Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: Polystyrene particles of different sizes are optically
trapped with a gaussian beam from a He-Cd laser operating at 442
nm. The particles are observed to exhibit luminescence after a certain
trapping time followed by an escape from the optical trap. The
observed luminescence is explained in terms of the photodegradation
of the polystyrene backbone. It is speculated that these chemical
modifications also play a role for the escape of the particles from the
trap. Variations of the particle size and the laser power show that
these parameters have a great influence on the observed phenomena.
Abstract: A theoretical study is conducted to design and explore
the effect of different parameters such as heat loads, the tube size of
piping system, wick thickness, porosity and hole size on the
performance and capability of a Loop Heat Pipe(LHP). This paper
presents a steady state model that describes the different phenomena
inside a LHP. Loop Heat Pipes(LHPs) are two-phase heat transfer
devices with capillary pumping of a working fluid. By their original
design comparing with heat pipes and special properties of the
capillary structure, they-re capable of transferring heat efficiency for
distances up to several meters at any orientation in the gravity field,
or to several meters in a horizontal position. This theoretical model is
described by different relations to satisfy important limits such as
capillary and nucleate boiling. An algorithm is developed to predict
the size of the LHP satisfying the limitations mentioned above for a
wide range of applied loads. Finally, to assess and evaluate the
algorithm and all the relations considered, we have used to design a
new kind of LHP to recover the heat from the exhaust of an actual
Gas Turbine. By finding the results, it showed that we can use the
LHP as a very high efficient device to recover the heat even in high
amount of loads(exhaust of a gas turbine). The sizes of all parts of the
LHP were obtained using the developed algorithm.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: The automatic transmission (AT) is one of the most
important components of many automobile transmission systems. The
shift quality has a significant influence on the ride comfort of the
vehicle. During the AT shift process, the joint elements such as the
clutch and bands engage or disengage, linking sets of gears to create a
fixed gear ratio. Since these ratios differ between gears in a fixed gear
ratio transmission, the motion of the vehicle could change suddenly
during the shift process if the joint elements are engaged or disengaged
inappropriately, additionally impacting the entire transmission system
and increasing the temperature of connect elements.The objective was
to establish a system model for an AT powertrain using
Matlab/Simulink. This paper further analyses the effect of varying
hydraulic pressure and the associated impact on shift quality during
both engagment and disengagement of the joint elements, proving that
shift quality improvements could be achieved with appropriate
hydraulic pressure control.
Abstract: the intension in this work is to investigate the effect of
different bending manifold pipes on engine performance for different
engine speed. Power, Torque, and BSFC were calculated and
presented to show the effect of varying bending pipes angles on them
for all cases considered. A special program used to carry out the
calculations. A simulation model for 4-cylinders spark ignition
engine with turbocharger has been built and calculated. The analysis
of the results shows that for 120o angle the torque increases about
40% at 3000 rpm and 25% at 4000 rpm without changing in fuel
consumption. For 90o angle the increment in torque is about 10 %.
For the same bending angle the increment in brake power is around
40% at 3000 rpm and 25% at 4000 rpm. The increment in fuel
consumption is about 12% for 60o and 30% for 90o between (6000-
7000) rpm.
Abstract: In this paper, a new approach is introduced to solve
Blasius equation using parameter identification of a nonlinear
function which is used as approximation function. Bees Algorithm
(BA) is applied in order to find the adjustable parameters of
approximation function regarding minimizing a fitness function
including these parameters (i.e. adjustable parameters). These
parameters are determined how the approximation function has to
satisfy the boundary conditions. In order to demonstrate the
presented method, the obtained results are compared with another
numerical method. Present method can be easily extended to solve a
wide range of problems.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: In this research, the use of light beam size to design the adjustable mirror bender is presented. The focused beam line characterized by its size towards the synchrotron light beam line is investigated. The COSMOSWorks is used in all simulation components of curvature adjustment system to analyze in finite element method. The results based on simulation covers the use of applied forces during adjustment of the mirror radius are presented.
Abstract: Active vibration control is an important problem in
structures. The objective of active vibration control is to reduce the vibrations of a system by automatic modification of the system-s
structural response. In this paper, the modeling and design of a fast
output sampling feedback controller for a smart flexible beam system embedded with shear sensors and actuators for SISO system using
Timoshenko beam theory is proposed. FEM theory, Timoshenko beam theory and the state space techniques are used to model the
aluminum cantilever beam. For the SISO case, the beam is divided into 5 finite elements and the control actuator is placed at finite
element position 1, whereas the sensor is varied from position 2 to 5, i.e., from the nearby fixed end to the free end. Controllers are
designed using FOS method and the performance of the designed FOS controller is evaluated for vibration control for 4 SISO models
of the same plant. The effect of placing the sensor at different locations on the beam is observed and the performance of the
controller is evaluated for vibration control. Some of the limitations of the Euler-Bernoulli theory such as the neglection of shear and
axial displacement are being considered here, thus giving rise to an accurate beam model. Embedded shear sensors and actuators have
been considered in this paper instead of the surface mounted sensors
and actuators for vibration suppression because of lot of advantages. In controlling the vibration modes, the first three dominant modes of
vibration of the system are considered.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: The objective of this study is to investigate the
combustion in a pilot-ignited supercharged dual-fuel engine, fueled
with different types of gaseous fuels under various equivalence ratios.
It is found that if certain operating conditions are maintained,
conventional dual-fuel engine combustion mode can be transformed to
the combustion mode with the two-stage heat release. This mode of
combustion was called the PREMIER (PREmixed Mixture Ignition in
the End-gas Region) combustion. During PREMIER combustion,
initially, the combustion progresses as the premixed flame
propagation and then, due to the mixture autoignition in the end-gas
region, ahead of the propagating flame front, the transition occurs with
the rapid increase in the heat release rate.
Abstract: Modularized design approach can facilitate the
modeling of complex systems and support behavior analysis and
simulation in an iterative and thus complex engineering process, by
using encapsulated submodels of components and of their interfaces.
Therefore it can improve the design efficiency and simplify the
solving complicated problem. Multi-drivers off-road vehicle is
comparatively complicated. Driving-line is an important core part to a
vehicle; it has a significant contribution to the performance of a
vehicle. Multi-driver off-road vehicles have complex driving-line, so
its performance is heavily dependent on the driving-line. A typical
off-road vehicle-s driving-line system consists of torque converter,
transmission, transfer case and driving-axles, which transfer the
power, generated by the engine and distribute it effectively to the
driving wheels according to the road condition. According to its main
function, this paper puts forward a modularized approach for
designing and evaluation of vehicle-s driving-line. It can be used to
effectively estimate the performance of driving-line during concept
design stage. Through appropriate analysis and assessment method, an
optimal design can be reached. This method has been applied to the
practical vehicle design, it can improve the design efficiency and is
convenient to assess and validate the performance of a vehicle,
especially of multi-drivers off-road vehicle.
Abstract: This paper deals with the design of a moving sliding
surface in a variable structure plant for a second order system. The
chattering phenomena is also dealt with during the switching process
for an unstable sliding surface condition. The simulation examples
considered in this paper shows the effectiveness of the sliding mode
control method used for the design of the moving sliding surfaces. A
simulink model of the continuous system was also developed in
MATLAB-SIMULINK for the design and hence demonstrated. The
phase portraits and the state plots shows the demonstration of
the powerful control technique which can be applied for second
order systems.
Abstract: In industry, on of the most important subjects is die
and it's characteristics in which for cutting and forming different
mechanical pieces, various punch and matrix metal die are used.
whereas the common parts which form the main frame die are not
often proportion with pieces and dies therefore using a part as socalled
common part for frames in specified dimension ranges can
decrease the time of designing, occupied space of warehouse and
manufacturing costs. Parts in dies with getting uniform in their shape
and dimension make common parts of dies. Common parts of punch
and matrix metal die are as bolster, guide bush, guide pillar and
shank. In this paper the common parts and effective parameters in
selecting each of them as the primary information are studied,
afterward for selection and design of mechanical parts an
introduction and investigation based on the Mech. Desk. software is
done hence with developing this software can standardize the metal
common parts of punch and matrix. These studies will be so useful
for designer in their designing and also using it has with very much
advantage for manufactures of products in decreasing occupied
spaces by dies.