Abstract: A simple microstructure optical fiber design based on an octagonal cladding structure is presented for simultaneously controlling dispersion and leakage properties. The finite difference method with anisotropic perfectly matched boundary layer is used to investigate the guiding properties. It is demonstrated that octagonal photonic crystal fibers with four rings can assume negative ultra-flattened dispersion of -19 + 0.23 ps/nm/km in the wavelength range of 1.275 μm to 1.68 μm, nearly zero ultra-flattened dispersion of 0 ± 0.40 ps/nm/km in a 1.38 to 1.64 μm, and low confinement losses less than 10-3 dB/km in the entire band of interest.
Abstract: Regenerative gas turbine engine cycle is presented that yields higher cycle efficiencies than simple cycle operating under the same conditions. The power output, efficiency and specific fuel consumption are simulated with respect to operating conditions. The analytical formulae about the relation to determine the thermal efficiency are derived taking into account the effected operation conditions (ambient temperature, compression ratio, regenerator effectiveness, compressor efficiency, turbine efficiency and turbine inlet temperature). Model calculations for a wide range of parameters are presented, as are comparisons with simple gas turbine cycle. The power output and thermal efficiency are found to be increasing with the regenerative effectiveness, and the compressor and turbine efficiencies. The efficiency increased with increase the compression ratio to 5, then efficiency decreased with increased compression ratio, but in simple cycle the thermal efficiency always increase with increased in compression ratio. The increased in ambient temperature caused decreased thermal efficiency, but the increased in turbine inlet temperature increase thermal efficiency.
Abstract: There is a variety of inconsistencies in the differences
in alcohol use and related problems between male and female
genders. This study was aimed at analyzing the gender differences in
alcohol use and related problems among university students in
Minsk, Belarus. A total of 465 male (average age of 21) and 1030
female (average age of 20.5) students from four major universities in
Minsk, Belarus were administered WHO recommended standardized
screening instruments – AUDIT, MAST, CAGE questionnaire, as
well as other alcohol related questions. The male to female ratio for
the prevalence of alcohol problems according to the AUDIT was
3.34, while the ratio for alcohol users was 0.97. There are a wide
gender differences in the pattern of alcohol use and preference for
different alcoholic beverages, cause for drinking, and other alcohol
related problems like injuries and blackouts.
Abstract: Semiconductor nanomaterials like TiO2 nanoparticles
(TiO2-NPs) approximately less than 100 nm in diameter have become
a new generation of advanced materials due to their novel and
interesting optical, dielectric, and photo-catalytic properties. With the
increasing use of NPs in commerce, to date few studies have
investigated the toxicological and environmental effects of NPs.
Motivated by the importance of TiO2-NPs that may contribute to the
cancer research field especially from the treatment prospective
together with the fractal analysis technique, we have investigated the
effect of TiO2-NPs on colony morphology in the dark condition
using fractal dimension as a key morphological characterization
parameter. The aim of this work is mainly to investigate the cytotoxic
effects of TiO2-NPs in the dark on the growth of human cervical
carcinoma (HeLa) cell colonies from morphological aspect. The in
vitro studies were carried out together with the image processing
technique and fractal analysis. It was found that, these colonies were
abnormal in shape and size. Moreover, the size of the control
colonies appeared to be larger than those of the treated group. The
mean Df +/- SEM of the colonies in untreated cultures was
1.085±0.019, N= 25, while that of the cultures treated with TiO2-NPs
was 1.287±0.045. It was found that the circularity of the control
group (0.401±0.071) is higher than that of the treated group
(0.103±0.042). The same tendency was found in the diameter
parameters which are 1161.30±219.56 μm and 852.28±206.50 μm
for the control and treated group respectively. Possible explanation of
the results was discussed, though more works need to be done in
terms of the for mechanism aspects. Finally, our results indicate that
fractal dimension can serve as a useful feature, by itself or in
conjunction with other shape features, in the classification of cancer
colonies.
Abstract: Periphyton development and composition were
studied in three different treatments: (i) two fishpond units of
wetland-type wastewater treatment pond systems, (ii) two fishponds
in combined intensive-extensive fish farming systems and (iii) three
traditional polyculture fishponds. Results showed that amounts of
periphyton developed in traditional polyculture fishponds (iii) were
different compared to the other treatments (i and ii), where the main
function of ponds was stated wastewater treatment. Negative
correlation was also observable between water quality parameters
and periphyton production. The lower trophity, halobity and
saprobity level of ponds indicated higher amount of periphyton. The
dry matter content of periphyton was significantly higher in the
samples, which were developed in traditional polyculture fishponds
(2.84±3.02 g m-2 day-1, whereby the ash content in dry matter 74%),
than samples taken from (i) (1.60±2.32 g m-2 day-1, 61%) and (ii)
fishponds (0.65±0.45 g m-2 day-1, 81%).
Abstract: Zero inflated Strict Arcsine model is a newly developed model which is found to be appropriate in modeling overdispersed count data. In this study, maximum likelihood estimation method is used in estimating the parameters for zero inflated strict arcsine model. Bootstrapping is then employed to compute the confidence intervals for the estimated parameters.
Abstract: Service innovations are central concerns in fast
changing environment. Due to the fitness in customer demands and
advances in information technologies (IT) in service management, an
expanded conceptualization of e-service innovation is required.
Specially, innovation practices have become increasingly more
challenging, driving managers to employ a different open innovation
model to maintain competitive advantages. At the same time, firms
need to interact with external and internal customers in innovative
environments, like the open innovation networks, to co-create values.
Based on these issues, an important conceptual framework of e-service
innovation is developed. This paper aims to examine the contributing
factors on e-service innovation and firm performance, including
financial and non-financial aspects. The study concludes by showing
how e-service innovation will play a significant role in growing the
overall values of the firm. The discussion and conclusion will lead to a
stronger understanding of e-service innovation and co-creating values
with customers within open innovation networks.
Abstract: The recognition of human faces, especially those with
different orientations is a challenging and important problem in image
analysis and classification. This paper proposes an effective scheme
for rotation invariant face recognition using Log-Polar Transform and
Discrete Cosine Transform combined features. The rotation invariant
feature extraction for a given face image involves applying the logpolar
transform to eliminate the rotation effect and to produce a row
shifted log-polar image. The discrete cosine transform is then applied
to eliminate the row shift effect and to generate the low-dimensional
feature vector. A PSO-based feature selection algorithm is utilized to
search the feature vector space for the optimal feature subset.
Evolution is driven by a fitness function defined in terms of
maximizing the between-class separation (scatter index).
Experimental results, based on the ORL face database using testing
data sets for images with different orientations; show that the
proposed system outperforms other face recognition methods. The
overall recognition rate for the rotated test images being 97%,
demonstrating that the extracted feature vector is an effective rotation
invariant feature set with minimal set of selected features.
Abstract: This paper discusses the causal explanation capability
of QRIOM, a tool aimed at supporting learning of organic chemistry
reactions. The development of the tool is based on the hybrid use of
Qualitative Reasoning (QR) technique and Qualitative Process
Theory (QPT) ontology. Our simulation combines symbolic,
qualitative description of relations with quantity analysis to generate
causal graphs. The pedagogy embedded in the simulator is to both
simulate and explain organic reactions. Qualitative reasoning through
a causal chain will be presented to explain the overall changes made
on the substrate; from initial substrate until the production of final
outputs. Several uses of the QPT modeling constructs in supporting
behavioral and causal explanation during run-time will also be
demonstrated. Explaining organic reactions through causal graph
trace can help improve the reasoning ability of learners in that their
conceptual understanding of the subject is nurtured.
Abstract: Transpedicular screw fixation in spinal fractures,
degenerative changes, or deformities is a well-established procedure.
However, important rate of fixation failure due to screw bending,
loosening, or pullout are still reported particularly in weak bone stock
in osteoporosis. To overcome the problem, mechanism of failure has
to be fully investigated in vitro. Post-mortem human subjects are less
accessible and animal cadavers comprise limitations due to different
geometry and mechanical properties. Therefore, the development of a
synthetic model mimicking the realistic human vertebra is highly
demanded. A bone surrogate, composed of Polyurethane (PU) foam
analogous to cancellous bone porous structure, was tested for 3
different densities in this study. The mechanical properties were
investigated under uniaxial compression test by minimizing the end
artifacts on specimens. The results indicated that PU foam of 0.32
g.cm-3 density has comparable mechanical properties to human
cancellous bone in terms of young-s modulus and yield strength.
Therefore, the obtained information can be considered as primary
step for developing a realistic cancellous bone of human vertebral
body. Further evaluations are also recommended for other density
groups.
Abstract: In this paper a new approach to face recognition is presented that achieves double dimension reduction making the system computationally efficient with better recognition results. In pattern recognition techniques, discriminative information of image increases with increase in resolution to a certain extent, consequently face recognition results improve with increase in face image resolution and levels off when arriving at a certain resolution level. In the proposed model of face recognition, first image decimation algorithm is applied on face image for dimension reduction to a certain resolution level which provides best recognition results. Due to better computational speed and feature extraction potential of Discrete Cosine Transform (DCT) it is applied on face image. A subset of coefficients of DCT from low to mid frequencies that represent the face adequately and provides best recognition results is retained. A trade of between decimation factor, number of DCT coefficients retained and recognition rate with minimum computation is obtained. Preprocessing of the image is carried out to increase its robustness against variations in poses and illumination level. This new model has been tested on different databases which include ORL database, Yale database and a color database. The proposed technique has performed much better compared to other techniques. The significance of the model is two fold: (1) dimension reduction up to an effective and suitable face image resolution (2) appropriate DCT coefficients are retained to achieve best recognition results with varying image poses, intensity and illumination level.
Abstract: Experimental investigations were made on the instability of supercritical kerosene flowing in active cooling channels. Two approaches were used to control the pressure in the channel. One is the back-pressure valve while the other is the venturi. In both conditions, a kind of low-frequency oscillation of pressure and temperature is observed. And the oscillation periods are calculated. By comparison with the flow time, it is concluded that the instability occurred in active cooling channels is probably one kind of density wave instability. And its period has no relationship with the cooling channel geometry, nor the pressure, but only depends on the flow time of kerosene in active cooling channels. When the mass flow rate, density and pressure drop couple with each other, the density wave instability will appear.
Abstract: Titanium oxide films with different morphologies have for the first time been fabricated through hydrothermal reactions between a titanium substrate and iodine powder in water or ethanol. SEM revealed that iodine supported titanium (Ti-I2) surface shows different morphologies with variable treatment conditions. The mean surface roughness (Ra) was increased in the different groups. Use of surfactant has a role to increase the roughness of the film. The surface roughness was in the range of 0.15 μm-0.42 μm. Furthermore, the electrochemical examinations showed that the Ti-I2 surface fabricated in alcoholic medium has high corrosion resistance than in aqueous medium.
Abstract: A reduced order modeling approach for natural
gas transient flow in pipelines is presented. The Euler
equations are considered as the governing equations and
solved numerically using the implicit Steger-Warming flux
vector splitting method. Next, the linearized form of the
equations is derived and the corresponding eigensystem is
obtained. Then, a few dominant flow eigenmodes are used to
construct an efficient reduced-order model. A well-known test
case is presented to demonstrate the accuracy and the
computational efficiency of the proposed method. The results
obtained are in good agreement with those of the direct
numerical method and field data. Moreover, it is shown that
the present reduced-order model is more efficient than the
conventional numerical techniques for transient flow analysis
of natural gas in pipelines.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: The most common type of controller being used in
the industry is PI(D) controller which has been used since 1945 and
is still being widely used due to its efficiency and simplicity. In
most cases, the PI(D) controller was tuned without taking into
consideration of the effect of actuator saturation. In real processes,
the most common actuator which is valve will act as constraint and
restrict the controller output. Since the controller is not designed to
encounter saturation, the process may windup and consequently
resulted in large oscillation or may become unstable. Usually, an
antiwindup compensator is added to the feedback control loop to
reduce the deterioration effect of integral windup. This research
aims to specifically control processes with constraints. The
proposed method was applied to two different types of food
processes, which are blending and spray drying. Simulations were
done using MATLAB and the performances of the proposed
method were compared with other conventional methods. The
proposed technique was able to control the processes and avoid
saturation such that no anti windup compensator is needed.
Abstract: This experiment was performed with the purpose of
investigating effect of additional blend of probiotics Saccharomyces
cerevisiae and Lactobacillus acidophilus on plasma fatty acid profiles
particularly conjugated linoleic acid (CLA) in growing goats fed corn
silage, and selected the optimal levels of the probiotics for further study.
Twenty-four growing crossbred (Thai native x Anglo-Nubian) goats that
weighed (14.2 ± 2.3) kg, aged about 6 months, were purchased and
allocated to 4 treatments according to Randomized Complete Block
Design (RCBD) with 6 goats in each treatment. The blocks were made by
weight into heavy, medium, and light goats and each of the treatments
contained two goats from each of the blocks. In the mean time, ruminal
average pH unaffected, but the NH3-N and also plasma urea nitrogen
(p0.05) were raised, but propionic
proportion (p0.05) were reduced in
concurrent with raise of acetic proportion and resultantly C2:C3 ratio
(p>0.05). On plasma fatty acid profiles, total saturated fatty acids
(p>0.05) was increased, and contrasted with decrease of C15:0
(p0.05), and C18-C22 polyunsaturated fatty acids
(p
Abstract: Technological innovation capability (TIC) is
defined as a comprehensive set of characteristics of a firm that
facilities and supports its technological innovation strategies.
An audit to evaluate the TICs of a firm may trigger
improvement in its future practices. Such an audit can be used
by the firm for self assessment or third-party independent
assessment to identify problems of its capability status. This
paper attempts to develop such an auditing framework that
can help to determine the subtle links between innovation
capabilities and business performance; and to enable the
auditor to determine whether good practice is in place. The
seven TICs in this study include learning, R&D, resources
allocation, manufacturing, marketing, organization and
strategic planning capabilities. Empirical data was acquired
through a survey study of 200 manufacturing firms in the
Hong Kong/Pearl River Delta (HK/PRD) region. Structural
equation modelling was employed to examine the
relationships among TICs and various performance indicators:
sales performance, innovation performance, product
performance, and sales growth. The results revealed that
different TICs have different impacts on different
performance measures. Organization capability was found to
have the most influential impact. Hong Kong manufacturers
are now facing the challenge of high-mix-low-volume
customer orders. In order to cope with this change, good
capability in organizing different activities among various
departments is critical to the success of a company.
Abstract: Stock portfolio selection is a classic problem in finance,
and it involves deciding how to allocate an institution-s or an individual-s
wealth to a number of stocks, with certain investment objectives
(return and risk). In this paper, we adopt the classical Markowitz
mean-variance model and consider an additional common realistic
constraint, namely, the cardinality constraint. Thus, stock portfolio
optimization becomes a mixed-integer quadratic programming problem
and it is difficult to be solved by exact optimization algorithms.
Chemical Reaction Optimization (CRO), which mimics the molecular
interactions in a chemical reaction process, is a population-based
metaheuristic method. Two different types of CRO, named canonical
CRO and Super Molecule-based CRO (S-CRO), are proposed to solve
the stock portfolio selection problem. We test both canonical CRO
and S-CRO on a benchmark and compare their performance under
two criteria: Markowitz efficient frontier (Pareto frontier) and Sharpe
ratio. Computational experiments suggest that S-CRO is promising
in handling the stock portfolio optimization problem.
Abstract: A novel physico-chemical route to produce few layer graphene nanoribbons with atomically smooth edges is reported, via acid treatment (H2SO4:HNO3) followed by characteristic thermal shock processes involving extremely cold substances. Samples were studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman spectroscopy and X-ray photoelectron spectroscopy. This method demonstrates the importance of having the nanotubes open ended for an efficient uniform unzipping along the nanotube axis. The average dimensions of these nanoribbons are approximately ca. 210 nm wide and consist of few layers, as observed by transmission electron microscopy. The produced nanoribbons exhibit different chiralities, as observed by high resolution transmission electron microscopy. This method is able to provide graphene nanoribbons with atomically smooth edges which could be used in various applications including sensors, gas adsorption materials, composite fillers, among others.