Abstract: The line start permanent magnet motor (LSPMM)
combines a permanent magnet rotor for a better motor efficiency
during synchronous running with an induction motor squirrel cage
rotor to permit the motor starting by direct coupling to power source.
In this paper effect of the rotor structure on a line start synchronous
permanent magnet motor (LSPMM) is analyzed. LSPMM motor with
three different structures for rotor is designed by using RMxprt
software; efficiency and line current of LSPMM motor for different
structures in full-load condition have been presented. The results
indicate that with correct choosing of rotor structure, maximum
efficiency can be found.
Abstract: Structural behavior of ring stiffened thick walled
cylinders made of functionally graded materials (FGMs) is
investigated in this paper. Functionally graded materials are inhomogeneous composites which are usually made from a mixture
of metal and ceramic. The gradient compositional variation of the
constituents from one surface to the other provides an elegant solution to the problem of high transverse shear stresses that are
induced when two dissimilar materials with large differences in material properties are bonded. FGM formation of the cylinder is
modeled by power-law exponent and the variation of characteristics is supposed to be in radial direction.
A finite element formulation is derived for the analysis. According to the property variation of the constituent materials in the radial
direction of the wall, it is not convenient to use conventional elements to model and analyze the structure of the stiffened FGM
cylinders. In this paper a new cylindrical super-element is used to model the finite element formulation and analyze the static and
modal behavior of stiffened FGM thick walled cylinders. By using
this super-element the number of elements, which are needed for
modeling, will reduce significantly and the process time is less in comparison with conventional finite element formulations. Results for static and modal analysis are evaluated and verified by
comparison to finite element formulation with conventional
elements. Comparison indicates a good conformity between results.
Abstract: An optimal power flow (OPF) based on particle swarm
optimization (PSO) was developed with more realistic generator
security constraint using the capability curve instead of only Pmin/Pmax
and Qmin/Qmax. Neural network (NN) was used in designing digital
capability curve and the security check algorithm. The algorithm is
very simple and flexible especially for representing non linear
generation operation limit near steady state stability limit and under
excitation operation area. In effort to avoid local optimal power flow
solution, the particle swarm optimization was implemented with
enough widespread initial population. The objective function used in
the optimization process is electric production cost which is
dominated by fuel cost. The proposed method was implemented at
Java Bali 500 kV power systems contain of 7 generators and 20
buses. The simulation result shows that the combination of generator
power output resulted from the proposed method was more economic
compared with the result using conventional constraint but operated
at more marginal operating point.
Abstract: Inverse kinematics analysis plays an important role in developing a robot manipulator. But it is not too easy to derive the inverse kinematic equation of a robot manipulator especially robot manipulator which has numerous degree of freedom. This paper describes an application of Artificial Neural Network for modeling the inverse kinematics equation of a robot manipulator. In this case, the robot has three degree of freedoms and the robot was implemented for drilling a printed circuit board. The artificial neural network architecture used for modeling is a multilayer perceptron networks with steepest descent backpropagation training algorithm. The designed artificial neural network has 2 inputs, 2 outputs and varies in number of hidden layer. Experiments were done in variation of number of hidden layer and learning rate. Experimental results show that the best architecture of artificial neural network used for modeling inverse kinematics of is multilayer perceptron with 1 hidden layer and 38 neurons per hidden layer. This network resulted a RMSE value of 0.01474.
Abstract: This paper features the modeling and design of a Fast
Output Sampling (FOS) Feedback control technique for the Active
Vibration Control (AVC) of a smart flexible aluminium cantilever
beam for a Single Input Single Output (SISO) case. Controllers are
designed for the beam by bonding patches of piezoelectric layer as
sensor / actuator to the master structure at different locations along
the length of the beam by retaining the first 2 dominant vibratory
modes. The entire structure is modeled in state space form using the
concept of piezoelectric theory, Euler-Bernoulli beam theory, Finite
Element Method (FEM) and the state space techniques by dividing
the structure into 3, 4, 5 finite elements, thus giving rise to three
types of systems, viz., system 1 (beam divided into 3 finite
elements), system 2 (4 finite elements), system 3 (5 finite elements).
The effect of placing the sensor / actuator at various locations along
the length of the beam for all the 3 types of systems considered is
observed and the conclusions are drawn for the best performance and
for the smallest magnitude of the control input required to control the
vibrations of the beam. Simulations are performed in MATLAB. The
open loop responses, closed loop responses and the tip displacements
with and without the controller are obtained and the performance of
the proposed smart system is evaluated for vibration control.
Abstract: A general stochastic spatial MIMO channel model is
proposed for evaluating various MIMO techniques in this paper. It can
generate MIMO channels complying with various MIMO
configurations such as smart antenna, spatial diversity and spatial
multiplexing. The modeling method produces the stochastic fading
involving delay spread, Doppler spread, DOA (direction of arrival),
AS (angle spread), PAS (power azimuth Spectrum) of the scatterers,
antenna spacing and the wavelength. It can be applied in various
MIMO technique researches flexibly with low computing complexity.
Abstract: This study aimed to detect and to identify the main
strains of airborne microorganisms present in the Shanghai Metro
system. Samples were collected using agar plates exposed to the air
and microorganisms were identified using catalase, plasma coagulase
and hymolytic analysis. The results show that the concentration of
mildew present within a newly opened metro line was significantly
higher than for other lines. Differences among underground and
elevated stations can be attributed to differences in passenger flow and
the environment surrounding the stations. Additionally, the
investigation indicated that bacteria reached maximum levels at
different times on weekdays and weekends. The bacteria in the Metro
stations were identified as primarily Gram positive, consisting mainly
of coagulase-negative staphylococcus strains (CNS).
Abstract: In India, the quarrel between the budding human
populace and the planet-s unchanging supply of freshwater and
falling water tables has strained attention the reuse of gray water as
an alternative water resource in rural development. This paper
present the finest design of laboratory scale gray water treatment
plant, which is a combination of natural and physical operations such
as primary settling with cascaded water flow, aeration, agitation and
filtration, hence called as hybrid treatment process. The economical
performance of the plant for treatment of bathrooms, basins and
laundries gray water showed in terms of deduction competency of
water pollutants such as COD (83%), TDS (70%), TSS (83%), total
hardness (50%), oil and grease (97%), anions (46%) and cations
(49%). Hence, this technology could be a good alternative to treat
gray water in residential rural area.
Abstract: This paper applies Bayesian Networks to support
information extraction from unstructured, ungrammatical, and
incoherent data sources for semantic annotation. A tool has been
developed that combines ontologies, machine learning, and
information extraction and probabilistic reasoning techniques to
support the extraction process. Data acquisition is performed with the
aid of knowledge specified in the form of ontology. Due to the
variable size of information available on different data sources, it is
often the case that the extracted data contains missing values for
certain variables of interest. It is desirable in such situations to
predict the missing values. The methodology, presented in this paper,
first learns a Bayesian network from the training data and then uses it
to predict missing data and to resolve conflicts. Experiments have
been conducted to analyze the performance of the presented
methodology. The results look promising as the methodology
achieves high degree of precision and recall for information
extraction and reasonably good accuracy for predicting missing
values.
Abstract: This study is concerned with a new adaptive impedance control strategy to compensate for unknown time-varying environment stiffness and position. The uncertainties are expressed by Function Approximation Technique (FAT), which allows the update laws to be derived easily using Lyapunov stability theory. Computer simulation results are presented to validate the effectiveness of the proposed strategy.
Abstract: There is a acute water problem especially in the dry
season in and around Perundurai (Erode district, Tamil Nadu, India)
where there are more number of tannery units. Hence an attempt was
made to use the waste water from tannery industry for construction
purpose. The mechanical properties such as compressive strength,
tensile strength, flexural strength etc were studied by casting various
concrete specimens in form of cube, cylinders and beams etc and
were found to be satisfactory. Hence some special properties such as
chloride attack, sulphate attack and chemical attack are considered
and comparatively studied with the conventional potable water. In
this experimental study the results of specimens prepared by using
treated and untreated tannery effluent were compared with the
concrete specimens prepared by using potable water. It was observed
that the concrete had some reduction in strength while subjected to
chloride attack, sulphate attack and chemical attack. So admixtures
were selected and optimized in suitable proportion to counter act the
adverse effects and the results were found to be satisfactory.
Abstract: Recently, many existing partially blind signature scheme based on a single hard problem such as factoring, discrete logarithm, residuosity or elliptic curve discrete logarithm problems. However sooner or later these systems will become broken and vulnerable, if the factoring or discrete logarithms problems are cracked. This paper proposes a secured partially blind signature scheme based on factoring (FAC) problem and elliptic curve discrete logarithms (ECDL) problem. As the proposed scheme is focused on factoring and ECDLP hard problems, it has a solid structure and will totally leave the intruder bemused because it is very unlikely to solve the two hard problems simultaneously. In order to assess the security level of the proposed scheme a performance analysis has been conducted. Results have proved that the proposed scheme effectively deals with the partial blindness, randomization, unlinkability and unforgeability properties. Apart from this we have also investigated the computation cost of the proposed scheme. The new proposed scheme is robust and it is difficult for the malevolent attacks to break our scheme.
Abstract: The join dependency provides the basis for obtaining
lossless join decomposition in a classical relational schema. The
existence of Join dependency shows that that the tables always
represent the correct data after being joined. Since the classical
relational databases cannot handle imprecise data, they were
extended to fuzzy relational databases so that uncertain, ambiguous,
imprecise and partially known information can also be stored in
databases in a formal way. However like classical databases, the
fuzzy relational databases also undergoes decomposition during
normalization, the issue of joining the decomposed fuzzy relations
remains intact. Our effort in the present paper is to emphasize on this
issue. In this paper we define fuzzy join dependency in the
framework of type-1 fuzzy relational databases & type-2 fuzzy
relational databases using the concept of fuzzy equality which is
defined using fuzzy functions. We use the fuzzy equi-join operator
for computing the fuzzy equality of two attribute values. We also
discuss the dependency preservation property on execution of this
fuzzy equi- join and derive the necessary condition for the fuzzy
functional dependencies to be preserved on joining the decomposed
fuzzy relations. We also derive the conditions for fuzzy join
dependency to exist in context of both type-1 and type-2 fuzzy
relational databases. We find that unlike the classical relational
databases even the existence of a trivial join dependency does not
ensure lossless join decomposition in type-2 fuzzy relational
databases. Finally we derive the conditions for the fuzzy equality to
be non zero and the qualification of an attribute for fuzzy key.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: This paper presents the experimental results on
artificial ageing test of 22 kV XLPE cable for distribution system
application in Thailand. XLPE insulating material of 22 kV cable
was sliced to 60-70 μm in thick and was subjected to ac high voltage
at 23
Ôùª
C, 60
Ôùª
C and 75
Ôùª
C. Testing voltage was constantly applied to
the specimen until breakdown. Breakdown voltage and time to
breakdown were used to evaluate life time of insulating material.
Furthermore, the physical model by J. P. Crine for predicts life time
of XLPE insulating material was adopted as life time model and was
calculated in order to compare the experimental results. Acceptable
life time results were obtained from Crine-s model comparing with
the experimental result. In addition, fourier transform infrared
spectroscopy (FTIR) for chemical analysis and scanning electron
microscope (SEM) for physical analysis were conducted on tested
specimens.
Abstract: It is a one-sided hypothesis testing process for assessing bioequivalence. Bootstrap and modified large-sample(MLS) methods are considered to study individual bioequivalence(IBE), type I error and power of hypothesis tests are simulated and compared with FDA(2001). The results show that modified large-sample method is equivalent to the method of FDA(2001) .
Abstract: The main goal of this paper is to study Statistical Process Control (SPC) with Exponentially Weighted Moving Average (EWMA) control chart when observations are serially-correlated. The characteristic of control chart is Average Run Length (ARL) which is the average number of samples taken before an action signal is given. Ideally, an acceptable ARL of in-control process should be enough large, so-called (ARL0). Otherwise it should be small when the process is out-of-control, so-called Average of Delay Time (ARL1) or a mean of true alarm. We find explicit formulas of ARL for EWMA control chart for Seasonal Autoregressive and Moving Average processes (SARMA) with Exponential white noise. The results of ARL obtained from explicit formula and Integral equation are in good agreement. In particular, this formulas for evaluating (ARL0) and (ARL1) be able to get a set of optimal parameters which depend on smoothing parameter (λ) and width of control limit (H) for designing EWMA chart with minimum of (ARL1).
Abstract: Xanthan gum is a microbial polysaccharide of great
commercial significance. The purpose of this study was to select the
optimum fermentation time for xanthan gum production by
Xanthomonas campestris (NRRL-B-1459) using 10% sugar beet
molasses as a carbon source. The pre-heating of sugar beet molasses
and the supplementation of the medium were investigated in order to
improve xanthan gum production. Maximum xanthan gum
production in fermentation media (9.02 g/l) was observed after 4 days
shaking incubation at 25°C and 240 rpm agitation speed. A solution
of 10% sucrose was used as a control medium. Results indicated that
the optimum period for xanthan gum production in this condition was
4 days.
Abstract: The ever increasing use of World Wide Web in the
existing network, results in poor performance. Several techniques
have been developed for reducing web traffic by compressing the size
of the file, saving the web pages at the client side, changing the burst
nature of traffic into constant rate etc. No single method was
adequate enough to access the document instantly through the
Internet. In this paper, adaptive hybrid algorithms are developed for
reducing web traffic. Intelligent agents are used for monitoring the
web traffic. Depending upon the bandwidth usage, user-s preferences,
server and browser capabilities, intelligent agents use the best
techniques to achieve maximum traffic reduction. Web caching,
compression, filtering, optimization of HTML tags, and traffic
dispersion are incorporated into this adaptive selection. Using this
new hybrid technique, latency is reduced to 20 – 60 % and cache hit
ratio is increased 40 – 82 %.
Abstract: Recently, it has been suggested that thought control strategies aimed at controlling unwanted thoughts may be used to cope with paranoid thoughts in both clinical and nonclinical samples. The current study aims to examine the type of thought control strategies that were associated with the frequency of paranoid thoughts in nonclinical samples. A total of 159 Japanese undergraduate students completed the two scales–the Paranoia Checklist and the Thought Control Questionnaire. A hierarchical multiple regression analysis demonstrated that worry-based control strategies were associated with paranoid thoughts, whereas distraction- and social-based control strategies were inversely associated with paranoid thoughts. Our findings suggest that in a nonclinical population, worry-based strategies may be especially maladaptive, whereas distraction- and social-based strategies may be adaptive to paranoid thoughts.