Abstract: This research aimed to modify pineapple leaf paper
(PALP) for using as wet media in the evaporation cooling system by
improving wet mechanical property (tensile strength) without
compromising water absorption property. Polyamideamineepichorohydrin
resin (PAE) and carboxymethylcellulose (CMC)
were used to strengthen the paper, and the PAE and CMC ratio of
80:20 showed the optimum wet and dry tensile index values, which
were higher than those of the commercial cooling pad (CCP).
Compared with CCP, PALP itself and all the PAE/CMC modified
PALP possessed better water absorption. The PAE/CMC modified
PALP had potential to become a new type of wet media.
Abstract: Recently, malware attacks have become more serious
over the Internet by e-mail, denial of service (DoS) or distributed
denial of service (DDoS). The Botnets have become a significant part
of the Internet malware attacks. The traditional botnets include three
parts – botmaster, command and control (C&C) servers and bots. The
C&C servers receive commands from botmaster and control the
distributions of computers remotely. Bots use DNS to find the
positions of C&C server. In this paper, we propose an advanced hybrid
peer-to-peer (P2P) botnet 2.0 (AHP2P botnet 2.0) using web 2.0
technology to hide the instructions from botmaster into social sites,
which are regarded as C&C servers. Servent bots are regarded as
sub-C&C servers to get the instructions from social sites. The AHP2P
botnet 2.0 can evaluate the performance of servent bots, reduce DNS
traffics from bots to C&C servers, and achieve harder detection bots
actions than IRC-based botnets over the Internet.
Abstract: This study was aimed for investigating of
manufacturing high aluminum content Mg alloys using a horizontal
twin roll caster. Recently, weight saving has been key issues for lighter
transport equipments as well as electronic component parts. As
alternative materials to aluminum alloys, developing magnesium alloy
with higher strength has been expected. Normally high Aluminum
content Mg alloy has poor ductility and is difficult to be rolled because
of its high strength. However, twin roll casting process is suitable for
manufacturing wrought Mg alloys because materials can be cast
directly from molten metal. In this study, manufacturing of high
aluminum content magnesium alloy sheet using the roll casting
process has been carried out. Effects of manufacturing parameter, such
as roll velocity, pouring temperature and roll gap, on casting was
investigated. A microscopic observation of the crystals of cross section
of as cast strip as well as rolled strip was conducted.
Abstract: The aim of this paper is to present current and future
procedures in castings procurement. Differences in procurement are
highlighted. The supplier selection criteria used in practice is
compared to literature findings. Different trends related to supply
chains are presented and it is described how they are reflected in
reality to castings procurement. To fulfil the aim, interviews were
conducted in nine companies using castings. It was found that largest
casting users have the most subcontractor foundries and it is more
typical that they have multiple suppliers for the same parts. Currently
only two companies out of nine purchase castings outside Europe,
but the others are also progressing in the same direction. The main
reason is the need to lower purchasing costs. Another trend is that all
companies want to buy cast components or sub-assemblies instead of
raw castings from foundries. It was found that price is a main
supplier selection criterion. All companies use competitive bidding in
supplier selection.
Abstract: In this study, the adhesion of ice to solid substrates
with different surface properties is compared. Clear ice, similar to
atmospheric in-flight icing encounters, is accreted on the different
substrates under controlled conditions. The ice adhesion behavior is
investigated by means of a dynamic vibration testing technique with
an electromagnetic shaker initiating ice de-bonding in the interface
between the substrate and the ice. The results of the experiments
reveal that the affinity for ice accretion is significantly influenced by
the water contact angle of the respective sample.
Abstract: The introduction of mass-customization has enabled
new ways to treat patients within medicine. However, the
introduction of industrialized treatments has also meant new
obstacles. The purpose of this study was to introduce and
theoretically test a method for improving dental crown fit. The
optimization method allocates support points in order to check the
final variation for dental crowns. Three different types of geometries
were tested and compared. The three geometries were also divided
into three sub-geometries: Current method, Optimized method and
Feasible method. The Optimized method, using the whole surface for
support points, provided the best results. The results support the
objective of the study. It also seems that the support optimization
method can dramatically improve the robustness of dental crown
treatments.
Abstract: This paper attempts to explore a new method to
improve the teaching of algorithmic for beginners. It is well known
that algorithmic is a difficult field to teach for teacher and complex to
assimilate for learner. These difficulties are due to intrinsic
characteristics of this field and to the manner that teachers (the
majority) apprehend its bases. However, in a Technology Enhanced
Learning environment (TEL), assessment, which is important and
indispensable, is the most delicate phase to implement, for all
problems that generate (noise...). Our objective registers in the
confluence of these two axes. For this purpose, EASEL focused
essentially to elaborate an assessment approach of algorithmic
competences in a TEL environment. This approach consists in
modeling an algorithmic solution according to basic and elementary
operations which let learner draw his/her own step with all autonomy
and independently to any programming language. This approach
assures a trilateral assessment: summative, formative and diagnostic
assessment.
Abstract: Today, canines are still used effectively in acceleration detection situation. However, this method is becoming impractical in modern age and a new automated replacement to the canine is required. This paper reports the design of an innovative accelerant detector. Designing an accelerant detector is a long process as is any design process; therefore, a solution to the need for a mobile, effective accelerant detector is hereby presented. The device is simple and efficient to ensure that any accelerant detection can be conducted quickly and easily. The design utilizes Ultra Violet (UV) light to detect the accelerant. When the UV light shines on an accelerant, the hydrocarbons in the accelerant emit florescence. The advantages of using the UV light to detect accelerant are also outlined in this paper. The mobility of the device is achieved by using a Direct Current (DC) motor to run tank tracks. Tank tracks were chosen as to ensure that the device will be mobile in the rough terrain of a fire site. The materials selected for the various parts are also presented. A Solid Works Simulation was also conducted on the stresses in the shafts and the results are presented. This design is an innovative solution which offers a user friendly interface. The design is also environmentally friendly, ecologically sound and safe to use.
Abstract: Liquid-liquid extraction is a process using two immiscible
liquids to extract compounds from one phase without high
temperature requirement. Mostly, the technical implementation of
this process is carried out in mixer-settlers or extraction columns. In
real chemical processes, chemicals may have high viscosity and
contain impurities. These impurities may change the settling behavior
of the process without measurably changing the physical properties
of the phases. In the current study, the settling behavior and the affected
parameters in a high-viscosity system were observed. Batchsettling
experiments were performed to experimentally quantify the
settling behavior and the mixer-settler model of Henschke [1] was
used to evaluate the behavior of the toluene + water system. The
viscosity of the system was increased by adding polyethylene glycol
4000 to the aqueous phase. NaCl and Na2SO4 were used to study the
influence of electrolytes. The results from this study show that increasing
the viscosity of water has a higher influence on the settling
behavior in comparison to the effects of the electrolytes. It can be
seen from the experiments that at high salt concentrations, there was
no effect on the settling behavior.
Abstract: A multi-rate discrete-time model, whose response
agrees exactly with that of a continuous-time original at all sampling
instants for any sampling periods, is developed for a linear system,
which is assumed to have multiple real eigenvalues. The sampling
rates can be chosen arbitrarily and individually, so that their ratios
can even be irrational. The state space model is obtained as a
combination of a linear diagonal state equation and a nonlinear output
equation. Unlike the usual lifted model, the order of the proposed
model is the same as the number of sampling rates, which is less than
or equal to the order of the original continuous-time system. The
method is based on a nonlinear variable transformation, which can be
considered as a generalization of linear similarity transformation,
which cannot be applied to systems with multiple eigenvalues in
general. An example and its simulation result show that the proposed
multi-rate model gives exact responses at all sampling instants.
Abstract: The winding hot-spot temperature is one of the most
critical parameters that affect the useful life of the power
transformers. The winding hot-spot temperature can be calculated as
function of the top-oil temperature that can estimated by using the
ambient temperature and transformer loading measured data. This
paper proposes the estimation of the top-oil temperature by using a
method based on Least Squares Support Vector Machines approach.
The estimated top-oil temperature is compared with measured data of
a power transformer in operation. The results are also compared with
methods based on the IEEE Standard C57.91-1995/2000 and
Artificial Neural Networks. It is shown that the Least Squares
Support Vector Machines approach presents better performance than
the methods based in the IEEE Standard C57.91-1995/2000 and
artificial neural networks.
Abstract: In this paper, four carbazole-based D-D-π-A organic
dyes code as CCT2A, CCT3A, CCT1PA and CCT2PA were reported.
A series of these organic dyes containing identical donor and
acceptor group but different π-system. The effect of replacing of
thiophene by phenyl thiophene as π-system on the physical
properties has been focused. The structural, energetic properties and
absorption spectra were theoretically investigated by means of
Density Functional Theory (DFT) and Time-Dependent Density
Functional Theory (TD-DFT). The results show that nonplanar
conformation due to steric hindrance in donor part (cabazolecarbazole
unit) of dye molecule can prevent unfavorable dye
aggregation. By means of the TD-DFT method, the absorption
spectra were calculated by B3LYP and BHandHLYP to study the
affect of hybrid functional on the excitation energy (Eg). The results
revealed the increasing of thiophene units not only resulted in
decreasing of Eg, but also found the shifting of absorption spectra to
higher wavelength. TD-DFT/BHandHLYP calculated results are
more strongly agreed with the experimental data than B3LYP
functions. Furthermore, the adsorptions of CCT2A and CCT3A on the
TiO2 anatase (101) surface were carried out by mean of the chemical
periodic calculation. The result exhibit the strong adsorption energy.
The calculated results provide our new organic dyes can be
effectively used as dye for Dye Sensitized Solar Cell (DSC).
Abstract: This paper developed the c-Chart based on a Zero- Inflated Poisson (ZIP) processes that approximated by a geometric distribution with parameter p. The p estimated that fit for ZIP distribution used in calculated the mean, median, and variance of geometric distribution for constructed the c-Chart by three difference methods. For cg-Chart, developed c-Chart by used the mean and variance of the geometric distribution constructed control limits. For cmg-Chart, the mean used for constructed the control limits. The cme- Chart, developed control limits of c-Chart from median and variance values of geometric distribution. The performance of charts considered from the Average Run Length and Average Coverage Probability. We found that for an in-control process, the cg-Chart is superior for low level of mean at all level of proportion zero. For an out-of-control process, the cmg-Chart and cme-Chart are the best for mean = 2, 3 and 4 at all level of parameter.
Abstract: Since 2004, we have been developing an in-situ storage image sensor (ISIS) that captures more than 100 consecutive images at a frame rate of 10 Mfps with ultra-high sensitivity as well as the video camera for use with this ISIS. Currently, basic research is continuing in an attempt to increase the frame rate up to 100 Mfps and above. In order to suppress electro-magnetic noise at such high frequency, a digital-noiseless imaging transfer scheme has been developed utilizing solely sinusoidal driving voltages. This paper presents highly efficient-yet-accurate expressions to estimate attenuation as well as phase delay of driving voltages through RC networks of an ultra-high-speed image sensor. Elmore metric for a fundamental RC chain is employed as the first-order approximation. By application of dimensional analysis to SPICE data, we found a simple expression that significantly improves the accuracy of the approximation. Similarly, another simple closed-form model to estimate phase delay through fundamental RC networks is also obtained. Estimation error of both expressions is much less than previous works, only less 2% for most of the cases . The framework of this analysis can be extended to address similar issues of other VLSI structures.
Abstract: Semiconductor nanomaterials like TiO2 nanoparticles
(TiO2-NPs) approximately less than 100 nm in diameter have become
a new generation of advanced materials due to their novel and
interesting optical, dielectric, and photo-catalytic properties. With the
increasing use of NPs in commerce, to date few studies have
investigated the toxicological and environmental effects of NPs.
Motivated by the importance of TiO2-NPs that may contribute to the
cancer research field especially from the treatment prospective
together with the fractal analysis technique, we have investigated the
effect of TiO2-NPs on colony morphology in the dark condition
using fractal dimension as a key morphological characterization
parameter. The aim of this work is mainly to investigate the cytotoxic
effects of TiO2-NPs in the dark on the growth of human cervical
carcinoma (HeLa) cell colonies from morphological aspect. The in
vitro studies were carried out together with the image processing
technique and fractal analysis. It was found that, these colonies were
abnormal in shape and size. Moreover, the size of the control
colonies appeared to be larger than those of the treated group. The
mean Df +/- SEM of the colonies in untreated cultures was
1.085±0.019, N= 25, while that of the cultures treated with TiO2-NPs
was 1.287±0.045. It was found that the circularity of the control
group (0.401±0.071) is higher than that of the treated group
(0.103±0.042). The same tendency was found in the diameter
parameters which are 1161.30±219.56 μm and 852.28±206.50 μm
for the control and treated group respectively. Possible explanation of
the results was discussed, though more works need to be done in
terms of the for mechanism aspects. Finally, our results indicate that
fractal dimension can serve as a useful feature, by itself or in
conjunction with other shape features, in the classification of cancer
colonies.
Abstract: Periphyton development and composition were
studied in three different treatments: (i) two fishpond units of
wetland-type wastewater treatment pond systems, (ii) two fishponds
in combined intensive-extensive fish farming systems and (iii) three
traditional polyculture fishponds. Results showed that amounts of
periphyton developed in traditional polyculture fishponds (iii) were
different compared to the other treatments (i and ii), where the main
function of ponds was stated wastewater treatment. Negative
correlation was also observable between water quality parameters
and periphyton production. The lower trophity, halobity and
saprobity level of ponds indicated higher amount of periphyton. The
dry matter content of periphyton was significantly higher in the
samples, which were developed in traditional polyculture fishponds
(2.84±3.02 g m-2 day-1, whereby the ash content in dry matter 74%),
than samples taken from (i) (1.60±2.32 g m-2 day-1, 61%) and (ii)
fishponds (0.65±0.45 g m-2 day-1, 81%).
Abstract: The events of October 2010, where terrorists managed to get explosive devices onboard of three passenger aircrafts and two air freighters, demonstrated weaknesses of the international air cargo and airmail security. Ever since, postal security has gained interest among policymakers and authorities. This study augments the limited body of academic literature on the topic bydemarcating areas of postal security, identifying relevant stakeholders in each area, and investigating why these stakeholders engage in postal security. Research is based on a case study on Swiss Post’s mail service.
Abstract: The research objective was to study the toxicity of silver nanoparticles in aquatic organisms. Three forms of free silver ion nanoparticles (Ag+), silver nano particles (nano-Ag0) and silver oxide nanoparticles (nano Ag2O) were examined for toxic effects with Chlorella sp. and Moina macrocopa. The results showed that the toxicity of three silver ion forms to both organisms was examined
Abstract: Service innovations are central concerns in fast
changing environment. Due to the fitness in customer demands and
advances in information technologies (IT) in service management, an
expanded conceptualization of e-service innovation is required.
Specially, innovation practices have become increasingly more
challenging, driving managers to employ a different open innovation
model to maintain competitive advantages. At the same time, firms
need to interact with external and internal customers in innovative
environments, like the open innovation networks, to co-create values.
Based on these issues, an important conceptual framework of e-service
innovation is developed. This paper aims to examine the contributing
factors on e-service innovation and firm performance, including
financial and non-financial aspects. The study concludes by showing
how e-service innovation will play a significant role in growing the
overall values of the firm. The discussion and conclusion will lead to a
stronger understanding of e-service innovation and co-creating values
with customers within open innovation networks.
Abstract: The rapid development of manufacturing and information systems has caused significant changes in manufacturing environments in recent decades. Mass production has given way to flexible manufacturing systems, in which an important characteristic is customized or "on demand" production. In this scenario, the seamless and without gaps information flow becomes a key factor for success of enterprises. In this paper we present a framework to support the mapping of features into machining workingsteps compliant with the ISO 14649 standard (known as STEP-NC). The system determines how the features can be made with the available manufacturing resources. Examples of the mapping method are presented for features such as a pocket with a general surface.