Abstract: Since supply chains highly impact the financial
performance of companies, it is important to optimize and analyze
their Key Performance Indicators (KPI). The synergistic combination
of Particle Swarm Optimization (PSO) and Monte Carlo simulation is
applied to determine the optimal reorder point of warehouses in
supply chains. The goal of the optimization is the minimization of the
objective function calculated as the linear combination of holding and
order costs. The required values of service levels of the warehouses
represent non-linear constraints in the PSO. The results illustrate that
the developed stochastic simulator and optimization tool is flexible
enough to handle complex situations.
Abstract: In this research, effect of combustion reaction
mechanism on direct initiation of detonation has been studied
numerically. For this purpose, reaction mechanism has been
simulated by using a three-step chemical kinetics model. The reaction
scheme consists sequentially of a chain-initiation and chainbranching
step, followed by a temperature -independent chaintermination.
In a previous research, the effect of chain-branching on
the direct initiation of detonation is studied. In this research effect of
chain-initiation on direct initiation of detonation is investigated. For
the investigation, first a characteristic time (τ) for each step of
mechanism, which includes effect of different kinetics parameters, is
defined. Then the effect of characteristic time of chain-initiation (τI)
on critical initiation energy is studied. It is seen that increasing τI,
causes critical initiation energy to be increased. Drawing detonation's
shock pressure diagrams for different cases, shows that in small value
of τI , kinetics has more important effect on the behavior of the wave.
Abstract: In automatic manufacturing and assembling of mechanical, electrical and electronic parts one needs to reliably identify the position of components and to extract the information of these components. Data Matrix Codes (DMC) are established by these days in many areas of industrial manufacturing thanks to their concentration of information on small spaces. In today’s usually order-related industry, where increased tracing requirements prevail, they offer further advantages over other identification systems. This underlines in an impressive way the necessity of a robust code reading system for detecting DMC on the components in factories. This paper compares two methods for estimating the angle of orientation of Data Matrix Codes: one method based on the Hough Transform and the other based on the Mean Shift Algorithm. We concentrate on Data Matrix Codes in industrial environment, punched, milled, lasered or etched on different materials in arbitrary orientation.
Abstract: The objective of this project is to produce computer
assisted instruction(CAI) for welding and brazing in order to
determine the efficiency of the instruction package and the study
accomplishment of learner by studying through computer assisted
instruction for welding and brazing it was examined through the
target group surveyed from the 30 students studying in the two year
of 5-year-academic program, department of production technology
education, faculty of industrial education and technology, king
mongkut-s university of technology thonburi. The result of the
research indicated that the media evaluated by experts and subject
matter quality evaluation of computer assisted instruction for welding
and brazing was in line for the good criterion. The mean of score
evaluated before the study, during the study and after the study was
34.58, 83.33 and 83.43, respectively. The efficiency of the lesson was
83.33/83.43 which was higher than the expected value, 80/80. The
study accomplishment of the learner, who utilizes computer assisted
instruction for welding and brazing as a media, was higher and equal
to the significance statistical level of 95%. The value was 1.669
which was equal to 35.36>1.669. It could be summarized that
computer assisted instruction for welding and brazing was the
efficient media to use for studying and teaching.
Abstract: The purpose of this study was to measure the maximal
isometric strength and to investigate the effects of different handleheights
and elbow angles with respect to Mid. sagittal plane on the
pushing and pulling strength in vertical direction. Eight male subjects
performed a series of static strength measurement for each subject.
The highest isometric strength was found in pulling at shoulder
height (S.H.) (Mean = 60.29 lb., SD = 16.78 lb.) and the lowest
isometric strength was found also in pulling at elbow height (E.H.)
(Mean = 33.06 lb., SD = 6.56 lb.). Although the isometric strengths
were higher at S.H than at E.H. for both activities, the maximal
isometric strengths were compared statistically. ANOVA was
performed. The results of the experiment revealed that there was a
significant different between handle heights. However, there were no
significant different between angles and activities, also no correlation
between grip strength and activities.
Abstract: In this document, we have proposed a robust
conceptual strategy, in order to improve the robustness against the manufacturing defects and thus the reliability of logic CMOS circuits. However, in order to enable the use of future CMOS
technology nodes this strategy combines various types of design:
DFR (Design for Reliability), techniques of tolerance: hardware
redundancy TMR (Triple Modular Redundancy) for hard error
tolerance, the DFT (Design for Testability. The Results on largest ISCAS and ITC benchmark circuits show that our approach improves
considerably the reliability, by reducing the key factors, the area costs and fault tolerance probability.
Abstract: Education, as the most important resource in any country, has multiplying effects on all facets of development in a society. The new social realities, particularly the interplay between democratization of education; unprecedented developments in IT sector; emergence of knowledge society, liberalization of economy and globalization have greatly influenced the educational process of all nations. This turbulence entails upon education to undergo dramatic changes to keep up with the new expectations. Growth of entrepreneurship among Indian women is highly important for empowering them and this is highly essential for socio-economic development of a society. Unfortunately in India there is poor acceptance of entrepreneurship among women as unfounded myths and fears restrain them to be enterprising. To remove these inhibitions, education system needs to be re-engineered to make entrepreneurship more acceptable. This paper empirically analyses the results of a survey done on around 500 female graduates in North India to measure and evaluate various entrepreneurial traits present in them. A formative model has been devised in this context, which should improve the teaching-learning process in our education system, which can lead to sustainable growth of women entrepreneurship in India.
Abstract: Among the numerous economic evaluation techniques currently available, Multi-criteria Spatial Analysis lends itself to solving localization problems of property complexes and, in particular, production plants. The methodology involves the use of Geographical Information Systems (GIS) and the mapping overlay technique, which overlaps the different information layers of a territory in order to obtain an overview of the parameters that characterize it. This first phase is used to detect possible settlement surfaces of a new agglomeration, subsequently selected through Analytic Hierarchy Process (AHP), so as to choose the best alternative. The result ensures the synthesis of a multidimensional profile that expresses both the quantitative and qualitative effects. Each criterion can be given a different weight.
Abstract: A water reuse system in wetland paddy was simulated
to supply water for industrial in this paper. A two-tank model was employed to represent the return flow of the wetland paddy.Historical data were performed for parameter estimation and model verification. With parameters estimated from the data, the model was then used to simulate a reasonable return flow rate from the wetland
paddy. The simulation results show that the return flow ratio was 11.56% in the first crop season and 35.66% in the second crop
season individually; the difference may result from the heavy rainfall in the second crop season. Under the existent pond with surplus
active capacity, the water reuse ratio was 17.14%, and the water supplementary ratio was 21.56%. However, the pattern of rainfall, the
active capacity of the pond, and the rate of water treatment limit the
volume of reuse water. Increasing the irrigation water, dredging the
depth of pond before rainy season and enlarging the scale of module are help to develop water reuse system to support for the industrial
water use around wetland paddy.
Abstract: We consider a single-echelon, single-item inventory
system where both demand and lead-time are stochastic. Continuous
review policy is used to control the inventory system. The objective
is to calculate the reorder point level under stochastic parameters. A
case study is presented in Neonatal Intensive Care Unit.
Abstract: This paper presents findings from the evaluation study carried out to review the UAE national ID card software. The paper consults the relevant literature to explain many of the concepts and frameworks explained herein. The findings of the evaluation work that was primarily based on the ISO 9126 standard for system quality measurement highlighted many practical areas that if taken into account is argued to more likely increase the success chances of similar system implementation projects.
Abstract: Research and development R&D work involves
enormous amount of work that has to do with data measurement and
collection. This process evolves as new information is fed, new
technologies are utilized, and eventually new knowledge is created
by the stakeholders i.e., researchers, clients, and end-users. When
new knowledge is created, procedures of R&D work should evolve
and produce better results within improved research skills and
improved methods of data measurements and collection. This
measurement improvement should then be benchmarked against a
metric that should be developed at the organization. In this paper, we
are suggesting a conceptual metric for R&D work performance
improvement (PI) at the Kuwait Institute for Scientific Research
(KISR). This PI is to be measured against a set of variables in the
suggested metric, which are more closely correlated to organizational
output, as opposed to organizational norms. The paper also mentions
and discusses knowledge creation and management as an addedvalue
to R&D work and measurement improvement. The research
methodology followed in this work is qualitative in nature, based on
a survey that was distributed to researchers and interviews held with
senior researchers at KISR. Research and analyses in this paper also
include looking at and analyzing KISR-s literature.
Abstract: This research presents a fuzzy multi-objective model
for a machine selection problem in a flexible manufacturing system
of a tire company. Two main objectives are minimization of an
average machine error and minimization of the total setup time.
Conventionally, the working team uses trial and error in selecting a
pressing machine for each task due to the complexity and constraints
of the problem. So, both objectives may not satisfy. Moreover, trial
and error takes a lot of time to get the final decision. Therefore, in
this research preemptive fuzzy goal programming model is developed
for solving this multi-objective problem. The proposed model can
obtain the appropriate results that the Decision Making (DM) is
satisfied for both objectives. Besides, alternative choice can be easily
generated by varying the satisfaction level. Additionally, decision
time can be reduced by using the model, which includes all
constraints of the system to generate the solutions. A numerical
example is also illustrated to show the effectiveness of the proposed
model.
Abstract: Traditionally, project scheduling and material planning have been treated independently. In this research, a mixed integer programming model is presented to integrate project scheduling and materials ordering problems. The goal is to minimize the total material holding and ordering costs. In addition, an efficient metaheuristic algorithm is proposed to solve the model. The proposed algorithm is computationally tested, the results are analyzed, and conclusions are given.
Abstract: The analysis is mainly concentrating on the knowledge
management literatures productivity trend which subjects as
“knowledge management" in SSCI database. The purpose what the
analysis will propose is to summarize the trend information for
knowledge management researchers since core knowledge will be
concentrated in core categories. The result indicated that the literature
productivity which topic as “knowledge management" is still
increasing extremely and will demonstrate the trend by different
categories including author, country/territory, institution name,
document type, language, publication year, and subject area. Focus on
the right categories, you will catch the core research information. This
implies that the phenomenon "success breeds success" is more
common in higher quality publications.
Abstract: In production planning (PP) periods with excess capacity
and growing demand, the manufacturers have two options to use the excess capacity. First, it could do more changeovers and thus reduce lot sizes, inventories, and inventory costs. Second, it could produce in excess of demand in the period and build additional inventory that can be used to satisfy future demand increments, thus
delaying the purchase of the next machine that is required to meet the growth in demand. In this study we propose an enhanced supply
chain planning model with flexible planning capability. In addition, a 3D supply chain planning system is illustrated.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: Nowadays there are more than thirty maturity models
in different knowledge areas. Maturity model is an area of interest
that contributes organizations to find out where they are in a specific
knowledge area and how to improve it. As Information Resource
Management (IRM) is the concept that information is a major
corporate resource and must be managed using the same basic
principles used to manage other assets, assessment of the current
IRM status and reveal the improvement points can play a critical role
in developing an appropriate information structure in organizations.
In this paper we proposed a framework for information resource
management maturity model (IRM3) that includes ten best practices
for the maturity assessment of the organizations' IRM.
Abstract: Modeling product configurations needs large amounts of knowledge about technical and marketing restrictions on the product. Previous attempts to automate product configurations concentrate on representations and management of the knowledge for specific domains in fixed and isolated computing environments. Since the knowledge about product configurations is subject to continuous change and hard to express, these attempts often failed to efficiently manage and exchange the knowledge in collaborative product development. In this paper, XML Topic Map (XTM) is introduced to represent and exchange the knowledge about product configurations in collaborative product development. A product configuration model based on XTM along with its merger and inference facilities enables configuration engineers in collaborative product development to manage and exchange their knowledge efficiently. A prototype implementation is also presented to demonstrate the proposed model can be applied to engineering information systems to exchange the product configuration knowledge.
Abstract: The Integrated Management of Child illnesses (IMCI) and the surveillance Health Information Systems (HIS) are related strategies that are designed to manage child illnesses and community practices of diseases. However, both strategies do not function well together because of classification incompatibilities and, as such, are difficult to use by health care personnel in rural areas where a majority of people lack the basic knowledge of interpreting disease classification from these methods. This paper discusses a single approach on how a stand-alone expert system can be used as a prompt diagnostic tool for all cases of illnesses presented. The system combines the action-oriented IMCI and the disease-oriented HIS approaches to diagnose malaria and typhoid fever in the rural areas of the Niger-delta region.