Abstract: The primary objective of this research is to improve the flexural capacity of FRP strengthened RC Beam structures with Aluminum and Titanium laminates. FRP rupture of flexural strengthened RC beams using FRP plates generally occurs at the interface between FRP plate and the beam. Therefore, in order to prevent brittle rupture and improve the ductility of the system, this research was performed by using Aluminum and Titanium materials between the two different structural systems. The research also aims to provide various strengthening/retrofitting methods for RC beam structures and to conduct a preliminary analysis of the demands on the structural systems. This was achieved by estimation using the experimental data from this research to identify a flexural capacity for the systems. Ultimately, the preliminary analysis of current study showed that the flexural capacity and system demand ductility was significantly improved by the systems inserted with Aluminum and Titanium anchor plates. Further verification of the experimental research is currently on its way to develop a new or reliable design guideline to retrofit/strengthen the concrete-FRP structural system can be evaluated.
Abstract: This paper presents an iterative algorithm to find a
inverse kinematic solution of 5-DOF robot. The algorithm is to
minimize the iteration number. Since the 5-DOF robot cannot give full
orientation of tool. Only z-direction of tool is satisfied while rotation
of tool is determined by kinematic constraint. This work therefore
described how to specify the tool direction and let the tool rotation free.
The simulation results show that this algorithm effectively worked.
Using the proposed iteration algorithm, error due to inverse kinematics
converged to zero rapidly in 5 iterations. This algorithm was applied in
real welding robot and verified through various practical works.
Abstract: In manufacturing industries, development of measurement leads to increase the number of monitoring variables and eventually the importance of multivariate control comes to the fore. Statistical process control (SPC) is one of the most widely used as multivariate control chart. Nevertheless, SPC is restricted to apply in processes because its assumption of data as following specific distribution. Unfortunately, process data are composed by the mixture of several processes and it is hard to estimate as one certain distribution. To alternative conventional SPC, therefore, nonparametric control chart come into the picture because of the strength of nonparametric control chart, the absence of parameter estimation. SVDD based control chart is one of the nonparametric control charts having the advantage of flexible control boundary. However,basic concept of SVDD has been an oversight to the important of data characteristic, density distribution. Therefore, we proposed DW-SVDD (Density Weighted SVDD) to cover up the weakness of conventional SVDD. DW-SVDD makes a new attempt to consider dense of data as introducing the notion of density Weight. We extend as control chart using new proposed SVDD and a simulation study of various distributional data is conducted to demonstrate the improvement of performance.
Abstract: E-learning is not restricted to the use of new technologies for the online content, but also induces the adoption of new approaches to improve the quality of education. This quality depends on the ability of these approaches (technical and pedagogical) to provide an adaptive learning environment. Thus, the environment should include features that convey intentions and meeting the educational needs of learners by providing a customized learning path to acquiring a competency concerned In our proposal, we believe that an individualized learning path requires knowledge of the learner. Therefore, it must pass through a personalization of diagnosis to identify precisely the competency gaps to fill, and reduce the cognitive load To personalize the diagnosis and pertinently measure the competency gap, we suggest implementing the formative assessment in the e-learning environment and we propose the introduction of a pre-regulation process in the area of formative assessment, involving its individualization and implementation in e-learning.
Abstract: Since the 1990s the American furniture industry faces a transition period. Manufacturers, one of its most important actors made its entrance into the retail industry. This shift has had deep consequences not only for the American furniture industry as a whole, but also for other international furniture industries, especially the Chinese. The present work aims to analyze this actor based on the distinction provided by the Global Commodity Chain Theory. It stresses its characteristics, structure, operational way and importance for both the U.S. and the Chinese furniture industries.
Abstract: This study proposes a novel recommender system to
provide the advertisements of context-aware services. Our proposed
model is designed to apply a modified collaborative filtering (CF)
algorithm with regard to the several dimensions for the personalization
of mobile devices – location, time and the user-s needs type. In
particular, we employ a classification rule to understand user-s needs
type using a decision tree algorithm. In addition, we collect primary
data from the mobile phone users and apply them to the proposed
model to validate its effectiveness. Experimental results show that the
proposed system makes more accurate and satisfactory advertisements
than comparative systems.
Abstract: The essentiality of maintenance assessment and
maintenance optimization in design stage is analyzed, and the existent
problems of conventional maintenance design method are illuminated.
MDMVM (Maintenance Design Method based Virtual Maintenance)
is illuminated, and the process of MDMVM established, and the
MDMVM architecture is given out. The key techniques of MDMVM
are analyzed, and include maintenance design based KBE (Knowledge
Based Engineering) and virtual maintenance based physically
attribute. According to physical property, physically based modeling,
visual object movement control, the simulation of operation force and
maintenance sequence planning method are emphatically illuminated.
Maintenance design system based virtual maintenance is established in
foundation of maintenance design method.
Abstract: Modeling of a manufacturing system enables one to
identify the effects of key design parameters on the system performance and as a result to make correct decision. This paper
proposes a manufacturing system modeling approach using a spreadsheet model based on queuing network theory, in which a
static capacity planning model and stochastic queuing model are integrated. The model was used to improve the existing system utilization in relation to product design. The model incorporates few
parameters such as utilization, cycle time, throughput, and batch size.
The study also showed that the validity of developed model is good enough to apply and the maximum value of relative error is 10%, far
below the limit value 32%. Therefore, the model developed in this
study is a valuable alternative model in evaluating a manufacturing system
Abstract: Virtual Assembly (VA) is one of the key technologies
in advanced manufacturing field. It is a promising application of
virtual reality in design and manufacturing field. It has drawn much
interest from industries and research institutes in the last two decades.
This paper describes a process for integrating an interactive Virtual
Reality-based assembly simulation of a digital mockup with the
CAD/CAM infrastructure. The necessary hardware and software
preconditions for the process are explained so that it can easily be
adopted by non VR experts. The article outlines how assembly
simulation can improve the CAD/CAM procedures and structures;
how CAD model preparations have to be carried out and which
virtual environment requirements have to be fulfilled. The issue of
data transfer is also explained in the paper. The other challenges and
requirements like anti-aliasing and collision detection have also been
explained. Finally, a VA simulation has been carried out for a ball
valve assembly and a car door assembly with the help of Vizard
virtual reality toolkit in a semi-immersive environment and their
performance analysis has been done on different workstations to
evaluate the importance of graphical processing unit (GPU) in the
field of VA.
Abstract: The present paper discusses the basic concepts and the underlying principles of Multi-Agent Systems (MAS) along with an interdisciplinary exploitation of these principles. It has been found that they have been utilized for lots of research and studies on various systems spanning across diverse engineering and scientific realms showing the need of development of a proper generalized framework. Such framework has been developed for the Multi-Agent Systems and it has been generalized keeping in mind the diverse areas where they find application. All the related aspects have been categorized and a general definition has been given where ever possible.
Abstract: Injection forging is a Nett-shape manufacturing
process in which one or two punches move axially causing a radial
flow into a die cavity in a form which is prescribed by the exitgeometry,
such as pulley, flanges, gears and splines on a shaft. This
paper presents an experimental and numerical study of the injection
forging of splines in terms of load requirement and material flow.
Three dimensional finite element analyses are used to investigate the
effect of some important parameters in this process. The experiment
has been carried out using solid commercial lead billets with two
different billet diameters and four different dies.
Abstract: As in today's semiconductor industries test costs can make up to 50 percent of the total production costs, an efficient test error detection becomes more and more important. In this paper, we present a new machine learning approach to test error detection that should provide a faster recognition of test system faults as well as an improved test error recall. The key idea is to learn a classifier ensemble, detecting typical test error patterns in wafer test results immediately after finishing these tests. Since test error detection has not yet been discussed in the machine learning community, we define central problem-relevant terms and provide an analysis of important domain properties. Finally, we present comparative studies reflecting the failure detection performance of three individual classifiers and three ensemble methods based upon them. As base classifiers we chose a decision tree learner, a support vector machine and a Bayesian network, while the compared ensemble methods were simple and weighted majority vote as well as stacking. For the evaluation, we used cross validation and a specially designed practical simulation. By implementing our approach in a semiconductor test department for the observation of two products, we proofed its practical applicability.
Abstract: In this paper we propose an NLP-based method for
Ontology Population from texts and apply it to semi automatic
instantiate a Generic Knowledge Base (Generic Domain Ontology) in
the risk management domain. The approach is semi-automatic and
uses a domain expert intervention for validation. The proposed
approach relies on a set of Instances Recognition Rules based on
syntactic structures, and on the predicative power of verbs in the
instantiation process. It is not domain dependent since it heavily
relies on linguistic knowledge.
A description of an experiment performed on a part of the
ontology of the PRIMA1 project (supported by the European
community) is given. A first validation of the method is done by
populating this ontology with Chemical Fact Sheets from
Environmental Protection Agency2. The results of this experiment
complete the paper and support the hypothesis that relying on the
predicative power of verbs in the instantiation process improves the
performance.
Abstract: In the past decade, artificial neural networks (ANNs)
have been regarded as an instrument for problem-solving and
decision-making; indeed, they have already done with a substantial
efficiency and effectiveness improvement in industries and businesses.
In this paper, the Back-Propagation neural Networks (BPNs) will be
modulated to demonstrate the performance of the collaborative
forecasting (CF) function of a Collaborative Planning, Forecasting and
Replenishment (CPFR®) system. CPFR functions the balance between
the sufficient product supply and the necessary customer demand in a
Supply and Demand Chain (SDC). Several classical standard BPN will
be grouped, collaborated and exploited for the easy implementation of
the proposed modular ANN framework based on the topology of a
SDC. Each individual BPN is applied as a modular tool to perform the
task of forecasting SKUs (Stock-Keeping Units) levels that are
managed and supervised at a POS (point of sale), a wholesaler, and a
manufacturer in an SDC. The proposed modular BPN-based CF
system will be exemplified and experimentally verified using lots of
datasets of the simulated SDC. The experimental results showed that a
complex CF problem can be divided into a group of simpler
sub-problems based on the single independent trading partners
distributed over SDC, and its SKU forecasting accuracy was satisfied
when the system forecasted values compared to the original simulated
SDC data. The primary task of implementing an autonomous CF
involves the study of supervised ANN learning methodology which
aims at making “knowledgeable" decision for the best SKU sales plan
and stocks management.
Abstract: Not all types of mobile phone are successful in entering the market because some types of the mobile phone have a negative perception of user. Therefore, it is important to understand the influence of mobile phone's characteristics in the local user perception. This research investigates the influence of QWERTY mobile phone's forms in the perception of Indonesian user. First, some alternatives of mobile phone-s form are developed based on a certain number of mobile phone's models. At the second stage, some word pairs as design attributes of the mobile phone are chosen to represent the user perception of mobile phone. At the final stage, a survey is conducted to investigate the influence of the developed form alternatives to the user perception. Based on the research, users perceive mobile phone's form with curved top and straight bottom shapes and mobile phone's form with slider and antenna as the most negative form. Meanwhile, mobile phone's form with curved top and bottom shapes and mobile phone-s form without slider and antenna are perceived by the user as the most positive form.
Abstract: The present work analyses different parameters of pressure die casting to minimize the casting defects. Pressure diecasting is usually applied for casting of aluminium alloys. Good surface finish with required tolerances and dimensional accuracy can be achieved by optimization of controllable process parameters such as solidification time, molten temperature, filling time, injection pressure and plunger velocity. Moreover, by selection of optimum process parameters the pressure die casting defects such as porosity, insufficient spread of molten material, flash etc. are also minimized. Therefore, a pressure die casting component, carburetor housing of aluminium alloy (Al2Si2O5) has been considered. The effects of selected process parameters on casting defects and subsequent setting of parameters with the levels have been accomplished by Taguchi-s parameter design approach. The experiments have been performed as per the combination of levels of different process parameters suggested by L18 orthogonal array. Analyses of variance have been performed for mean and signal-to-noise ratio to estimate the percent contribution of different process parameters. Confidence interval has also been estimated for 95% consistency level and three conformational experiments have been performed to validate the optimum level of different parameters. Overall 2.352% reduction in defects has been observed with the help of suggested optimum process parameters.
Abstract: The manufacture of large-scale precision aerospace
components using CNC requires a highly effective maintenance
strategy to ensure that the required accuracy can be achieved over
many hours of production. This paper reviews a strategy for a
maintenance management system based on Failure Mode Avoidance,
which uses advanced techniques and technologies to underpin a
predictive maintenance strategy. It is shown how condition
monitoring (CM) is important to predict potential failures in high
precision machining facilities and achieve intelligent and integrated
maintenance management. There are two distinct ways in which CM
can be applied. One is to monitor key process parameters and
observe trends which may indicate a gradual deterioration of
accuracy in the product. The other is the use of CM techniques to
monitor high status machine parameters enables trends to be
observed which can be corrected before machine failure and
downtime occurs.
It is concluded that the key to developing a flexible and intelligent
maintenance framework in any precision manufacturing operation is
the ability to evaluate reliably and routinely machine tool condition
using condition monitoring techniques within a framework of Failure
Mode Avoidance.
Abstract: We have developed a distributed asynchronous Web
based training system. In order to improve the scalability and robustness
of this system, all contents and functions are realized on mobile
agents. These agents are distributed to computers, and they can use
a Peer to Peer network that modified Content-Addressable Network.
In the proposed system, only text data can be included in a exercise.
To make our proposed system more useful, the mechanism that it not
only adapts to multimedia data but also it doesn-t influence the user-s
learning even if the size of exercise becomes large is necessary.
Abstract: Product Lead Time (PLT) is the period of time from
receiving a customer's order to delivering the final product. PLT is an
indicator of the manufacturing controllability, efficiency and
performance. Due to the explosion in the rate of technological
innovations and the rapid changes in the nature of manufacturing
processes, manufacturing firms can bring the new products to market
quicker only if they can reduce their PLT and speed up the rate at
which they can design, plan, control, and manufacture. Although
there is a substantial body of research on manufacturing relating to
cost and quality issues, there is no much specific research conducted
in relation to the formulation of PLT, despite its significance and
importance. This paper analyzes and formulates PLT which can be
used as a guideline for achieving the shorter PLT. Further more this
paper identifies the causes of delay and factors that contributes to the
increased product lead-time.
Abstract: This work will provide a new perspective of exploring innovation thematic. It will reveal that radical and incremental innovations are complementary during the innovation life cycle and accomplished through distinct ways of developing new products. Each new product development process will be constructed according to the nature of each innovation and the state of the product development. This paper proposes the inclusion of the organizational function areas that influence new product's development on the new product development process.