Abstract: In this paper a novel, simple and reliable digital firing
scheme has been implemented for speed control of three-phase
induction motor using ac voltage controller. The system consists of
three-phase supply connected to the three-phase induction motor via
three triacs and its control circuit. The ac voltage controller has three
modes of operation depending on the shape of supply current. The
performance of the induction motor differs in each mode where the
speed is directly proportional with firing angle in two modes and
inversely in the third one. So, the control system has to detect the
current mode of operation to choose the correct firing angle of triacs.
Three sensors are used to feed the line currents to control system to
detect the mode of operation. The control strategy is implemented
using a low cost Xilinx Spartan-3E field programmable gate array
(FPGA) device. Three PI-controllers are designed on FPGA to
control the system in the three-modes. Simulation of the system is
carried out using PSIM computer program. The simulation results
show stable operation for different loading conditions especially in
mode 2/3. The simulation results have been compared with the
experimental results from laboratory prototype.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: In the present paper the displacement-based nonconforming quadrilateral affine thin plate bending finite element ARPQ4 is presented, derived directly from non-conforming quadrilateral thin plate bending finite element RPQ4 proposed by Wanji and Cheung [19]. It is found, however, that element RPQ4 is only conditionally unisolvent. The new element is shown to be inherently unisolvent. This convenient property results in the element ARPQ4 being more robust and thus better suited for computations than its predecessor. The convergence is proved and the rate of convergence estimated. The mathematically rigorous proof of convergence presented in the paper is based on Stummel-s generalized patch test and the consideration of the element approximability condition, which are both necessary and sufficient for convergence.
Abstract: the paper presents the optimization results for several
electrical machines dedicated for powered electric wheel-chairs. The
optimization, using the Hook-Jeeves algorithm, was employed based
on a design approach which takes into consideration the road
conditions. Also, through numerical simulations (based on finite
element method), the analytical approach was validated. The
optimization approach gave satisfactory results and the best suited
variant was chosen for the motorization of the wheel-chair.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: A two-dimensional thin-walled capsule of a flexible
semi-permeable membrane is adhered onto a rigid planar substrate
under adhesive forces (derived from a potential function) in the
presence of osmosis across the membrane. The capsule is immersed
in a hypotonic and diluted binary solution of a non-electrolyte
solute. The Stokes flow problem is solved by the immersed interface
method (IIM) with equal viscosities for the enclosed and
surrounding fluid of the capsule. The numerical results obtained are
verified against two simplified theoretical solutions and the
agreements are good. The osmotic inflation of the adhered capsule is
studied as a function of the solute concentration field, hydraulic
conductivity, and the initial capsule shape. Our findings indicate that
the contact length shrinks in dimension as capsule inflates in the
hypotonic medium, and the equilibrium contact length does not
depend on the hydraulic conductivity of the membrane and the
initial shape of the capsule.
Abstract: This paper studies mechanical buckling of
functionally graded beams subjected to axial compressive load that is
simply supported at both ends lies on a continuous elastic foundation.
The displacement field of beam is assumed based on Engesser-Timoshenko beam theory. Applying the Hamilton's principle, the
equilibrium equation is established. The influences of dimensionless geometrical parameter, functionally graded index and foundation
coefficient on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: In this work, we try to find the best setting
of Computational Fluid Dynamic solver available for the problems in
the field of supersonic internal flows. We used the supersonic air-toair
ejector to represent the typical problem in focus. There are
multiple oblique shock waves, shear layers, boundary layers
and normal shock interacting in the supersonic ejector making this
device typical in field of supersonic inner flows. Modeling of shocks
in general is demanding on the physical model of fluid, because
ordinary conservation equation does not conform to real conditions in
the near-shock region as found in many works. From these reasons,
we decided to take special care about solver setting in this article by
means of experimental approach of color Schlieren pictures and
pneumatic measurement. Fast pressure transducers were used to
measure unsteady static pressure in regimes with normal shock in
mixing chamber. Physical behavior of ejector in several regimes is
discussed. Best choice of eddy-viscosity setting is discussed on the
theoretical base. The final verification of the k-ω SST is done on the
base of comparison between experiment and numerical results.
Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.
Abstract: This research proposes the change of damping coefficient regarding minimum displacement. From the mass with external forced and damper problem, when is the constant external forced transmitted to the understructure in the difference angle between 30 and 60 degrees. This force generates the vibration as general known; however, the objective of this problem is to have minimum displacement. As the angle is changed and the goal is the same; therefore, the damper of the system must be varied while keeping constant spring stiffness. The problem is solved by using nonlinear programming and the suitable changing of the damping coefficient is provided.
Abstract: A numerical method is proposed to calculate damping
properties for sound-proof structures involving elastic body,
viscoelastic body, and porous media. For elastic and viscoelastic body
displacement is modeled using conventional finite elements including
complex modulus of elasticity. Both effective density and bulk
modulus have complex quantities to represent damped sound fields in
the porous media. Particle displacement in the porous media is
discretised using finite element method. Displacement vectors as
common unknown variables are solved under coupled condition
between elastic body, viscoelastic body and porous media. Further,
explicit expressions of modal loss factor for the mixed structures are
derived using asymptotic method. Eigenvalue analysis and frequency
responded were calculated for automotive test panel laminated
viscoelastic and porous structures using this technique, the results
almost agreed with the experimental results.
Abstract: This paper proposes method of diagnosing ball screw
preload loss through the Hilbert-Huang Transform （HHT） and
Multiscale entropy （MSE） process. The proposed method can
diagnose ball screw preload loss through vibration signals when the
machine tool is in operation. Maximum dynamic preload of 2 %, 4 %,
and 6 % ball screws were predesigned, manufactured, and tested
experimentally. Signal patterns are discussed and revealed using
Empirical Mode Decomposition（EMD）with the Hilbert Spectrum.
Different preload features are extracted and discriminated using HHT.
The irregularity development of a ball screw with preload loss is
determined and abstracted using MSE based on complexity
perception. Experiment results show that the proposed method can
predict the status of ball screw preload loss. Smart sensing for the
health of the ball screw is also possible based on a comparative
evaluation of MSE by the signal processing and pattern matching of
EMD/HHT. This diagnosis method realizes the purposes of prognostic
effectiveness on knowing the preload loss and utilizing convenience.
Abstract: A kind of crash energy absorption structure adopted by vehicle simulator crash testing equipment based on mechanical energy
storage was studied. Dynamic explicit finite element simulation was achieved for thin-walled tube structure under different conditions of
section shape, thickness and inducement groove style. Crash energy absorption property of the structure was obtained. After optimization,
a reasonable structure was given which can meet current vehicle crash regulation. And the optimized structure can be adopted in vehicle
simulator, which can increase the practicability of the testing
equipment.
Abstract: The impeller and the casing are the key components of
a centrifugal pump. Although there have been many studies on the
impeller and the volute casing of centrifugal pump, further study of the
volute casing to improve the performance of centrifugal pumps is
needed. In this paper, the effect of cross-sectional area on the
performance of volute casing was investigated using a commercial
CFD code. The performance characteristics, not only at the off-design
point but also for a full type model are required these days. So we
conducted numerical analysis for all operating points by using
complete geometry through transient analysis. Transient analysis on
the complete geometry of a real product has the advantage of
simulating realistic flow. The results of this study show the variation of
a performance curve by modifying the above-mentioned design
parameter.
Abstract: In this paper a sliding-mode torque and flux control is
designed for encoderless synchronous reluctance motor drive. The
sliding-mode plus PI controllers are designed in the stator-flux field
oriented reference frame which is able to track the mentioned
reference signals with a minimum pulsations in the state condition. In
addition, with these controllers a fast dynamic response is also
achieved for the drive system. The proposed control scheme is robust
subject to parameters variation except to stator resistance. To solve
this problem a simple estimator is used for on-line detecting of this
parameter. Moreover, the rotor position and speed are estimated by
on-line obtaining of the stator-flux-space vector. The effectiveness
and capability of the proposed control approach is verified by both
the simulation and experimental results.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free and clamped-clamped boundary conditions.