Abstract: This study aims to initiate sustainable water management for tourist accommodations in Amphawa, Samut Songkram Province, Thailand. Wastewater generated by tourist accommodation was conducted in 10 homestays and resorts in Amphawa during August – October, 2011. The prominent parameters which are of pH, Dissolved Oxygen (DO), Biochemical Oxygen Demand (BOD), Fat Oil and Grease (FOG), Nitrate (No3-), and Phosphate (PO43-) were conducted monthly. The results revealed that some parameters were over national water quality standard (Class II). Especially, 90% of tourist accommodations have been recorded that FOG was over the standard of wastewater quality from accommodation (group I: total room of accommodation less than 200 rooms). Therefore, grease trap and natural treatment should be utilized in tourist accommodations in order to reduce the discharged of fat, oil, and grease from tourism activities. In addition, number of tourists also relate statistically with BOD and Nitrate at 0.05 level of significance.
Abstract: In aircraft applications, according to the nature of
electrical equipment its location may be in unpressurized area or very
close to the engine; thus, the environmental conditions may change
from atmospheric pressure to less than 100 mbar, and the temperature
may be higher than the ambient one as in most real working
conditions of electrical equipment. Then, the classical Paschen curve
has to be replotted since these parameters may affect the discharge
ignition voltage. In this paper, we firstly investigate the domain of
validity of two corrective expressions on the Paschen-s law found in
the literature, in case of changing the air environment and known as
Peek and Dunbar corrections. Results show that these corrections are
no longer valid for combined variation of temperature and pressure.
After that, a new empirical expression for breakdown voltage is
proposed and is validated in the case of combined variations of
temperature and pressure.
Abstract: Riprap is mostly used to prevent erosion by flows
down the steep slopes in river engineering. A total of 53 stability tests
performed on angular riprap with a median stone size ranging from
15 to 278 mm and slope ranging from 1 to 40% are used in this study.
The existing equations for the prediction of medium size of angular
stones are checked for their accuracy using the available data.
Predictions of median size using these equations are not satisfactory
and results show deviation by more than ±20% from the observed
values. A multivariable power regression analysis is performed to
propose a new equation relating the median size with unit discharge,
bed slope, riprap thickness and coefficient of uniformity. The
proposed relationship satisfactorily predicts the median angular stone
size with ±20% error. Further, the required size of the rounded stone
is more than the angular stone for the same unit discharge and the
ratio increases with unit discharge and also with embankment slope
of the riprap.
Abstract: Channel junctions can be analyzed in two ways of
division (lateral intake) and combined flows (confluence). The
present paper investigates 3D flow pattern at lateral intake using
Navier-Stokes equation and κ -ε (RNG) turbulent model. The
equations are solved by Finite-Volume Method (FVM) and results
are compared with the experimental data of (Barkdoll, B.D., 1997)
to test the validity of the findings. Comparison of the results with
the experimental data indicated a close proximity between the two
sets of data which suggest a very close simulation. Results further
indicated an inverse relation between the effects of discharge ratio
( r Q ) on the length and width of the separation zone. In other words,
as the discharge ration increases, the length and width of separation
zone decreases.
Abstract: This paper presents the experimental results on
ageing deterioration of silicone rubber outdoor polymer insulator
under salt water dip wheel test based on IEC 62217. In order to comparison effect of chemical contents, silicone rubber outdoor
polymer insulators having same configuration and leakage distant
from two manufactures were tested together continuously 30,000 test cycles. Many discharge activities were observed in during the test.
After 30,000 test cycles, in spite of same configuration, differences in
degree of surface aging were observed. Physical analysis such as
decreasing in hydrophobicity and increasing in hardness
measurement were measured on two-type tested specimen surface in order to confirm degree of surface ageing. Furthermore, chemical
analysis by ATR-FTIR to diagnose the chemical change of tested
specimen surface was conducted to confirm the physical analysis results.
Abstract: The interaction of tunneling or mining with
groundwater has become a very relevant problem not only due to the
need to guarantee the safety of workers and to assure the efficiency of
the tunnel drainage systems, but also to safeguard water resources
from impoverishment and pollution risk. Therefore it is very
important to forecast the drainage processes (i.e., the evaluation of
drained discharge and drawdown caused by the excavation). The aim
of this study was to know better the system and to quantify the flow
drained from the Fontane mines, located in Val Germanasca (Turin,
Italy). This allowed to understand the hydrogeological local changes
in time. The work has therefore been structured as follows: the
reconstruction of the conceptual model with the geological,
hydrogeological and geological-structural study; the calculation of
the tunnel inflows (through the use of structural methods) and the
comparison with the measured flow rates; the water balance at the
basin scale. In this way it was possible to understand what are the
relationships between rainfall, groundwater level variations and the
effect of the presence of tunnels as a means of draining water.
Subsequently, it the effects produced by the excavation of the mining
tunnels was quantified, through numerical modeling. In particular,
the modeling made it possible to observe the drawdown variation as a
function of number, excavation depth and different mines linings.
Abstract: Since the beginning of human history, human
activities have caused many changes in the environment. Today, a
particular attention should be paid to gaining knowledge about water
quality of wetlands which are pristine natural environments rich in
genetic reserves. If qualitative conditions of industrial areas (in terms
of both physicochemical and biological conditions) are not addressed
properly, they could cause disruption in natural ecosystems,
especially in rivers. With regards to the quality of water resources,
determination of pollutant sources plays a pivotal role in engineering
projects as well as designing water quality control systems. Thus,
using different methods such as flow duration curves, dischargepollution
load model and frequency analysis by HYFA software
package, risk of various industrial pollutants in international and
ecologically important Gavkhoni wetland is analyzed. In this study, a
station located at Varzaneh City is used as the last station on
Zayanderud River, from where the river water is discharged into the
wetland. Results showed that elements- concentrations often
exceeded the allowed level and river water can endanger regional
ecosystem. In addition, if the river discharge is managed on Q25
basis, this basis can lower concentrations of elements, keeping them
within the normal level.
Abstract: This study investigated the effect of cross sectional
geometry on sediment transport rate. The processes of sediment
transport are generally associated to environmental management,
such as pollution caused by the forming of suspended sediment in the
channel network of a watershed and preserving physical habitats and
native vegetations, and engineering applications, such as the
influence of sediment transport on hydraulic structures and flood
control design. Many equations have been proposed for computing
the sediment transport, the influence of many variables on sediment
transport has been understood; however, the effect of other variables
still requires further research. For open channel flow, sediment
transport capacity is recognized to be a function of friction slope,
flow velocity, grain size, grain roughness and form roughness, the
hydraulic radius of the bed section and the type and quantity of
vegetation cover. The effect of cross sectional geometry of the
channel on sediment transport is one of the variables that need
additional investigation. The width-depth ratio (W/d) is a
comparative indicator of the channel shape. The width is the total
distance across the channel and the depth is the mean depth of the
channel. The mean depth is best calculated as total cross-sectional
area divided by the top width. Channels with high W/d ratios tend to
be shallow and wide, while channels with low (W/d) ratios tend to be
narrow and deep. In this study, the effects of the width-depth ratio on
sediment transport was demonstrated theoretically by inserting the
shape factor in sediment continuity equation and analytically by
utilizing the field data sets for Yalobusha River. It was found by
utilizing the two approaches as a width-depth ratio increases the
sediment transport decreases.
Abstract: This paper presents development of an ignition system using spark electrodes for application in a research explosion vessel.
A single spark is aimed to be discharged with quantifiable ignition energy. The spark electrode system would enable study of flame
propagation, ignitability of fuel-air mixtures and other fundamental characteristics of flames. The principle of the capacitive spark circuit
of ASTM is studied to charge an appropriate capacitance connected across the spark gap through a large resistor by a high voltage from
the source of power supply until the initiation of spark. Different spark energies could be obtained mainly by varying the value of the
capacitance and the supply current. The spark sizes produced are found to be affected by the spark gap, electrode size, input voltage
and capacitance value.
Abstract: Hydrogen is considered to be the most promising
candidate as a future energy carrier. One of the most used
technologies for the electrolytic hydrogen production is alkaline
water electrolysis. However, due to the high energy requirements, the
cost of hydrogen produced in such a way is high. In continuous
search to improve this process using advanced electrocatalytic
materials for the hydrogen evolution reaction (HER), Ni type Raney
and macro-porous Ni-Co electrodes were prepared on AISI 304
stainless steel substrates by electrodeposition. The developed
electrodes were characterized by SEM and confocal laser scanning
microscopy. HER on these electrodes was evaluated in 30 wt.% KOH
solution by means of hydrogen discharge curves and galvanostatic
tests. Results show that the developed electrodes present a most
efficient behaviour for HER when comparing with the smooth Ni
cathode. It has been reported a reduction in the energy consumption
of the electrolysis cell of about 25% by using the developed coatings
as cathodes.
Abstract: Energy generated by the force of water in hydropower
can provide a more sustainable, non-polluting alternative to fossil
fuels, along with other renewable sources of energy, such as wind,
solar and tidal power, bio energy and geothermal energy. Small scale
hydroelectricity in Iran is well suited for “off-grid" rural electricity
applications, while other renewable energy sources, such as wind,
solar and biomass, can be beneficially used as fuel for pumping
groundwater for drinking and small scale irrigation in remote rural
areas or small villages. Small Hydro Power plants in Iran have very
low operating and maintenance costs because they consume no fossil
or nuclear fuel and do not involve high temperature processes. The
equipment is relatively simple to operate and maintain. Hydropower
equipment can adjust rapidly to load changes. The extended
equipment life provides significant economic advantages. Some
hydroelectric plants installed 100 years ago still operate reliably. The
Polkolo river is located on Karun basin at southwest of Iran. Situation
and conditions of Polkolo river are evaluated for construction of
small hydropower in this article. The topographical conditions and
the existence of permanent water from springs provide the suitability
to install hydroelectric power plants on the river Polkolo. The
cascade plant consists of 9 power plants connected with each other
and is having the total head as 1100m and discharge about 2.5cubic
meter per second. The annual production of energy is 105.5 million
kwh.
Abstract: Laboratory experiments have been performed to investigate photocatalytic detoxification by using TiO2 photocatalyst for treating dairy effluent. Various operational parameters such as catalyst concentration, initial concentration, angle of tilt of solar flat plate reactor and flow rate were investigated. Results indicated that the photocatalytic detoxification process can efficiently treat dairy effluent. Experimental runs with dairy wastewater can be used to identify the optimum operational parameters to perform wastewater degradation on large scale for recycling purpose. Also effect of two different types of reactors on degradation process was analyzed.
Abstract: Laser engraving is a manufacturing method for those applications where previously Electrical Discharge Machining (EDM) was the only choice. Laser engraving technology removes material layer-by-layer and the thickness of layers is usually in the range of few microns. The aim of the present work is to investigate the influence of the process parameters on the surface quality when machined by laser engraving. The examined parameters were: the pulse frequency, the beam speed and the layer thickness. The surface quality was determined by the surface roughness for every set of parameters. Experimental results on Al7075 material showed that the surface roughness strictly depends on the process parameters used.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: The investigation results of high-density hydrogen
heating by high-current electric arc are presented at initial pressure
from 5 MPa to 160 MPa with current amplitude up to 1.6 MA and
current rate of rise 109-1011 A/s. When changing the initial pressure
and current rate of rise, channel temperature varies from several
electronvolts to hundreds electronvolts. Arc channel radius is several
millimeters. But the radius of the discharge chamber greater than the
radius of the arc channel on approximately order of magnitude. High
efficiency of gas heating is caused by radiation absorption of
hydrogen surrounding the arc. Current channel consist from vapor of
the initiating wire. At current rate of rise of 109 A/s and relatively
small current amplitude gas heating occurs due to radiation
absorption in the band transparency of hydrogen by the wire vapours
with photon energies less than 13.6 eV. At current rate of rise of
1011 A/s gas heating is due to hydrogen absorption of soft X-rays
from discharge channel.
Abstract: Amphawa is the most popular weekend destination for
both domestic and international tourists in Thailand. More than 112
homestays and resorts have been developed along the water
resources. This research aims to initiate appropriate environmental
management system for riverside tourist accommodations in
Amphawa by investigating current environmental characteristics.
Eighty-eight riverside tourist accommodations were survey from
specific questionnaire, GPS data were also gathered for spatial
analysis. The results revealed that the accommodations are welled
manage in regards to some environmental aspects. In order to reduce
economic costs, energy efficiency equipment is utilized. A substantial
number of tourist accommodations encouraged waste separation,
followed by transfer to local administration organization. Grease
traps also utilized in order to decrease chemical discharged, grease
and oil from canteen and restaurants on natural environment. The
most notable mitigation is to initiate environmental friendly cleansers
for tourist accommodation along the riverside in tourism destinations.
Abstract: Pyrite (FeS2) is a promising candidate for cathode
materials in batteries because of it`s high theoretical capacity, low
cost and non-toxicity. In this study, nano size iron disulfide thin film
was prepared on graphite substrate through a new method as battery
cathode. In this way, acetylene black and poly vinylidene fluoride
were used as electron conductor and binder, respectively. Fabricated
thin films were analyzed by XRD and SEM. These results and
electrochemical data confirm improvement of battery discharge
capacity in comparison with commercial type of pyrite.
Abstract: Smoke discharging is a main reason of air pollution
problem from industrial plants. The obstacle of a building has an
affect with the air pollutant discharge. In this research, a mathematical
model of the smoke dispersion from two sources and one source with
a structural obstacle is considered. The governing equation of the
model is an isothermal mass transfer model in a viscous fluid. The
finite element method is used to approximate the solutions of the
model. The triangular linear elements have been used for discretising
the domain, and time integration has been carried out by semi-implicit
finite difference method. The simulations of smoke dispersion in
cases of one chimney and two chimneys are presented. The maximum
calculated smoke concentration of both cases are compared. It is then
used to make the decision for smoke discharging and air pollutant
control problems on industrial area.
Abstract: Run-offs are considered as important hydrological factors in feasibility studies of river engineering and irrigation-related projects under arid and semi-arid condition. Flood control is one of the crucial factor, the management of which while mitigates its destructive consequences, abstracts considerable volume of renewable water resources. The methodology applied here was based on Mizumura, which applied a mathematical model for simple tank to simulate the rainfall-run-off process in a particular water basin using the data from the observational hydrograph. The model was applied in the Dez River water basin adjacent to Greater Dezful region, Iran in order to simulate and estimate the floods. Results indicated that the calculated hydrographs using the simple tank method, SCS-CN model and the observation hydrographs had a close proximity. It was also found that on average the flood time and discharge peaks in the simple tank were closer to the observational data than the CN method. On the other hand, the calculated flood volume in the CN model was significantly closer to the observational data than the simple tank model.
Abstract: This paper investigates the influence of various
parameters on the behaviour of water droplets on polymeric surfaces
under high electric fields. An inclined plane test was carried out to
understand the droplet behaviour in strong electric field. Parameters
such as water droplet conductivity, droplet volume, polymeric
surface roughness and droplet positioning with respect to the
electrodes were studied. The flashover voltage is affected by all
aforementioned parameters. The droplet positioning is in some cases
more vital than the droplet volume. Surface damages were analysed
using Scanning Electron Microscopy (SEM) studies and by Energy
dispersive X-ray Analysis (EDAX). It is observes that magnitude of
discharge have direct influence on amount of surface da