Abstract: In this work, new experimental data for slugging
frequency in inclined gas-liquid flow are reported, and a new
correlation is proposed. Scale experiments were carried out using a
mixture of air and water in a 6 m long pipe. Two different pipe
diameters were used, namely, 38 and 67 mm. The data were taken
with capacitance type sensors at a data acquisition frequency of 200
Hz over an interval of 60 seconds. For the range of flow conditions
studied, the liquid superficial velocity is observed to influence the
frequency strongly. A comparison of the present data with
correlations available in the literature reveals a lack of agreement. A
new correlation for slug frequency has been proposed for the inclined
flow, which represents the main contribution of this work.
Abstract: The direct synthesis process of dimethyl ether (DME)
from syngas in slurry reactors is considered to be promising because
of its advantages in caloric transfer. In this paper, the influences of
operating conditions (temperature, pressure and weight hourly space
velocity) on the conversion of CO, selectivity of DME and methanol
were studied in a stirred autoclave over Cu-Zn-Al-Zr slurry catalyst,
which is far more suitable to liquid phase dimethyl ether synthesis
process than bifunctional catalyst commercially. A Langmuir-
Hinshelwood mechanism type global kinetics model for liquid phase
DME direct synthesis based on methanol synthesis models and a
methanol dehydration model has been investigated by fitting our
experimental data. The model parameters were estimated with
MATLAB program based on general Genetic Algorithms and
Levenberg-Marquardt method, which is suitably fitting experimental
data and its reliability was verified by statistical test and residual
error analysis.
Abstract: Hypericum perforatum L. is a member of the Hypericaceae (Guttiferae) family and commonly known as St. John’s wort. There is a growing interest in this medicinal plant because of the constituents of this genus. A number of species have been shown to possess various biological activities such as antiviral, wound healing, analgesic, hepatoprotective, antimicrobial and antioxidant activities and also have therapeutic effects on burns, bruises, swelling, anxiety and mild to moderate depression.
In this study, the aerial parts of Hypericum perforatum L. are extracted and the main and effective constituents are determined. The analysis of the extracts was performed by GC-MS and LC-MS. As a next step, it is aimed to investigate the usage of the main constituents of the medicinal plant.
Abstract: Spatial understanding and the understanding of
dynamic change in the spatial structure of molecules during a
reaction is essential for designing new molecules. Knowing the
physical processes in the reactions helps to speed up the designing
process. To support the designer with the correct representation of
the designed molecule as well as showing the dynamic behavior of
the whole reacting system is the goal of our application. Our system
shows the spatial deformation of the molecules at every time interval
by minimizing the energy level of the molecules. The position and
orientation of the molecules can be intuitively controlled by
manipulating objects of the real world using Augmented Reality
techniques. Our approach has the potential to speed up the design of
new molecules and help students to understand the chemical
processes better.
Abstract: In this study the extracts of the Iraqi herb Tribulus
terrestris (Al-Hassage or Al-Kutub) was done by using of polar and
non polar solvents, then the biological activity of these extractants
was studied in three fields, First, the antibacterial activity (in vitro)
on gram positive bacteria (Staphylococcus aureus), and gram
negative bacteria (E. coli, Proteus vulgaris, Pseudomonas
aerugiuosa, and Klebsiella), all extracts showed considerable activity
against all bacteria. Second, the effect of extracts on free serum
testosterone level in male mice (in vivo), the alcoholic, and
acetonitrilic extracts showed significant (P < 0.05) increase in free
serum testosterone level, and we found that the extracts contained
compounds with less genotoxic effects in mice germ cells. 3rd, was to
study the effect of methanolic extract of T. terrestris in diabetes
management.
Abstract: Using ab initio theoretical calculations, we present
analysis of fragmentation process. The analysis is performed in two
steps. The first step is calculation of fragmentation energies by ab
initio calculations. The second step is application of the energies to
kinetic description of process. The energies of fragments are
presented in this paper. The kinetics of fragmentation process can be
described by numerical models. The method for kinetic analysis is
described in this paper. The result - composition of fragmentation
products - will be calculated in future. The results from model can be
compared to the concentrations of fragments from mass spectrum.
Abstract: Proton transfer and hydrogen bonding are two aspects
of the chemistry of hydrogen that respectively govern the behaviour
and structure of many molecules, both simple and complex. All the
theoretical enol and keto conformations of 1,3-diphenyl-1,3-
propandion known as dibenzoylmethane (DBM), have been
investigated by means of atoms in molecules (AIM) theory. It was
found that the most stable conformers are those stabilized by
hydrogen bridges.The aim of the present paper is a thorough
conformational analysis of DBM (with special attention on chelated
cis-enol conformers) in order to obtain detailed information on the
geometrical parameters, relative stabilities and rotational motion of
the phenyl groups. It is also important to estimate the barrier height
for ptoton transfer and hydrogen bond strength, which are the main
factors governing conformational stability.
Abstract: Because of the requirement for low sulfur content of
fuel oils, it is necessary to develop alternative methods for desulfurization of heavy fuel oil. Due to the disadvantages of HDS
technologies such as costs, safety and green environment, new
methods have been developed. Among these methods is ultrasoundassisted
oxidative desulfurization. Using ultrasound-assisted
oxidative desulfurization, compounds such as benzothiophene and
dibenzothiophene can be oxidized. As an alternative method is sulfur
elimination of heavy fuel oil by using of activated carbon in a packed column in batch condition. The removal of sulfur compounds in this
case to reach about 99%. The most important property of activated carbon is ability of it for adsorption, which is due to high surface area
and pore volume of it.
Abstract: This work concerns on experimentally investigation
of surfactant flooding in fractured porous media. In this study a series
of water and surfactant injection processes were performed on
micromodels initially saturated with a heavy crude oil. Eight
fractured glass micromodels were used to illustrate effects of
surfactant types and concentrations on oil recovery efficiency in
presence of fractures with different properties i.e. fracture
orientation, length and number of fractures. Two different
surfactants with different concentrations were tested. The results
showed that surfactant flooding would be more efficient by using
SDS surfactant aqueous solution and also by locating injection well
in a proper position respect to fracture properties. This study
demonstrates different physical and chemical conditions that affect
the efficiency of this method of enhanced oil recovery.
Abstract: Dissolved gas analysis has been accepted as a sensitive, informative and reliable technique for incipient faults detection in power transformers and is widely used. In the last few years this method, which has been recommended by IEEE Power & Energy society, has been applied for fault detection in load tap changers. Regarding the critical role of load tap changers in electrical network and essential of catastrophic failures prevention, it is necessary to choose "condition based preventative maintenance strategy" which leads to reduction in costs, the number of unnecessary visits as well as the probability of interruptions and also increment in equipment reliability. In current work, considering the condition based preventative maintenance strategy, condition assessment of an Elin tap changer was carried out using dissolved gas analysis.
Abstract: Adsorption of proteins onto a solid surface is believed to be the initial and controlling step in biofouling. A better knowledge of the fouling process can be obtained by controlling the formation of the first protein layer at a solid surface. A number of methods have been investigated to inhibit adsorption of proteins. In this study, the adsorption kinetics of
Abstract: Mycophenolic acid (MPA) is a secondary metabolite
produced by Penicillium brevicompactum, which has antibiotic and
immunosuppressive properties. In this study, the first, mycophenolic
acid was produced in a fermentation process by Penicillium
brevicompactum MUCL 19011 in shake flask using a base medium.
The maximum MPA production, product yield and productivity of
process were 1.379 g/L, 18.6 mg/g glucose and 4.9 mg/L. h,
respectively. Also the glucose consumption, biomass and MPA
production profiles were investigated during batch cultivation.
Obtained results showed that MPA production starts approximately
after 180 hours and reaches to a maximum at 280 h. In the next step,
the effects of some various concentrations of enzymatically
hydrolyzed casein on MPA production were evaluated. Maximum
MPA production, product yield and productivity as 3.63 g/L, 49
mg/g glucose and 12.96 mg/L.h, respectively were obtained with
using 30 g/L enzymatically hydrolyzed casein in culture medium.
These values show an enhanced MPA production, product yield and
process productivity pr as 116.8%, 132.8% and 163.2%, respectively.
Abstract: In the present study, computational fluid dynamics
(CFD) simulation has been executed to investigate the transition
boundaries of different flow patterns for moderately viscous oil-water
(viscosity ratio 107, density ratio 0.89 and interfacial tension of 0.032
N/m.) two-phase flow through a horizontal pipeline with internal
diameter and length of 0.025 m and 7.16 m respectively. Volume of
Fluid (VOF) approach including effect of surface tension has been
employed to predict the flow pattern. Geometry and meshing of the
present problem has been drawn using GAMBIT and ANSYS
FLUENT has been used for simulation. A total of 47037 quadrilateral
elements are chosen for the geometry of horizontal pipeline. The
computation has been performed by assuming unsteady flow,
immiscible liquid pair, constant liquid properties, co-axial flow and a
T-junction as entry section. The simulation correctly predicts the
transition boundaries of wavy stratified to stratified mixed flow.
Other transition boundaries are yet to be simulated. Simulated data
has been validated with our own experimental results.
Abstract: This work presents a theoretical investigation of the
simultaneous absorption of CO2 and H2S into aqueous solutions of
MDEA and DEA. In this process the acid components react
with the basic alkanolamine solution via an exothermic,
reversible reaction in a gas/liquid absorber. The use of amine
solvents for gas sweetening has been investigated using
process simulation programs called HYSYS and ASPEN. We
use Electrolyte NRTL and Amine Package and Amines
(experimental) equation of state. The effects of temperature and
circulation rate and amine concentration and packed column and
murphree efficiency on the rate of absorption were studied.
When lean amine flow and concentration increase, CO2 and H2S
absorption increase too. With the improvement of inlet amine
temperature in absorber, CO2 and H2S penetrate to upper stages of
absorber and absorption of acid gases in absorber decreases. The CO2
concentration in the clean gas can be greatly influenced by the
packing height, whereas for the H2S concentration in the clean gas the
packing height plays a minor role. HYSYS software can not
estimate murphree efficiency correctly and it applies the same
contributions in all diagrams for HYSYS software. By
improvement in murphree efficiency, maximum temperature
of absorber decrease and the location of reaction transfer to the
stages of bottoms absorber and the absorption of acid gases
increase.
Abstract: Pure phase gallosilicate nitrite sodalite has been synthesized in a single step by low temperature (373 oK) hydrothermal technique. The product obtained was characterized using a combination of techniques including X-ray powder diffraction, IR, Raman spectroscopy, SEM, MAS NMR spectroscopy as well as thermogravimetry. Sodalite with an ideal composition was obtained after synthesis at 3730K and seven days duration using alkaline medium. The structural features of the Na8[GaSiO4]6(NO2)2 sodalite were investigated by IR, MAS NMR spectroscopy of 29Si and 23Na nuclei and by Reitveld refinement of X-ray powder diffraction data. The crystal structure of this sodalite has been refined in the space group P 4 3n; with a cell parameter 8.98386Å, V= 726.9 Å, (Rwp= 0.077 and Rp=0.0537) and Si-O-Ga angle is found to be 132.920 . MAS NMR study confirms complete ordering of Si and Ga in the gallosilicate framework. The surface area of single entity with stoichiometry Na8[GaSiO4]6(NO2)2 was found to be 8.083 x10-15 cm2/g.
Abstract: This article is presented an experimental and modeling
study of a four-bed pressure swing adsorption process using
zeolite13X to provide oxygen-enriched air. The binary mixture N2/O2
(79/21 vol %) was used as a feed stream. The effects of purge/feed
ratio (P/F), adsorption pressure, cyclic time and product flow rate on
product purity and recovery under nonisothermal condition were
studied. The adsorption dynamics of process were determined using
a mathematical model incorporated mass and energy balances. A
Mathlab code using finite difference method was developed to solve
the set of coupled differential-algebraic equations, and the simulation
results are agreed well with experimental results.
Abstract: Under the variation of crude oil price and the impact of
greenhouse effect, it is urgent to find a potential alternative fuel.
Among these alternative fuels, non edible plant oils are the most
potential ones, because they don-t have the problem of food and
cropland competitions. Among the non-edible plant oils, Jatropha oil
is the most potential one. Jatropha oil is non-eatable oil and has good
oil quality and low temperature performance. It has potential to
become one of the most competitive biomass crude oils. The crude
plant oil will be blended with diesel fuel to be tested in a power
generator. The international collaboration between Taiwan and
Indonesia on the production of Jatropha in Indonesia will also be
presented in this study.
Abstract: The equilibrium process of plasma nitrogen species by
chemical kinetic reactions along various pressures is successfully
investigated. The equilibrium process is required in industrial
application to obtain the stable condition when heating up the
material for having homogenous reaction. Nitrogen species densities
is modeled by a continuity equation and extended Arrhenius form.
These equations are used to integrate the change of density over the
time. The integration is to acquire density and the reaction rate of
each reaction where temperature and time dependence are imposed.
A comparison is made with global model within pressure range of 1-
100mTorr and the temperature of electron is set to be higher than
other nitrogen species. The results shows that the chemical kinetic
model only agrees for high pressure because of no power imposed;
while the global model considers the external power along the
pressure range then the electron and nitrogen species give highly
quantity densities by factor of 3 to 5.
Abstract: This article reports on the studies of porous GaN prepared by ultra-violet (UV) assisted electrochemical etching in a solution of 4:1:1 HF: CH3OH:H2O2 under illumination of an UV lamp with 500 W power for 10, 25 and 35 minutes. The optical properties of porous GaN sample were compared to the corresponding as grown GaN. Porosity induced photoluminescence (PL) intensity enhancement was found in these samples. The resulting porous GaN displays blue shifted PL spectra compared to the as-grown GaN. Appearance of the blue shifted emission is correlated with the development of highly anisotropic structures in the morphology. An estimate of the size of the GaN nanostructure can be obtained with the help of a quantized state effective mass theory.
Abstract: Enzymatic hydrolysis is one of the major steps involved in the conversion from sugarcane bagasse to yield ethanol. This process offers potential for yields and selectivity higher, lower energy costs and milder operating conditions than chemical processes. However, the presence of some factors such as lignin content, crystallinity degree of the cellulose, and particle sizes, limits the digestibility of the cellulose present in the lignocellulosic biomasses. Pretreatment aims to improve the access of the enzyme to the substrate. In this study sugarcane bagasse was submitted chemical pretreatment that consisted of two consecutive steps, the first with dilute sulfuric acid (1 % (v/v) H2SO4), and the second with alkaline solutions with different concentrations of NaOH (1, 2, 3 and 4 % (w/v)). Thermal Analysis (TG/ DTG and DTA) was used to evaluate hemicellulose, cellulose and lignin contents in the samples. Scanning Electron Microscopy (SEM) was used to evaluate the morphological structures of the in natura and chemically treated samples. Results showed that pretreatments were effective in chemical degradation of lignocellulosic materials of the samples, and also was possible to observe the morphological changes occurring in the biomasses after pretreatments.