with the improvement of the adhesion between silica and natural rubber matrix that can be seen in the SEM micrograph.
Abstract: In this study two series of self compacting concrete
mixtures were prepared with 100% coarse recycled concrete
aggregates and different percentages of 0%, 20%, 40%, 60%, 80%
and 100% fine recycled concrete aggregates. In series I and II the
water to binder ratios were 0.50 and 0.45, respectively. The cement
content was kept 350
3 m
kg for those mixtures that don't have any
Nano-Silica. To improve the compressive strength of samples, Nano-
Silica replaced with 10% of cement weight in concrete mixtures. By
doing the tests, the results showed that, adding Nano-silica to the
samples with less percentage of fine recycled concrete aggregates,
lead to more increase on the compressive strength.
Abstract: Batch fermentation of 5, 10 and 25 g/L biodiesel
derived crude glycerol was carried out at 30, 37 and 450C by
Clostridium pasteurianum cells immobilized on silica. Maximum
yield of 1,3-propanediol (PDO) (0.60 mol/mol), and ethanol (0.26
mol/mol) were obtained from 10 g/L crude glycerol at 30 and 370C
respectively. Maximum yield of butanol (0.28 mol/mol substrate
added) was obtained at 370C with 25 g/L substrate. None of the three
products were detected at 45oC even after 10 days of fermentation.
Only traces of ethanol (0.01 mol/mol) were detected at 450C with 5
g/L substrate. The results obtained for 25 g/L substrate utilization
were fitted in first order rate equation to obtain the values of rate
constant at three different temperatures for bioconversion of glycerol.
First order rate constants for bioconversion of glycerol at 30, 37 and
45oC were found to be 0.198, 0.294 and 0.029/day respectively.
Activation energy (Ea) for crude glycerol bioconversion was
calculated to be 57.62 kcal/mol.
Abstract: Exploding concentrated underwater charges to
damage underwater structures such as ship hulls is a part of naval
warfare strategies. Adding small amounts of foreign particles (like
clay or silica) of nanosize significantly improves the engineering
properties of the polymers. In the present work the clay in terms 1, 2
and 3 percent by weight was surface treated with a suitable silane
agent. The hybrid nanocomposite was prepared by the hand lay-up
technique. Mathematical regression models have been employed for
theoretical prediction. This will result in considerable savings in terms of project time, effort and cost.