Abstract: In this experimental work, we have shown that the
geometric shape of the grooves (furrows) plays an important role in
sediment dynamics. In addition, the rheological behaviour of solid
discharge does not depend only on the velocity discharge but also on
the geometric shape.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: Surface water pollution is one of the serious
environmental problems in rural areas of South Africa due to
discharge of household waste into the streams, turning them into
open sewers. In this study, samples of water were collected from a
stream in Soshanguve and analysed. The result showed that pollution
in the area was caused by man and its activities. The water quality in
the area was found to have deterioted significantly after water runoff
from farms and household wastes. The result shows, fertilizer runoff
contributes 50% of the pollution while pesticides and sediments
contribute up to 10% respectively in the streams, while household
waste contributes up to 30%. This study gives an outline of the
sources of water pollution in the area and provides a process of
creating a clean and unpolluted environment for Soshanguve
community in Pretoria north in order to achieve the 7th aim of the
millennium development goals by 2015, which is ensuring
environmental sustainability.
Abstract: In the present work, a study has been made on the combination of the electrical discharge machining (EDM) with ultrasonic vibrations to improve the machining efficiency. In experiments the graphite used as tool electrode and material of workpiece was AISIH13 tool steel. The parameters such as discharge peak current and pulse duration were changed to explore their effect on the material removal rate (MRR), relative tool wear ratio (TWR) and surface roughness. From the experimental result it can be seen that ultrasonic vibration of the workpiece can significantly reduces the inactive pulses and improves the stability of process. It was found that ultrasonic assisted EDM (US-EDM) is effective in attaining a high material removal rate (MRR) in finishing regime.
Abstract: Estimation of stormwater pollutants is a pre-requisite
for the protection and improvement of the aquatic environment and
for appropriate management options. The usual practice for the
stormwater quality prediction is performed through water quality
modeling. However, the accuracy of the prediction by the models
depends on the proper estimation of model parameters. This paper
presents the estimation of model parameters for a catchment water
quality model developed for the continuous simulation of stormwater
pollutants from a catchment to the catchment outlet. The model is
capable of simulating the accumulation and transportation of the
stormwater pollutants; suspended solids (SS), total nitrogen (TN) and
total phosphorus (TP) from a particular catchment. Rainfall and water
quality data were collected for the Hotham Creek Catchment (HTCC),
Gold Coast, Australia. Runoff calculations from the developed model
were compared with the calculated discharges from the widely used
hydrological models, WBNM and DRAINS. Based on the measured
water quality data, model water quality parameters were calibrated
for the above-mentioned catchment. The calibrated parameters are
expected to be helpful for the best management practices (BMPs)
of the region. Sensitivity analyses of the estimated parameters were
performed to assess the impacts of the model parameters on overall
model estimations of runoff water quality.
Abstract: Clean air in subway station is important to passengers. The Platform Screen Doors (PSDs) can improve indoor air quality in the subway station; however the air quality in the subway tunnel is degraded. The subway tunnel has high CO2 concentration and indoor particulate matter (PM) value. The Indoor Air Quality (IAQ) level in subway environment degrades by increasing the frequency of the train operation and the number of the train. The ventilation systems of the subway tunnel need improvements to have better air-quality. Numerical analyses might be effective tools to analyze the performance of subway twin-track tunnel ventilation systems. An existing subway twin-track tunnel in the metropolitan Seoul subway system is chosen for the numerical simulations. The ANSYS CFX software is used for unsteady computations of the airflow inside the twin-track tunnel when the train moves. The airflow inside the tunnel is simulated when one train runs and two trains run at the same time in the tunnel. The piston-effect inside the tunnel is analyzed when all shafts function as the natural ventilation shaft. The supplied air through the shafts is mixed with the pollutant air in the tunnel. The pollutant air is exhausted by the mechanical ventilation shafts. The supplied and discharged airs are balanced when only one train runs in the twin-track tunnel. The pollutant air in the tunnel is high when two trains run simultaneously in opposite direction and all shafts functioned as the natural shaft cases when there are no electrical power supplies in the shafts. The remained pollutant air inside the tunnel enters into the station platform when the doors are opened.
Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: The study of interaction among the grain, moisture,
and the surrounding space (air) is key to understanding the graindrying
process. In Iran, rice (mostly Indica type) is dried by flat
bed type dryer until the final MC reaches to 6 to 8%. The
experiments were conducted to examine the effect of application of
discharge fan with different heights of paddy on the drying
efficiency. Experiments were designed based on two different
configurations of the drying methods; with and without discharge
fan with three different heights of paddy including; 5, 10, and 15
cm. The humid heated air will be going out immediately by the
suction of discharge fan. The drying time is established upon the
average final MC to achieve about 8%. To save energy and reduce
the drying time, the distribution of temperature between layers
should be fast and uniform with minimum difference; otherwise
the difference of MC gradient between layers will be high and will
induce grain breakage. The difference of final MC between layers
in the two methods was 48-73%. The steady state of temperature
between the two methods has saved time in the range of 10-20%,
and the efficiency of temperature distribution increased 17-26% by
the use of discharge fan.
Abstract: The direct discharge of palm oil mill effluent (POME) wastewater causes serious environmental pollution due to its high chemical oxygen demand (COD) and biochemical oxygen demand (BOD). Traditional ways for POME treatment have both economical and environmental disadvantages. In this study, a membrane anaerobic system (MAS) was used as an alternative, cost effective method for treating POME. Six steady states were attained as a part of a kinetic study that considered concentration ranges of 8,220 to 15,400 mg/l for mixed liquor suspended solids (MLSS) and 6,329 to 13,244 mg/l for mixed liquor volatile suspended solids (MLVSS). Kinetic equations from Monod, Contois and Chen & Hashimoto were employed to describe the kinetics of POME treatment at organic loading rates ranging from 2 to 13 kg COD/m3/d. throughout the experiment, the removal efficiency of COD was from 94.8 to 96.5% with hydraulic retention time, HRT from 400.6 to 5.7 days. The growth yield coefficient, Y was found to be 0.62gVSS/g COD the specific microorganism decay rate was 0.21 d-1 and the methane gas yield production rate was between 0.25 l/g COD/d and 0.58 l/g COD/d. Steady state influent COD concentrations increased from 18,302 mg/l in the first steady state to 43,500 mg/l in the sixth steady state. The minimum solids retention time, which was obtained from the three kinetic models ranged from 5 to 12.3 days. The k values were in the range of 0.35 – 0.519 g COD/ g VSS • d and values were between 0.26 and 0.379 d-1. The solids retention time (SRT) decreased from 800 days to 11.6 days. The complete treatment reduced the COD content to 2279 mg/l equivalent to a reduction of 94.8% reduction from the original.
Abstract: Behavior of turbulent jet is relying on jet parameters,
environmental and geometric parameters. In this research, it has
attempt to Study effect of jet parameters of internal angle on
maximum effective length and velocity on centerline from nozzle
experimentally. Toward this end, four internal angles 30, 45, 60 and
90-degree are considered for this study in a flume with 600cm as
long, 100cm as high and 150cm in width. Various discharges were
used to evaluate effective length for a wide range of densimetric
Froude numbers F0, from 17.9 to 39.4 that is defined at the nozzle. As
a result, It is revealed that both velocity on centerline and effective
length decreases when nozzle angle decreased from 90° to 30°. The
results show that, for all range of Fr0 the Um/U0 ratio for nozzle with
α=90° on centerline increases 20% - 27% than nozzle with α=30° that
has lowest velocity on centerline than other nozzle.
Abstract: One of the main and responsible units of Sulzer
projectile loom is picking mechanism. It is specifically designed to
accelerate projectile to speed of 25 m / s. Initial speed projectile of
Sulzer projectile loom is independent of speed loom and determined
the potential energy torsion rod. This paper investigates the dynamics
picking mechanism of Sulzer projectile loom during its discharge. A
result of calculation model, we obtain the law of motion lever of
picking mechanism during its discharge. Construction of dynamic
model the picking mechanism of Sulzer projectile loom on software
complex SimulationX can make calculations for different thickness
of torsion rods taking into account the backlashes in the connections,
the dissipative forces and resistance forces
Abstract: A gold coated copper rotating electrode was used to
eliminate surface oxidation effect. This study examined the effect of
electrode rotation on the ozone generation process and showed that an
ozonizer with an electrode rotating system might be a possible way to
increase ozone-synthesis efficiency. Two new phenomena appeared
during experiments with the rotating electrode. First was that ozone
concentration increased to about two times higher than that of the case
with no rotation. Second, input power and discharge area were found
to increase with the rotation speed. Both ozone concentration and
ozone production efficiency improved in the case of rotating electrode
compared to the case with a non-rotating electrode. One possible
reason for this was the increase in discharge length of
micro-discharges during electrode rotation. The rotating electrode
decreased onset voltage, while reactor capacitance increased with
rotation. Use of a rotating-type electrode allowed earlier observation
of the ozone zero phenomena compared with a non-rotating electrode
because, during rotation, the entire electrode surface was functional,
allowing nitrogen on the electrode surface to be evenly consumed.
Nitrogen demand increased with increasing rotation s
Abstract: Partial discharge (PD) detection is an important
method to evaluate the insulation condition of metal-clad apparatus.
Non-intrusive sensors which are easy to install and have no
interruptions on operation are preferred in onsite PD detection.
However, it often lacks of accuracy due to the interferences in PD
signals. In this paper a novel PD extraction method that uses frequency
analysis and entropy based time-frequency (TF) analysis is introduced.
The repetitive pulses from convertor are first removed via frequency
analysis. Then, the relative entropy and relative peak-frequency of
each pulse (i.e. time-indexed vector TF spectrum) are calculated and
all pulses with similar parameters are grouped. According to the
characteristics of non-intrusive sensor and the frequency distribution
of PDs, the pulses of PD and interferences are separated. Finally the
PD signal and interferences are recovered via inverse TF transform.
The de-noised result of noisy PD data demonstrates that the
combination of frequency and time-frequency techniques can
discriminate PDs from interferences with various frequency
distributions.
Abstract: In the management of industrial waste, conversion from the use of paper invoices to electronic forms is currently under way in developed countries. Difficulties in such computerization include the lack of synchronization between the actual goods and the corresponding data managed by the server. Consequently, a system which utilizes the incorporation of a QR code in connection with the waste material has been developed. The code is read at each stage, from discharge until disposal, and progress at each stage can be easily reported. This system can be linked with Japanese public digital authentication service of waste, taking advantage of its good points, and can be used to submit reports to the regulatory authorities. Its usefulness was confirmed by a verification test, and put into actual practice.
Abstract: The usual method of river flow diversion involves construction of tunnels and cofferdams. Given the fact that the cost of diversion works could be as high as 10-20% of the total dam construction cost, due attention should be paid to optimum design of the diversion works. The cost of diversion works depends, on factors, such as: the tunnel dimensions and the intended tunneling support measures during and after excavation; quality and characterizes of the rock through which the tunnel should be excavated; the dimensions of the upstream (and downstream) cofferdams; and the magnitude of river flood the system is designed to divert. In this paper by use of the cost of unit prices for tunnel excavation, tunnel lining, tunnel support (rock bolt + shotcrete) and cofferdam fill the cost function was determined. The function is then minimized by the aid of PSO Algorithm (particle swarm optimization). It is found that the optimum diameter and the total diversion cost are directly related to the river flood discharge (Q). It has also shown that in addition to optimum diameter design discharge (Q), river length, tunnel length, is mainly a function of the ratios (not the absolute values) of the unit prices and does not depend on the overall price levels in the respective country. The results of optimization use in some of the case study lead us to significant changes in the cost.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: The power transformer is the most expensive, indispensable and arguably the most important equipment item in a power system Insulation failure in transformers can cause long term interruption to supply and loss of revenue and the condition assessment of the insulation is thus an important maintenance procedure. Oil-impregnated transformer insulation consists of mainly organic materials including mineral oil and cellulose-base paper and pressboard. The operating life of cellulose-based insulation, as with most organic insulation, depends heavily on its operating temperature rise above ambient. This paper reports results of a laboratory-based experimental investigation of partial discharge (PD) activity at high temperature in oil-impregnated insulation. The experiments reported here are part an on-going programme aimed at investigating the way in which insulation deterioration can be monitored and quantified by use of partial discharge diagnostics. Partial discharge patterns were recorded and analysed during increasing and decreasing phases of the temperature. The effect of ageing of the insulation on the PD patterns in oil and oil-impregnated insulation are also considered.