Abstract: Sulfide ion (S2-) is one of the most important ions to be
monitored due to its high toxicity, especially for aquatic organisms. In
this work, [Ca(2,2'-bipyridine)3]2+-intercalated montmorillonite was
prepared and used as a sensor to construct a potentiometric electrode to
measure sulfide ion in solution. The formation of [Ca(2,2'-
bipyridine)3]2+ in montmorillonite was confirmed by Fourier Transform
Infrared spectra. The electrode worked well at pH 4-12 and 4-10 in
sulfide solution 10-2 M and 10-3 M, respectively, in terms of Nernstian
slope. The sensor gave good precision and low cost.
Abstract: The systematic manipulations of shapes and sizes of
inorganic compounds greatly benefit the various application fields
including optics, magnetic, electronics, catalysis and medicine.
However shape control has been much more difficult to achieve.
Hence exploration of novel method for the preparation of differently
shaped nanoparticles is challenging research area. II-VI group of
semiconductor cadmium sulphide (CdS) nanostructure with different
morphologies (such as, acicular like, mesoporous, spherical shapes)
and of crystallite sizes vary from 11 to 16 nm were successfully
synthesized by chemical aqueous precipitation of Cd2+ ions with
homogeneously released S2- ions from decomposition of cadmium
sulphate (CdSO4) and thioacetamide (CH3CSNH2) by annealing at
different radiations (microwave, ultrasonic and sunlight) with matter
and systematic research has been done for various factors affecting
the controlled growth rate of CdS nanoparticles. The obtained
nanomaterials have been characterized by X-ray Diffraction (XRD),
Fourier Transform Infrared Spectroscopy (FTIR),
Thermogravometric (DSC-TGA) analysis and Scanning Electron
Microscopy (SEM). The result indicates that on increasing the
reaction time particle size increases but on increasing the molar ratios
grain size decreases.
Abstract: In this paper the combination of thermal oxidation and
electrochemical anodizing processes is used to produce titanium
oxide layers. The response of titanium alloy Ti6Al4V to oxidation
processes at various temperatures and electrochemical anodizing in
various voltages are investigated. Scanning electron microscopy
(SEM); X-Ray Diffraction (XRD) and porosity determination have
been used to characterize the oxide layer thickness, surface
morphology, oxide layer-substrate adhesion and porosity. In the first
experiment, samples modified by thermal oxidation process then
followed by electrochemical anodizing. Second experiment consists
of surfaces modified by electrochemical anodizing process and then
followed by thermal oxidation. The first method shows better
properties than other one. In second experiment, Surfaces modified
were achieved by thicker and more adherent thick oxide layers on
titanium surface. The existence of an electrochemical anodized oxide
layer did not improve the adhesion of thermal oxide layer. The high
temperature, thermal formation of an oxide layer leads to a coarse
oxide grain morphology and a complete oxidative particle. In
addition, in high temperature oxidation porosity content is increased.
The oxide layer of thermal oxidation and electrochemical anodizing
processes; on Ti–6Al–4V substrate was covered with different
colored oxide layers.
Abstract: The remediation of water resources pollution in
developing countries requires the application of alternative
sustainable cheaper and efficient end-of-pipe wastewater treatment
technologies. The feasibility of use of South African cheap and
abundant pine tree (Pinus patula) sawdust for development of lowcost
AC of comparable quality to expensive commercial ACs in the
abatement of water pollution was investigated. AC was developed at
optimized two-stage N2-superheated steam activation conditions in a
fixed bed reactor, and characterized for proximate and ultimate
properties, N2-BET surface area, pore size distribution, SEM, pHPZC
and FTIR. The sawdust pyrolysis activation energy was evaluated by
TGA. Results indicated that the chars prepared at 800oC and 2hrs
were suitable for development of better quality AC at 800oC and 47%
burn-off having BET surface area (1086m2/g), micropore volume
(0.26cm3/g), and mesopore volume (0.43cm3/g) comparable to
expensive commercial ACs, and suitable for water contaminants
removal. The developed AC showed basic surface functionality at
pHPZC at 10.3, and a phenol adsorption capacity that was higher than
that of commercial Norit (RO 0.8) AC. Thus, it is feasible to develop
better quality low-cost AC from (Pinus patula) sawdust using twostage
N2-steam activation in fixed-bed reactor.
Abstract: The effects of equilibrium time, solution pH, and
sorption temperature of cationic methylene blue (MB) adsorption on nanoporous metallosilicoaluminophosphate ZnAPSO-34 was studied
using a batch equilibration method. UV–VIS spectroscopy was used
to obtain the adsorption isotherms at 20° C. The optimum period for
adsorption was 300 min. However, MB removal increased from
81,82 % to 94,81 %. The equilibrium adsorption data was analyzed
by using Langmuir, Freundlich and Temkin isotherm models.
Langmuir isotherm was found to be the better-fitting model and the process followed pseudo second–order kinetics. The results showed
that ZnAPSO-34 could be employed as an effective material and could be an attractive alternative for the removal of dyes and colors
from aqueous solutions.
Abstract: The objective of this work is to show a procedure for
mesh generation in a fluidized bed using large eddy simulations
(LES) of a filtered two-fluid model. The experimental data were
obtained by [1] in a laboratory fluidized bed. Results show that it is
possible to use mesh with less cells as compared to RANS turbulence
model with granular kinetic theory flow (KTGF). Also, the numerical
results validate the experimental data near wall of the bed, which
cannot be predicted by RANS.model.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Carbon fibers are fabricated from different materials,
such as special polyacrylonitrile (PAN) fibers, rayon fibers and pitch.
Among these three groups of materials, PAN fibers are the most
widely used precursor for the manufacture of carbon fibers. The
process of fabrication carbon fibers from special PAN fibers includes
two steps; oxidative stabilization at low temperature and
carbonization at high temperatures in an inert atmosphere. Due to the
high price of raw materials (special PAN fibers), carbon fibers are
still expensive.
In the present work the main goal is making carbon fibers from
low price commercial PAN fibers with modified chemical
compositions. The results show that in case of conducting completes
stabilization process, it is possible to produce carbon fibers with
desirable tensile strength from this type of PAN fibers. To this
matter, thermal characteristics of commercial PAN fibers were
investigated and based upon the obtained results, with some changes
in conventional procedure of stabilization in terms of temperature
and time variables; the desirable conditions of complete stabilization
is achieved.
Abstract: An effect of rolling temperature on the mechanical properties and microstructural evolution of an Al-Mg-Si alloy was studied. The material was rolled up to a true strain of ~0.7 at three different temperatures viz; room temperature, liquid propanol and liquid nitrogen. The liquid nitrogen rolled sample exhibited superior properties with a yield and tensile strength of 332 MPa and 364 MPa, respectively, with a reasonably good ductility of ~9%. The liquid nitrogen rolled sample showed around 54 MPa increase in tensile strength without much reduction in the ductility as compared to the as received T6 condition alloy. The microstructural details revealed equiaxed grains in the annealed and solutionized sample and elongated grains in the rolled samples. In addition, the cryorolled samples exhibited fine grain structure compared to the room temperature rolled samples.
Abstract: The present work presents the extraction of copper(II)
from sulphuric acid solutions with Sodium diethyldithiocarbamate
(SDDT), and six different organic diluents: Dichloromethane,
Chloroform, Carbon tetrachloride, Toluene, xylene and Cyclohexane,
were tested. The pair SDDT/Chloroform showed to be the most
selective in removing the copper cations, and hence was considered
throughout the experimental study.
The effects of operating parameters such as the initial concentration
of the extracting agent, the agitation time, the agitation speed and the
acid concentration were considered.
For an initial concentration of Cu (II) of 63 ppm in a 0.5 M sulphuric
acid solution, both with a mass of the extracting agent of 20 mg, an
extraction percentage of about 97.8 % and a distribution coefficient
of 44.42 were obtained, respectively, confirming the performance
of the SDDT-Chloroform pair.
Abstract: Calcium is very important for communication among
the neurons. It is vital in a number of cell processes such as secretion,
cell movement, cell differentiation. To reduce the system of reactiondiffusion
equations of [Ca2+] into a single equation, two theories
have been proposed one is excess buffer approximation (EBA) other
is rapid buffer approximation (RBA). The RBA is more realistic than
the EBA as it considers both the mobile and stationary endogenous
buffers. It is valid near the mouth of the channel. In this work we have
studied the effects of different types of buffers on calcium diffusion
under RBA. The novel thing studied is the effect of sodium ions on
calcium diffusion. The model has been made realistic by considering
factors such as variable [Ca2+], [Na+] sources, sodium-calcium
exchange protein(NCX), Sarcolemmal Calcium ATPase pump. The
proposed mathematical leads to a system of partial differential equations
which has been solved numerically to study the relationships
between different parameters such as buffer concentration, buffer
disassociation rate, calcium permeability. We have used Forward
Time Centred Space (FTCS) approach to solve the system of partial
differential equations.
Abstract: Analysis for the generalized thermoelastic Lamb
waves, which propagates in anisotropic thin plates in generalized
thermoelasticity, is presented employing normal mode expansion
method. The displacement and temperature fields are expressed by a
summation of the symmetric and antisymmetric thermoelastic modes
in the surface thermal stresses and thermal gradient free orthotropic
plate, therefore the theory is particularly appropriate for waveform
analyses of Lamb waves in thin anisotropic plates. The transient
waveforms excited by the thermoelastic expansion are analyzed for
an orthotropic thin plate. The obtained results show that the theory
provides a quantitative analysis to characterize anisotropic
thermoelastic stiffness properties of plates by wave detection. Finally
numerical calculations have been presented for a NaF crystal, and the
dispersion curves for the lowest modes of the symmetric and
antisymmetric vibrations are represented graphically at different
values of thermal relaxation time. However, the methods can be used
for other materials as well
Abstract: It is estimated that the total cost of abnormal
conditions to US process industries is around $20 billion dollars in
annual losses. The hydrotreatment (HDT) of diesel fuel in petroleum
refineries is a conversion process that leads to high profitable
economical returns. However, this is a difficult process to control
because it is operated continuously, with high hydrogen pressures
and it is also subject to disturbances in feed properties and catalyst
performance. So, the automatic detection of fault and diagnosis plays
an important role in this context. In this work, a hybrid approach
based on neural networks together with a pos-processing
classification algorithm is used to detect faults in a simulated HDT
unit. Nine classes (8 faults and the normal operation) were correctly
classified using the proposed approach in a maximum time of 5
minutes, based on on-line data process measurements.
Abstract: spherical porous carbon particles with
controllable porosity with a mean size of 2.5m have been
prepared using a spray drying method with organic particle
colloidal template. As a precursor, a mixing solution of carbon
nanopowder and polystyrene (PS) particles as a template was
used. The result showed that the particles with a good porous
structure could be obtained. The pore size and shape (spherical)
were identical to the initial template, giving a potential way for
further developments. The control of particle porosity was also
possible and reported in this paper, in which this control could
be achieved by means of PS concentration.
Abstract: This paper present a new way to find the aerodynamic
characteristic equation of missile for the numerical trajectories
prediction more accurate. The goal is to obtain the polynomial
equation based on two missile characteristic parameters, angle of
attack (α ) and flight speed (ν ). First, the understudied missile is
modeled and used for flow computational model to compute
aerodynamic force and moment. Assume that performance range of
understudied missile where range -10< α
Abstract: Lignocellulosic materials are considered the most
abundant renewable resource available for the Bioethanol
Production. Water Hyacinth is one of potential raw material of the
world-s worst aquatic plant as a feedstock to produce Bioethanol.
The purposed this research is obtain reduced of matter for
biodegradation lignin in Biological pretreatment with White Rot
Fungi eg. Phanerochaete Chrysosporium using Solid state
Fermentation methods. Phanerochaete Chrysosporium is known to
have the best ability to degraded lignin, but simultaneously it can also
degraded cellulose and hemicelulose. During 8 weeks incubation,
water hyacinth occurred loss of weight reached 34,67%, while loss
of lignin reached 67,21%, loss of cellulose reached 11,01% and loss
of hemicellulose reached 36,56%. The kinetic of losses lignin using
regression linear plot, the results is obtained constant rate (k) of
reduction lignin is -0.1053 and the equation of reduction of lignin
is y = wo - 0, 1.53 x
Abstract: Construction of portable device for fast analysis of energetic materials is described in this paper. The developed analytical system consists of two main parts: a miniaturized microcolumn liquid chromatograph of unique construction and original chemiluminescence detector. This novel portable device is able to determine selectively most of nitramine- and nitroester-based explosives as well as inorganic nitrates at trace concentrations in water or soil extracts in less than 8 minutes.
Abstract: The use of amine mixtures employing
methyldiethanolamine (MDEA), monoethanolamine (MEA), and diethanolamine (DEA) have been investigated for a variety of cases
using a process simulation program called HYSYS. The results show that, at high pressures, amine mixtures have little or no advantage in the cases studied. As the pressure is lowered, it becomes more difficult for MDEA to meet residual gas requirements and mixtures can usually improve plant performance. Since the CO2 reaction rate
with the primary and secondary amines is much faster than with
MDEA, the addition of small amounts of primary or secondary amines to an MDEA based solution should greatly improve the overall reaction rate of CO2 with the amine solution. The addition of MEA caused the CO2 to be absorbed more strongly in the upper portion of the column than for MDEA along. On the other hand,
raising the concentration for MEA to 11%wt, CO2 is almost
completely absorbed in the lower portion of the column. The addition of MEA would be most advantageous.
Thus, in areas where MDEA cannot meet the residual gas
requirements, the use of amine mixtures can usually improve the plant
performance.
Abstract: Localized surface plasmon resonance (LSPR) is the
coherent oscillation of conductive electrons confined in noble
metallic nanoparticles excited by electromagnetic radiation, and
nanosphere lithography (NSL) is one of the cost-effective methods to
fabricate metal nanostructures for LSPR. NSL can be categorized
into two major groups: dispersed NSL and closely pack NSL. In
recent years, gold nanocrescents and gold nanoholes with vertical
sidewalls fabricated by dispersed NSL, and silver nanotriangles and
gold nanocaps on silica nanospheres fabricated by closely pack NSL,
have been reported for LSPR biosensing. This paper introduces
several novel gold nanostructures fabricated by NSL in LSPR
applications, including 3D nanostructures obtained by evaporating
gold obliquely on dispersed nanospheres, nanoholes with slant
sidewalls, and patchy nanoparticles on closely packed nanospheres,
all of which render satisfactory sensitivity for LSPR sensing. Since
the LSPR spectrum is very sensitive to the shape of the metal
nanostructures, formulas are derived and software is developed for
calculating the profiles of the obtainable metal nanostructures by
NSL, for different nanosphere masks with different fabrication
conditions. The simulated profiles coincide well with the profiles of
the fabricated gold nanostructures observed under scanning electron
microscope (SEM) and atomic force microscope (AFM), which
proves that the software is a useful tool for the process design of
different LSPR nanostructures.