Abstract: Although the level crossing concept has been the subject of intensive investigation over the last few years, certain problems of great interest remain unsolved. One of these concern is distribution of threshold levels. This paper presents a new threshold level allocation schemes for level crossing based on nonuniform sampling. Intuitively, it is more reasonable if the information rich regions of the signal are sampled finer and those with sparse information are sampled coarser. To achieve this objective, we propose non-linear quantization functions which dynamically assign the number of quantization levels depending on the importance of the given amplitude range. Two new approaches to determine the importance of the given amplitude segment are presented. The proposed methods are based on exponential and logarithmic functions. Various aspects of proposed techniques are discussed and experimentally validated. Its efficacy is investigated by comparison with uniform sampling.
Abstract: When a small H/W IP is designed, we can develop an
appropriate verification environment by observing the simulated
signal waves, or using the serial test vectors for the fixed output. In the
case of design and verification of a massive parallel processor with
multiple IPs, it-s difficult to make a verification system with existing
common verification environment, and to verify each partial IP. A
TestDrive verification environment can build easy and reliable
verification system that can produce highly intuitive results by
applying Modelsim and SystemVerilog-s DPI. It shows many
advantages, for example a high-level design of a GPGPU processor
design can be migrate to FPGA board immediately.
Abstract: IPN and IPE sections, which are commonly used European I shapes, are widely used in steel structures as cantilever beams to support overhangs. A considerable number of studies exist on calculating lateral torsional buckling load of I sections. However, most of them provide series solutions or complex closed-form equations. In this paper, a simple equation is presented to calculate lateral torsional buckling load of IPN and IPE section cantilever beams. First, differential equation of lateral torsional buckling is solved numerically for various loading cases. Then a parametric study is conducted on results to present an equation for lateral torsional buckling load of European IPN and IPE beams. Finally, results obtained by presented equation are compared to differential equation solutions and finite element model results. ABAQUS software is utilized to generate finite element models of beams. It is seen that the results obtained from presented equation coincide with differential equation solutions and ABAQUS software results. It can be suggested that presented formula can be safely used to calculate critical lateral torsional buckling load of European IPN and IPE section cantilevers.
Abstract: Image mosaicing techniques are usually employed to offer researchers a wider field of view of microscopic image of biological samples. a mosaic is commonly achieved using automated microscopes and often with one “color" channel, whether it refers to natural or fluorescent analysis. In this work we present a method to achieve three subsequent mosaics of the same part of a stem cell culture analyzed in phase contrast and in fluorescence, with a common non-automated inverted microscope. The mosaics obtained are then merged together to mark, in the original contrast phase images, nuclei and cytoplasm of the cells referring to a mosaic of the culture, rather than to single images. The experiments carried out prove the effectiveness of our approach with cultures of cells stained with calcein (green/cytoplasm and nuclei) and hoechst (blue/nuclei) probes.
Abstract: Resource discovery is one of the chief services of a grid. A new approach to discover the provenances in grid through learning automata has been propounded in this article. The objective of the aforementioned resource-discovery service is to select the resource based upon the user-s applications and the mercantile yardsticks that is to say opting for an originator which can accomplish the user-s tasks in the most economic manner. This novel service is submitted in two phases. We proffered an applicationbased categorization by means of an intelligent nerve-prone plexus. The user in question sets his or her application as the input vector of the nerve-prone nexus. The output vector of the aforesaid network limns the appropriateness of any one of the resource for the presented executive procedure. The most scrimping option out of those put forward in the previous stage which can be coped with to fulfill the task in question is picked out. Te resource choice is carried out by means of the presented algorithm based upon the learning automata.
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.
Abstract: This paper examines the role and the place of
transdisciplinarity in the urbanism of the 21st century, with the
emphasis on Montenegro urbanism. Global processes require a
systematic strategy and systemic synergistic engagement in the
development of cities in 21st centuries. Urbanism as a profession and
a discipline should be developed parallel and in correlation, based on
the principles of integrality and communication skills, in order to
enable development of the sustainable urban system. The importance
of integrated urbanism and other disciplines are also emphasized as
well as their synergies activities. The paper also presents the positive
examples of urban theory and practice in the world, which influenced
the direction of development of the modern urbanism.
Transdisciplinarity is a priority methodology for sustainable urban
development, which is insufficiently developed in Montenegro, but
there is a basis for its development. It is necessary to unite different
social sensibilities, academic and non-academic knowledge, as well
as the public and private sectors in order to develop holistic,
inclusive and sustainable urban spaces of the 21st centuries.
Abstract: In this paper, an efficient wave concept iterative
process (WCIP) with auxiliary Sources is presented for full wave
investigation of an active microwave structure on micro strip
technology. Good agreement between the experimental and
simulation results is observed.
Abstract: Application of Information Technology (IT) has
revolutionized the functioning of business all over the world. Its
impact has been felt mostly among the information of dependent
industries. Tourism is one of such industry. The conceptual
framework in this study represents an innovation of travel
information searching system on mobile devices which is used as
tools to deliver travel information (such as hotels, restaurants, tourist
attractions and souvenir shops) for each user by travelers
segmentation based on data mining technique to segment the tourists-
behavior patterns then match them with tourism products and
services. This system innovation is designed to be a knowledge
incremental learning. It is a marketing strategy to support business to
respond traveler-s demand effectively.
Abstract: Methods for organizing web data into groups in order
to analyze web-based hypertext data and facilitate data availability
are very important in terms of the number of documents available
online. Thereby, the task of clustering web-based document structures
has many applications, e.g., improving information retrieval on the
web, better understanding of user navigation behavior, improving web
users requests servicing, and increasing web information accessibility.
In this paper we investigate a new approach for clustering web-based
hypertexts on the basis of their graph structures. The hypertexts will
be represented as so called generalized trees which are more general
than usual directed rooted trees, e.g., DOM-Trees. As a important
preprocessing step we measure the structural similarity between the
generalized trees on the basis of a similarity measure d. Then,
we apply agglomerative clustering to the obtained similarity matrix
in order to create clusters of hypertext graph patterns representing
navigation structures. In the present paper we will run our approach
on a data set of hypertext structures and obtain good results in
Web Structure Mining. Furthermore we outline the application of
our approach in Web Usage Mining as future work.
Abstract: In automotive systems almost all steps concerning the
calibration of several control systems, e.g., low idle governor or
boost pressure governor, are made with the vehicle because the timeto-
production and cost requirements on the projects do not allow for
the vehicle analysis necessary to build reliable models. Here is
presented a procedure using parametric and NN (neural network)
models that enables the generation of vehicle system models based
on normal ECU engine control unit) vehicle measurements. These
models are locally valid and permit pre and follow-up calibrations so
that, only the final calibrations have to be done with the vehicle.
Abstract: A big organization may have multiple branches spread across different locations. Processing of data from these branches becomes a huge task when innumerable transactions take place. Also, branches may be reluctant to forward their data for centralized processing but are ready to pass their association rules. Local mining may also generate a large amount of rules. Further, it is not practically possible for all local data sources to be of the same size. A model is proposed for discovering valid rules from different sized data sources where the valid rules are high weighted rules. These rules can be obtained from the high frequency rules generated from each of the data sources. A data source selection procedure is considered in order to efficiently synthesize rules. Support Equalization is another method proposed which focuses on eliminating low frequency rules at the local sites itself thus reducing the rules by a significant amount.
Abstract: A SnO2/CdS/CdTe heterojunction was fabricated by
thermal evaporation technique. The fabricated cells were annealed at
573K for periods of 60, 120 and 180 minutes. The structural
properties of the solar cells have been studied by using X-ray
diffraction. Capacitance- voltage measurements were studied for the
as-prepared and annealed cells at a frequency of 102 Hz. The
capacitance- voltage measurements indicated that these cells are
abrupt. The capacitance decreases with increasing annealing time.
The zero bias depletion region width and the carrier concentration
increased with increasing annealing time. The carrier transport
mechanism for the CdS/CdTe heterojunction in dark is tunneling
recombination. The ideality factor is 1.56 and the reverse bias
saturation current is 9.6×10-10A. The energy band lineup for the n-
CdS/p-CdTe heterojunction was investigated using current - voltage
and capacitance - voltage characteristics.
Abstract: In this paper, the significant wave height at the Upper Gulf of Thailand and the changing of wave height at Bangkhuntien shoreline were simulated by using the Simulating WAves Nearshore Model (SWAN) version 40.51. The simulated results indicated that the significant wave height by SWAN model corresponded with the observed data. The results showed that the maximum significant wave height at the Bangkhuntien shoreline were 1.06-2.05 m. and the average significant wave height at the Bangkhuntien shoreline were 0.30-0.47 m. The significant wave height can be used to calculate the erosion through the Bangkhuntien shoreline. The erosion rates at the Bangkhuntien shoreline were prepared by using the aerial photo and they were about 1.80 m/yr. from 1980- 1986, 4.75 m/yr from 1987-1993, 15.28 m/yr from 1994-1996 and 10.03 m/yr from 1997-2002. The relation between the wave energy and the erosion were in good agreement. Therefore, the significant wave height was one of the major factors of the erosion at the Bangkhuntien shoreline.
Abstract: Geopolymer cement was evaluated as wellbore sealing material for carbon dioxide geosequestration application. Curing of cement system in saline water and strength testing in triaxial stress state condition under lateral confinement is relevant to primary cementing in CO2 geosequestration wellbore in saline aquifer. Geopolymer cement was cured in saline water (both at ambient conditions for 28 days and heated (60°C) conditions for 12 hours) and tested for triaxial strength at different levels of lateral confinement. Normal water and few other curing techniques were also studied both for geopolymer and API ‘G’ cement. Results reported were compared to evaluate the suitability of saline water for curing of geopolymer cement. Unconfined compression test results showed higher strength for curing in saline water than normal water. Besides, testing strength under lateral confinement demonstrated the material failure behavior from brittle to plastic.
Abstract: The learning society has currently transformed from 'wired society' to become 'mobile society' which is facilitated by wireless network. To suit to this new paradigm, m-learning was given birth and rapidly building its prospect to be included in the future curriculum. Research and studies on m-learning spruced up in numerous aspects but there is still scarcity in studies on curriculum design of m-learning. This study is a part of an ongoing bigger study probing into the m-learning curriculum for secondary schools. The paper reports on the first phase of the study which aims to probe into the needs of curriculum design for m-learning at the secondary school level and the researcher adopted the needs analysis method. Data accrued from responses on survey questionnaires based on Lickert-point scale were analyzed statistically. The findings from this preliminary study serve as a basis for m-learning curriculum development for secondary schools.
Abstract: Pressure vessels are usually operating at temperatures
where the conditions of linear elastic fracture mechanics are no
longer met because massive plasticity precedes crack propagation. In
this work the development of a surface crack in a pressure vessel
subject to bending and tension under elastic-plastic fracture
mechanics conditions was investigated. Finite element analysis was
used to evaluate the hydrostatic stress, the J-integral and crack
growth for semi-elliptical surface-breaking cracks. The results
showed non-uniform stress triaxiality and crack driving force around
the crack front at large deformation levels. Different ductile crack
extensions were observed which emphasis the dependent of ductile
tearing on crack geometry and type of loading. In bending the crack
grew only beneath the surface, and growth was suppressed at the
deepest segment. This contrasts to tension where the crack breaks
through the thickness with uniform growth along the entire crack
front except at the free surface. Current investigations showed that
the crack growth developed under linear elastic fracture mechanics
conditions will no longer be applicable under ductile tearing
scenarios.
Abstract: As known that efficiency of photovoltaic cells is not
high as desired level. Efficiency of PVs could be improved by
selecting convenient locations that have high solar irradiation,
sunshine duration, mild temperature, low level air pollution and dust
concentration. Additionally, some environmental parameters called
derating factors effect to decrease PV efficiencies such as cloud, high
temperature, aerosol optical depth, high dust concentration, shadow,
snow, humidity etc. In this paper, all parameters that effect PV
efficiency are considered in detail under climatic conditions of
Istanbul. A 750 Wp PV system with measurement devices is
constructed in Maslak campus of Istanbul Technical University.
Abstract: In the present work, an attempt has been made to
understand the feasibility of using UHF technique for identification
of any corona discharges/ arcing in insulating material due to water
droplets. The sensors of broadband type are useful for identification
of such discharges. It is realised that arcing initiated by liquid droplet
radiates UHF signals in the entire bandwidth up to 2 GHz. The
frequency content of the UHF signal generated due to corona/arcing
is not much varied in epoxy nanocomposites with different weight
percentage of clay content. The exfoliated/intercalated properties
were analysed through TEM studies. It is realized that corona
initiated discharges are of intermittent process. The hydrophobicity
of the material characterized through contact angle measurement. It
is realized that low Wt % of nanoclay content in epoxy resin reduces
the surface carbonization due to arcing/corona discharges. The results
of the study with gamma irradiated specimen indicates that contact
angle, discharge inception time and evaporation time of the liquid are
much lower than the virgin epoxy nanocomposite material.
Abstract: In today-s competitive global business environment,
the concept of supply chain management (SCM) continues to become
increasingly market-oriented, shifting the primary driver of the value
chain from supply to demand. Recent recommendations encourage
researchers to focus investigations on the supply chain process
integration (SCPI) capabilities that integrate a focal firm with its
network of suppliers and business customers to create value for it.
However, theoretical and empirical researches pertaining to the
antecedents and consequences of a focal firm-s SCPI capabilities have
been limited and piecemeal. The purpose of this study is to investigate
the critical determinants and consequences of a focal firm-s SCPI
capabilities. We test our proposed research framework using a sample
of 139 sales managers of manufacturing industries in Taiwan, our
research findings show that (1) both perceived business customer-s
power and focal firm-s market-oriented culture positively influences a
focal firm-s SCPI capabilities, and (2) SCPI capabilities positively
influence a focal firm-s SCM performance, both operational and
strategic benefits. Implications for practitioners and researchers and
suggestions for future research are also addressed in this study.