Abstract: This study presents a systematic analysis of wetted region due to cooling of aluminum plate by water spray impingement with respect to different water flow rates, spray nozzle heights, and subcooling. Unlike jet impingement, the wetting is not commenced upon spray impingement and there is a delay in wetness of hot test surface. After initiation, the wetting (black zone) progresses gradually to cover all test plate and provides efficient cooling in nucleate boiling regime. Generally, spray cooling is found function of spray flow rate, spray-to-surface distance and water subcooling. Wetting delay is decreasing by increasing of spray flow rate until spray impact area is not become bigger that test surface. Otherwise, higher spray flow rate is not practically accelerated start of wetting. Very fast wetting due to spray cooling can be obtained by dense spray (high floe rate) discharged from adjacent nozzle to the test surface. Highly subcooling water spray also triggers earlier wetting of hot aluminum plate.
Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Fossil fuels are the major source to meet the world
energy requirements but its rapidly diminishing rate and adverse
effects on our ecological system are of major concern. Renewable
energy utilization is the need of time to meet the future challenges.
Ocean energy is the one of these promising energy resources. Threefourths
of the earth-s surface is covered by the oceans. This enormous
energy resource is contained in the oceans- waters, the air above the
oceans, and the land beneath them. The renewable energy source of
ocean mainly is contained in waves, ocean current and offshore solar
energy. Very fewer efforts have been made to harness this reliable
and predictable resource. Harnessing of ocean energy needs detail
knowledge of underlying mathematical governing equation and their
analysis. With the advent of extra ordinary computational resources
it is now possible to predict the wave climatology in lab simulation.
Several techniques have been developed mostly stem from numerical
analysis of Navier Stokes equations. This paper presents a brief over
view of such mathematical model and tools to understand and
analyze the wave climatology. Models of 1st, 2nd and 3rd generations
have been developed to estimate the wave characteristics to assess the
power potential. A brief overview of available wave energy
technologies is also given. A novel concept of on-shore wave energy
extraction method is also presented at the end. The concept is based
upon total energy conservation, where energy of wave is transferred
to the flexible converter to increase its kinetic energy. Squeezing
action by the external pressure on the converter body results in
increase velocities at discharge section. High velocity head then can
be used for energy storage or for direct utility of power generation.
This converter utilizes the both potential and kinetic energy of the
waves and designed for on-shore or near-shore application. Increased
wave height at the shore due to shoaling effects increases the
potential energy of the waves which is converted to renewable
energy. This approach will result in economic wave energy
converter due to near shore installation and more dense waves due to
shoaling. Method will be more efficient because of tapping both
potential and kinetic energy of the waves.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: A local municipality has decided to build a sewage pit
to receive residential sewage waste arriving by tank trucks. Daily
accumulated waste are to be pumped to a nearby waste water
treatment facility to be re-consumed for agricultural and construction
projects. A discrete-event simulation model using Arena Software
was constructed to assist in defining the capacity of the system in
cubic meters, number of tank trucks to use the system, number of
unload docks required, number of standby areas needed and
manpower required for data collection at entrance checkpoint and
truck tank load toxicity testing. The results of the model are
statistically validated. Simulation turned out to be an excellent tool
in the facility planning effort for the pit project, as it insured smooth
flow lines of tank trucks load discharge and best utilization of
facilities on site.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: The main criteria of designing in the most hydraulic
constructions essentially are based on runoff or discharge of water. Two of those important criteria are runoff and return period. Mostly,
these measures are calculated or estimated by stochastic data.
Another feature in hydrological data is their impreciseness.
Therefore, in order to deal with uncertainty and impreciseness, based
on Buckley-s estimation method, a new fuzzy method of evaluating hydrological measures are developed. The method introduces
triangular shape fuzzy numbers for different measures in which both
of the uncertainty and impreciseness concepts are considered. Besides, since another important consideration in most of the
hydrological studies is comparison of a measure during different
months or years, a new fuzzy method which is consistent with special form of proposed fuzzy numbers, is also developed. Finally, to
illustrate the methods more explicitly, the two algorithms are tested on one simple example and a real case study.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: In electronegative-electropositive gas mixtures plasma, at a total pressure varying in the range of ten to hundred Torr, the appearance of a quasi-mochromatization effect of the emitted radiation was reported. This radiation could be the result of the generating mechanisms at molecular level, which is the case of the excimer radiation but also at atomic level. Thus, in the last case, in (Ne+1%Ar/Xe+H2) gas mixtures plasma in a dielectric barrier discharge, this effect, called M-effect, consists in the reduction of the discharge emission spectrum practice at one single, strong spectral line with λ = 585.3 nm. The present paper is concerned with the characteristics comparative investigation of the principal reaction mechanisms involved in the quasi-monochromatization effect existence in the case of the excimer radiation, respectively of the Meffect. Also, the paper points out the role of the metastable electronegative atoms in the appearance of the monochromatization – effect at atomic level.
Abstract: Prediction of highly non linear behavior of suspended
sediment flow in rivers has prime importance in the field of water
resources engineering. In this study the predictive performance of
two Artificial Neural Networks (ANNs) namely, the Radial Basis
Function (RBF) Network and the Multi Layer Feed Forward (MLFF)
Network have been compared. Time series data of daily suspended
sediment discharge and water discharge at Pari River was used for
training and testing the networks. A number of statistical parameters
i.e. root mean square error (RMSE), mean absolute error (MAE),
coefficient of efficiency (CE) and coefficient of determination (R2)
were used for performance evaluation of the models. Both the models
produced satisfactory results and showed a good agreement between
the predicted and observed data. The RBF network model provided
slightly better results than the MLFF network model in predicting
suspended sediment discharge.
Abstract: Insulation used in transformer is mostly oil pressboard insulation. Insulation failure is one of the major causes of catastrophic failure of transformers. It is established that partial discharges (PD) cause insulation degradation and premature failure of insulation. Online monitoring of PDs can reduce the risk of catastrophic failure of transformers. There are different techniques of partial discharge measurement like, electrical, optical, acoustic, opto-acoustic and ultra high frequency (UHF). Being non invasive and non interference prone, acoustic emission technique is advantageous for online PD measurement. Acoustic detection of p.d. is based on the retrieval and analysis of mechanical or pressure signals produced by partial discharges. Partial discharges are classified according to the origin of discharges. Their effects on insulation deterioration are different for different types. This paper reports experimental results and analysis for classification of partial discharges using acoustic emission signal of laboratory simulated partial discharges in oil pressboard insulation system using three different electrode systems. Acoustic emission signal produced by PD are detected by sensors mounted on the experimental tank surface, stored on an oscilloscope and fed to computer for further analysis. The measured AE signals are analyzed using discrete wavelet transform analysis and wavelet packet analysis. Energy distribution in different frequency bands of discrete wavelet decomposed signal and wavelet packet decomposed signal is calculated. These analyses show a distinct feature useful for PD classification. Wavelet packet analysis can sort out any misclassification arising out of DWT in most cases.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: The current sheath dynamics in plasma focus facilities
is the most important factors. In this paper the current sheath velocity
at three dimensional with Sahand plasma focus facility is
investigated. For this purpose the discharge is produced in argon gas
with deposited energy lying in the range of 20-37kJ. The current
sheath is monitored using two tridimensional magnetic probes. These
probes installed near the surface of the interior electrode (anode) at
125mm from the anode axis (pinch place). The effect of gas pressure
on the current sheath velocity also is investigated.
Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: This paper presents a silicon controller rectifier (SCR)
based ESD protection circuit for IC. The proposed ESD protection
circuit has low trigger voltage and high holding voltage compared with
conventional SCR ESD protection circuit. Electrical characteristics of
the proposed ESD protection circuit are simulated and analyzed using
TCAD simulator. The proposed ESD protection circuit verified
effective low voltage ESD characteristics with low trigger voltage and
high holding voltage.
Abstract: A first intermediate roll of Sendzirmir mills was failure
by surface spalling during operation. After analyzing by visual, stereo
microscope, optical microscope, scanning electron microscope,
glow-discharged spectrometer and hardness test, respectively, the
results show that some voids and cracks existed on the contact surface
as well as subsurface. Further examination verified inadequate
hardness and inclusions were responsible for the failure of surface
spalling.