Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: The present work was conducted for Arsenic (III)
removal, which one of the most poisonous groundwater pollutants, by
synthetic nano size zerovalent iron (nZVI). Batch experiments were
performed to investigate the influence of As (III), nZVI
concentration, pH of solution and contact time on the efficiency of As
(III) removal. nZVI was synthesized by reduction of ferric chloride
by sodium borohydrid. SEM and XRD were used to determine
particle size and characterization of produced nanoparticles. Up to
99.9% removal efficiency for arsenic (III) was obtained by nZVI
dosage of 1 g/L at time equal to 10 min. and pH=7. It could be
concluded that the removal efficiency were enhanced with increasing
of ZVI dosage and reaction time, but decreased with increasing of
arsenic concentration and pH for nano sized ZVI. nZVI presented an
outstanding ability to remove As (III) due to not only a high surface
area and low particle size but also to high inherent activity.
Abstract: This paper seeks to develop simple yet practical and
efficient control scheme that enables cooperating arms to handle a
flexible beam. Specifically the problem studied herein is that of two
arms rigidly grasping a flexible beam and such capable of generating
forces/moments in such away as to move a flexible beam along a
predefined trajectory. The paper develops a sliding mode control law
that provides robustness against model imperfection and uncertainty.
It also provides an implicit stability proof. Simulation results for two
three joint arms moving a flexible beam, are presented to validate the
theoretical results.
Abstract: The study of piezoelectric material in the past was in T-Domain form; however, no one has studied piezoelectric material in the S-Domain form. This paper will present the piezoelectric material in the transfer function or S-Domain model. S-Domain is a well known mathematical model, used for analyzing the stability of the material and determining the stability limits. By using S-Domain in testing stability of piezoelectric material, it will provide a new tool for the scientific world to study this material in various forms.
Abstract: Accurate loss minimization is the critical component
for efficient electrical distribution power flow .The contribution of
this work presents loss minimization in power distribution system
through feeder restructuring, incorporating DG and placement of
capacitor. The study of this work was conducted on IEEE
distribution network and India Electricity Board benchmark
distribution system. The executed experimental result of Indian
system is recommended to board and implement practically for
regulated stable output.
Abstract: This paper presents positive and negative full-wave
rectifier. The proposed structure is based on OTA using
commercially available ICs (LT1228). The features of the proposed
circuit are that: it can rectify and amplify voltage signal with
controllable output magnitude via input bias current: the output
voltage is free from temperature variation. The circuit description
merely consists of 1 single ended and 3 fully differential OTAs. The
performance of the proposed circuit are investigated though PSpice.
They show that the proposed circuit can function as positive/negative
full-wave rectifier, where the voltage input wide-dynamic range from
-5V to 5V. Furthermore, the output voltage is slightly dependent on
the temperature variations.
Abstract: This paper proposes a low power SRAM based on
five transistor SRAM cell. Proposed SRAM uses novel word-line
decoding such that, during read/write operation, only selected cell
connected to bit-line whereas, in conventional SRAM (CV-SRAM),
all cells in selected row connected to their bit-lines, which in turn
develops differential voltages across all bit-lines, and this makes
energy consumption on unselected bit-lines. In proposed SRAM
memory array divided into two halves and this causes data-line
capacitance to reduce. Also proposed SRAM uses one bit-line and
thus has lower bit-line leakage compared to CV-SRAM.
Furthermore, the proposed SRAM incurs no area overhead, and has
comparable read/write performance versus the CV-SRAM.
Simulation results in standard 0.25μm CMOS technology shows in
worst case proposed SRAM has 80% smaller dynamic energy
consumption in each cycle compared to CV-SRAM. Besides, energy
consumption in each cycle of proposed SRAM and CV-SRAM
investigated analytically, the results of which are in good agreement
with the simulation results.
Abstract: This paper presents the decoder design for the single error correcting and double error detecting code proposed by the authors in an earlier paper. The speed of error detection and correction of a code is largely dependent upon the associated encoder and decoder circuits. The complexity and the speed of such circuits are determined by the number of 1?s in the parity check matrix (PCM). The number of 1?s in the parity check matrix for the code proposed by the authors are fewer than in any currently known single error correcting/double error detecting code. This results in simplified encoding and decoding circuitry for error detection and correction.
Abstract: Clustering is a very well known technique in data mining. One of the most widely used clustering techniques is the kmeans algorithm. Solutions obtained from this technique depend on the initialization of cluster centers and the final solution converges to local minima. In order to overcome K-means algorithm shortcomings, this paper proposes a hybrid evolutionary algorithm based on the combination of PSO, SA and K-means algorithms, called PSO-SA-K, which can find better cluster partition. The performance is evaluated through several benchmark data sets. The simulation results show that the proposed algorithm outperforms previous approaches, such as PSO, SA and K-means for partitional clustering problem.
Abstract: A piston cylinder based high pressure differential
thermal analyzer system is developed to investigate phase
transformations, melting, glass transitions, crystallization behavior of
inorganic materials, glassy systems etc., at ambient to 4 GPa and at
room temperature to 1073 K. The pressure is calibrated by the phase
transition of bismuth and ytterbium and temperature is calibrated
by using thermocouple data chart. The system developed is
calibrated using benzoic acid, ammonium nitrate and it has a
pressure and temperature control of ± 8.9 x 10 -4 GPa , ± 2 K
respectively. The phase transition of Asx Te100-x chalcogenides,
ferrous oxide and strontium boride are studied using the
indigenously developed system.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.
Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: Seismic design may require non-conventional
concept, due to the fact that the stiffness and layout of the structure
have a great effect on the overall structural behaviour, on the seismic
load intensity as well as on the internal force distribution. To find an
economical and optimal structural configuration the key issue is the
optimal design of the lateral load resisting system. This paper focuses
on the optimal design of regular, concentric braced frame (CBF)
multi-storey steel building structures. The optimal configurations are
determined by a numerical method using genetic algorithm approach,
developed by the authors. Aim is to find structural configurations
with minimum structural cost. The design constraints of objective
function are assigned in accordance with Eurocode 3 and Eurocode 8
guidelines. In this paper the results are presented for various building
geometries, different seismic intensities, and levels of energy
dissipation.
Abstract: Recently, lots of researchers are attracted to retrieving
multimedia database by using some impression words and their values.
Ikezoe-s research is one of the representatives and uses eight pairs of
opposite impression words. We had modified its retrieval interface and
proposed '2D-RIB'. In '2D-RIB', after a retrieval person selects a
single basic music, the system visually shows some other music
around the basic one along relative position. He/she can select one of
them fitting to his/her intention, as a retrieval result. The purpose of
this paper is to improve his/her satisfaction level to the retrieval result
in 2D-RIB. One of our extensions is to define and introduce the
following two measures: 'melody goodness' and 'general acceptance'.
We implement them in different five combinations. According to an
evaluation experiment, both of these two measures can contribute to
the improvement. Another extension is three types of customization.
We have implemented them and clarified which customization is
effective.
Abstract: The present research was designed to investigate the
anti-microbial activity of aristolochic acid from the root of
Aristolochia bracteata. From the methanolic & ethyl extract extracts
of Aristolochia bracteata aristolochic acid I was isolated and
conformed through IR, NMR & MS. The percentage purity of
aristolochic acid I was determined by UV & HPLC method. Antibacterial
activity of extracts of Aristolochia bracteata and the
isolated compound was determined by disc diffusion method. The
results reveled that the isolated aristolochic acid from methanolic
extract was more pure than the compound from ethyl acetate extract.
The various extracts (500μg/disc) of Aristolochia bracteata showed
moderate antibacterial activity with the average zone of inhibition of
7-18 mm by disc diffusion method. Among the extracts, ethyl acetate
& methanol extracts were shown good anti-microbial activity and the
growth of E.coli (18 mm) was strongly inhibited. Microbial assay of
isolated compound (Aristolochic acid I) from ethyl acetate &
methanol extracts were shown good antimicrobial activity and the
zone of inhibition of both at higher concentration 50 μg/ml was
similar with the standard aristolochic acid. It may be concluded that
the isolated compound of aristolochic acid I has good anti-bacterial
activity.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: Studies on Simultaneous Saccharification and Fermentation (SSF) of corn flour, a major agricultural product as the substrate using starch digesting glucoamylase enzyme derived from Aspergillus niger and non starch digesting and sugar fermenting Saccharomyces cerevisiae in a batch fermentation. Experiments based on Central Composite Design (CCD) were conducted to study the effect of substrate concentration, pH, temperature, enzyme concentration on Ethanol Concentration and the above parameters were optimized using Response Surface Methodology (RSM). The optimum values of substrate concentration, pH, temperature and enzyme concentration were found to be 160 g/l, 5.5, 30°C and 50 IU respectively. The effect of inoculums age on ethanol concentration was also investigated. The corn flour solution equivalent to 16% initial starch concentration gave the highest ethanol concentration of 63.04 g/l after 48 h of fermentation at optimum conditions of pH and temperature. Monod model and Logistic model were used for growth kinetics and Leudeking – Piret model was used for product formation kinetics.
Abstract: In this study, we propose a network architecture for
providing secure access to information resources of enterprise
network from remote locations in a wireless fashion. Our proposed
architecture offers a very promising solution for organizations which
are in need of a secure, flexible and cost-effective remote access
methodology. Security of the proposed architecture is based on
Virtual Private Network technology and a special role based access
control mechanism with location and time constraints. The flexibility
mainly comes from the use of Internet as the communication medium
and cost-effectiveness is due to the possibility of in-house
implementation of the proposed architecture.
Abstract: Performance of a cobalt doped sol-gel derived silica (Co/SiO2) catalyst for Fischer–Tropsch synthesis (FTS) in slurryphase reactor was studied using paraffin wax as initial liquid media. The reactive mixed gas, hydrogen (H2) and carbon monoxide (CO) in a molar ratio of 2:1, was flowed at 50 ml/min. Braunauer-Emmett- Teller (BET) surface area and X-ray diffraction (XRD) techniques were employed to characterize both the specific surface area and crystallinity of the catalyst, respectively. The reduction behavior of Co/SiO2 catalyst was investigated using the Temperature Programmmed Reduction (TPR) method. Operating temperatures were varied from 493 to 533K to find the optimum conditions to maximize liquid fuels production, gasoline and diesel.
Abstract: Active Vibration Control (AVC) is an important
problem in structures. One of the ways to tackle this problem is to
make the structure smart, adaptive and self-controlling. The objective
of active vibration control is to reduce the vibration of a system by
automatic modification of the system-s structural response. This
paper features the modeling and design of a Periodic Output
Feedback (POF) control technique for the active vibration control of
a flexible Timoshenko cantilever beam for a multivariable case with
2 inputs and 2 outputs by retaining the first 2 dominant vibratory
modes using the smart structure concept. The entire structure is
modeled in state space form using the concept of piezoelectric
theory, Timoshenko beam theory, Finite Element Method (FEM) and
the state space techniques. Simulations are performed in MATLAB.
The effect of placing the sensor / actuator at 2 finite element
locations along the length of the beam is observed. The open loop
responses, closed loop responses and the tip displacements with and
without the controller are obtained and the performance of the smart
system is evaluated for active vibration control.