Abstract: In the micro and nano-technology industry, the
«clean-rooms» dedicated to manufacturing chip, are equipped with
the most sophisticated equipment-tools. There use a large number of
resources in according to strict specifications for an optimum
working and result. The distribution of «utilities» to the production is
assured by teams who use a supervision tool.
The studies show the interest to control the various parameters of
production or/and distribution, in real time, through a reliable and
effective supervision tool. This document looks at a large part of the
functions that the supervisor must assure, with complementary
functionalities to help the diagnosis and simulation that prove very
useful in our case where the supervised installations are complexed
and in constant evolution.
Abstract: Composite steel-concrete slabs using thin-walled
corrugated steel sheets with embossments represent a modern and
effective combination of steel and concrete. However, the design
of new types of sheeting is conditional on the execution of expensive
and time-consuming laboratory testing. The effort to develop
a cheaper and faster method has lead to many investigations all over
the world. In our paper we compare the results from our experiments
involving vacuum loading, four-point bending and small-scale shear
tests.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: A method based on the power series solution is proposed to solve the natural frequency of flapping vibration for the rotating inclined Euler beam with constant angular velocity. The vibration of the rotating beam is measured from the position of the corresponding steady state axial deformation. In this paper the governing equations for linear vibration of a rotating Euler beam are derived by the d'Alembert principle, the virtual work principle and the consistent linearization of the fully geometrically nonlinear beam theory in a rotating coordinate system. The governing equation for flapping vibration of the rotating inclined Euler beam is linear ordinary differential equation with variable coefficients and is solved by a power series with four independent coefficients. Substituting the power series solution into the corresponding boundary conditions at two end nodes of the rotating beam, a set of homogeneous equations can be obtained. The natural frequencies may be determined by solving the homogeneous equations using the bisection method. Numerical examples are studied to investigate the effect of inclination angle on the natural frequency of flapping vibration for rotating inclined Euler beams with different angular velocity and slenderness ratio.
Abstract: In this paper, the steady-state temperature of a sample 500 KW two rotor one stator Non-slotted axial flux permanent magnet motor is calculated using the finite element simulator software package. Due to the high temperature in various parts of the machine, especially at stator winding, a cooling system is designed for the motor and the temperature is recalculated. The results show that the temperature obtained for the parts is within the permissible range.
Abstract: The paper considers a novel modular and intrinsically safe redundant robotic system with biologically inspired actuators (pneumatic artificial muscles and rubber bellows actuators). Similarly to the biological systems, the stiffness of the internal parallel modules, representing 2 DOF joints in the serial robotic chains, is controlled by co-activation of opposing redundant actuator groups in the null-space of the module Jacobian, without influencing the actual robot position. The decoupled position/stiffness control allows the realization of variable joint stiffness according to different force-displacement relationships. The variable joint stiffness, as well as limited pneumatic muscle/bellows force ability, ensures internal system safety that is crucial for development of human-friendly robots intended for human-robot collaboration. The initial experiments with the system prototype demonstrate the capabilities of independently, simultaneously controlling both joint (Cartesian) motion and joint stiffness. The paper also presents the possible industrial applications of snake-like robots built using the new modules.
Abstract: A reduced order modeling approach for natural
gas transient flow in pipelines is presented. The Euler
equations are considered as the governing equations and
solved numerically using the implicit Steger-Warming flux
vector splitting method. Next, the linearized form of the
equations is derived and the corresponding eigensystem is
obtained. Then, a few dominant flow eigenmodes are used to
construct an efficient reduced-order model. A well-known test
case is presented to demonstrate the accuracy and the
computational efficiency of the proposed method. The results
obtained are in good agreement with those of the direct
numerical method and field data. Moreover, it is shown that
the present reduced-order model is more efficient than the
conventional numerical techniques for transient flow analysis
of natural gas in pipelines.
Abstract: In this paper; we are interested principally in dynamic modelling of quadrotor while taking into account the high-order nonholonomic constraints in order to develop a new control scheme as well as the various physical phenomena, which can influence the dynamics of a flying structure. These permit us to introduce a new state-space representation. After, the use of Backstepping approach for the synthesis of tracking errors and Lyapunov functions, a sliding mode controller is developed in order to ensure Lyapunov stability, the handling of all system nonlinearities and desired tracking trajectories. Finally simulation results are also provided in order to illustrate the performances of the proposed controller.
Abstract: In this paper, a simulated annealing algorithm has been developed to optimize machining parameters in turning operation on cylindrical workpieces. The turning operation usually includes several passes of rough machining and a final pass of finishing. Seven different constraints are considered in a non-linear model where the goal is to achieve minimum total cost. The weighted total cost consists of machining cost, tool cost and tool replacement cost. The computational results clearly show that the proposed optimization procedure has considerably improved total operation cost by optimally determining machining parameters.
Abstract: In this study the mixed convection heat transfer in a
coil-in-shell heat exchanger for various Reynolds numbers and
various dimensionless coil pitch was experimentally investigated.
The experiments were conducted for both laminar and turbulent flow
inside coil and the effects of coil pitch on shell-side heat transfer
coefficient of the heat exchanger were studied. The particular
difference in this study in comparison with the other similar studies
was the boundary conditions for the helical coils. The results indicate
that with the increase of coil pitch, shell-side heat transfer coefficient
is increased.
Abstract: This paper investigates the occurrence of regenerative
chatter vibrations in facing and turning processes. Orthogonal turning
(facing) and normal turning experiments are carried out under stable
as well as in the presence of controlled chatter vibrations. The effects
of chatter vibrations on various sensor signals are captured and
analyzed using frequency domain methods, which successfully
detected the chatter vibrations close to the dominant mode of the
machine tool system.
Abstract: Pipeline infrastructures normally represent high cost of investment and the pipeline must be free from risks that could cause environmental hazard and potential threats to personnel safety. Pipeline integrity such monitoring and management become very crucial to provide unimpeded transportation and avoiding unnecessary production deferment. Thus proper cleaning and inspection is the key to safe and reliable pipeline operation and plays an important role in pipeline integrity management program and has become a standard industry procedure. In view of this, understanding the motion (dynamic behavior), prediction and control of the PIG speed is important in executing pigging operation as it offers significant benefits, such as estimating PIG arrival time at receiving station, planning for suitable pigging operation, and improves efficiency of pigging tasks. The objective of this paper is to review recent developments in speed control system of pipeline PIGs. The review carried out would serve as an industrial application in a form of quick reference of recent developments in pipeline PIG speed control system, and further initiate others to add-in/update the list in the future leading to knowledge based data, and would attract active interest of others to share their view points.
Abstract: Automated storage and retrieval systems (AS/RS)
become frequently used systems in warehouses. There has been a
transition from human based forklift applications to fast and safe
AS/RS applications in firm-s warehouse systems. In this study, basic
components and automation systems of the AS/RS are examined.
Proposed system's automation components and their tasks in the
system control algorithm were stated. According to this control
algorithm the control system structure was obtained.
Abstract: This paper presents a Reliability-Based Topology
Optimization (RBTO) based on Evolutionary Structural Optimization
(ESO). An actual design involves uncertain conditions such as
material property, operational load and dimensional variation.
Deterministic Topology Optimization (DTO) is obtained without
considering of the uncertainties related to the uncertainty parameters.
However, RBTO involves evaluation of probabilistic constraints,
which can be done in two different ways, the reliability index
approach (RIA) and the performance measure approach (PMA). Limit
state function is approximated using Monte Carlo Simulation and
Central Composite Design for reliability analysis. ESO, one of the
topology optimization techniques, is adopted for topology
optimization. Numerical examples are presented to compare the DTO
with RBTO.
Abstract: This study describes a micro device integrated with
multi-chamber for polymerase chain reaction (PCR) with different
annealing temperatures. The device consists of the reaction
polydimethylsiloxane (PDMS) chip, a cover glass chip, and is
equipped with cartridge heaters, fans, and thermocouples for
temperature control. In this prototype, commercial software is utilized
to determine the geometric and operational parameters those are
responsible for creating the denaturation, annealing, and extension
temperatures within the chip. Two cartridge heaters are placed at two
sides of the chip and maintained at two different temperatures to
achieve a thermal gradient on the chip during the annealing step. The
temperatures on the chip surface are measured via an infrared imager.
Some thermocouples inserted into the reaction chambers are used to
obtain the transient temperature profiles of the reaction chambers
during several thermal cycles. The experimental temperatures
compared to the simulated results show a similar trend. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: In this paper, the bio-mechanical analysis of human joints is carried out and the study is extended to the robot manipulator. This study will first focus on the kinematics of human arm which include the movement of each joint in shoulder, wrist, elbow and finger complexes. Those analyses are then extended to the design of a human robot manipulator. A simulator is built for Direct Kinematics and Inverse Kinematics of human arm. In the simulation of Direct Kinematics, the human joint angles can be inserted, while the position and orientation of each finger tips (end-effector) are shown. Inverse Kinematics does the reverse of the Direct Kinematics. Based on previous materials obtained from kinematics analysis, the human manipulator joints can be designed to follow prescribed position trajectories.
Abstract: Experimental investigations were made on the instability of supercritical kerosene flowing in active cooling channels. Two approaches were used to control the pressure in the channel. One is the back-pressure valve while the other is the venturi. In both conditions, a kind of low-frequency oscillation of pressure and temperature is observed. And the oscillation periods are calculated. By comparison with the flow time, it is concluded that the instability occurred in active cooling channels is probably one kind of density wave instability. And its period has no relationship with the cooling channel geometry, nor the pressure, but only depends on the flow time of kerosene in active cooling channels. When the mass flow rate, density and pressure drop couple with each other, the density wave instability will appear.