Abstract: Recently in the field of bridges that are newly built or
repaired, fast construction is required more than ever. For these
reasons, precast prefabricated bridge that enables rapid construction is
actively discussed and studied today. In South Korea, it is called
modular bridge. Cross beam is an integral component of modular
bridge. It functions for load distribution, reduction of bending
moment, resistance of horizontal strength on lateral upper structure. In
this study, the structural characteristics of domestic and foreign cross
beam types were compared. Based on this, alternative cross beam
connection types suitable for modular bridge were selected. And
bulb-T girder specimens were fabricated with each type of connection.
The behavior of each specimen was analyzed under static loading, and
cross beam connection type which is expected to be best suited to
modular bridge proposed.
Abstract: Conventional WBL is effective for meaningful student, because rote student learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote student-s intention and what influences it becomes important. Poorly designed user interface will discourage rote student-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance student-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote student-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: Mixed convection in two-dimensional shallow rectangular enclosure is considered. The top hot wall moves with constant velocity while the cold bottom wall has no motion. Simulations are performed for Richardson number ranging from Ri = 0.001 to 100 and for Reynolds number keeping fixed at Re = 408.21. Under these conditions cavity encompasses three regimes: dominating forced, mixed and free convection flow. The Prandtl number is set to 6 and the effects of cavity inclination on the flow and heat transfer are studied for different Richardson number. With increasing the inclination angle, interesting behavior of the flow and thermal fields are observed. The streamlines and isotherm plots and the variation of the Nusselt numbers on the hot wall are presented. The average Nusselt number is found to increase with cavity inclination for Ri ³ 1 . Also it is shown that the average Nusselt number changes mildly with the cavity inclination in the dominant forced convection regime but it increases considerably in the regime with dominant natural convection.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: When the failure function is monotone, some monotonic reliability methods are used to gratefully simplify and facilitate the reliability computations. However, these methods often work in a transformed iso-probabilistic space. To this end, a monotonic simulator or transformation is needed in order that the transformed failure function is still monotone. This note proves at first that the output distribution of failure function is invariant under the transformation. And then it presents some conditions under which the transformed function is still monotone in the newly obtained space. These concern the copulas and the dependence concepts. In many engineering applications, the Gaussian copulas are often used to approximate the real word copulas while the available information on the random variables is limited to the set of marginal distributions and the covariances. So this note catches an importance on the conditional monotonicity of the often used transformation from an independent random vector into a dependent random vector with Gaussian copulas.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any existing
network infrastructure or centralized administration. Because of the
limited transmission range of wireless network interfaces, multiple
"hops" may be needed to exchange data across the network. In order
to facilitate communication within the network, a routing protocol is
used to discover routes between nodes. The primary goal of such an
ad hoc network routing protocol is correct and efficient route
establishment between a pair of nodes so that messages may be
delivered in a timely manner. Route construction should be done
with a minimum of overhead and bandwidth consumption. This paper
examines two routing protocols for mobile ad hoc networks– the
Destination Sequenced Distance Vector (DSDV), the table- driven
protocol and the Ad hoc On- Demand Distance Vector routing
(AODV), an On –Demand protocol and evaluates both protocols
based on packet delivery fraction, normalized routing load, average
delay and throughput while varying number of nodes, speed and
pause time.
Abstract: This paper deals with the design of a periodic output
feedback controller for a flexible beam structure modeled with
Timoshenko beam theory, Finite Element Method, State space
methods and embedded piezoelectrics concept. The first 3 modes are
considered in modeling the beam. The main objective of this work is
to control the vibrations of the beam when subjected to an external
force. Shear piezoelectric sensors and actuators are embedded into
the top and bottom layers of a flexible aluminum beam structure, thus
making it intelligent and self-adaptive. The composite beam is
divided into 5 finite elements and the control actuator is placed at
finite element position 1, whereas the sensor is varied from position 2
to 5, i.e., from the nearby fixed end to the free end. 4 state space
SISO models are thus developed. Periodic Output Feedback (POF)
Controllers are designed for the 4 SISO models of the same plant to
control the flexural vibrations. The effect of placing the sensor at
different locations on the beam is observed and the performance of
the controller is evaluated for vibration control. Conclusions are
finally drawn.
Abstract: The article describes problems of city centers with regard to possibilities of their delimitation in a GIS environment. First the definitions and delimitations of a city centre which are in use are mentioned, furthermore a chosen case study (the historical centre of Olomouc city in the Czech Republic) is employed to describe the methods of delimitation in use. In addition to describing the current state, the article also deals with possibilities of delimitation of a city centre in GIS environment by means of several chosen approaches. The authors describe, compare and discuss the chosen methods and assess the achieved results and also applicability of the designed methods for other cities.
Abstract: Laser Doppler flowmetry is a modern method of noninvasive
microcirculation investigation. The aim of our study was to
use this method in the examination of patients with secondary
lymphedema of the lower extremities and obliterating atherosclerosis
of lower extremities. In the analysis of the amplitude-frequency
spectrum of secondary lymphedema patients we have identified
remarkable changes. To describe the changes we used a special
amplitude rate. In both of patients groups this rate was significally
(p
Abstract: Two optimized strategies were successfully established
to develop biomolecule-based magnetic nanoassemblies.
Streptavidin-coated and amine-coated magnetic nanoparticles were
chosen as model scaffolds onto which double-stranded DNA and
human immunoglobulin G were specifically conjugated in succession,
using biotin-streptavidin interaction or covalent cross-linkers. The
success of this study opens the prospect of developing selective and
sensitive nanoparticle-based structures for diagnostics or drug
delivery.
Abstract: In this paper, we carry over some of the results which
are valid on a certain class of Moufang-Klingenberg planes M(A)
coordinatized by an local alternative ring A := A(ε) = A+Aε of
dual numbers to finite projective Klingenberg plane M(A) obtained
by taking local ring Zq (where prime power q = pk) instead of A.
So, we show that the collineation group of M(A) acts transitively
on 4-gons, and that any 6-figure corresponds to only one inversible
m ∈ A.
Abstract: This paper presents PSS (Power system stabilizer) design based on optimal fuzzy PID (OFPID). OFPID based PSS design is considered for single-machine power systems. The main motivation for this design is to stabilize or to control low-frequency oscillation on power systems. Firstly, describing the linear PID control then to combine this PID control with fuzzy logic control mechanism. Finally, Fuzzy PID parameters (Kp. Kd, KI, Kupd, Kui) are tuned by Genetic Algorthm (GA) to reach optimal global stability. The effectiveness of the proposed PSS in increasing the damping of system electromechanical oscillation is demonstrated in a one-machine-infinite-bus system
Abstract: The hybridisation of genetic algorithm with heuristics has been shown to be one of an effective way to improve its performance. In this work, genetic algorithm hybridised with four heuristics including a new heuristic called neighbourhood improvement were investigated through the classical travelling salesman problem. The experimental results showed that the proposed heuristic outperformed other heuristics both in terms of quality of the results obtained and the computational time.
Abstract: In this paper we propose a novel method for human
face segmentation using the elliptical structure of the human head. It
makes use of the information present in the edge map of the image.
In this approach we use the fact that the eigenvalues of covariance
matrix represent the elliptical structure. The large and small
eigenvalues of covariance matrix are associated with major and
minor axial lengths of an ellipse. The other elliptical parameters are
used to identify the centre and orientation of the face. Since an
Elliptical Hough Transform requires 5D Hough Space, the Circular
Hough Transform (CHT) is used to evaluate the elliptical parameters.
Sparse matrix technique is used to perform CHT, as it squeeze zero
elements, and have only a small number of non-zero elements,
thereby having an advantage of less storage space and computational
time. Neighborhood suppression scheme is used to identify the valid
Hough peaks. The accurate position of the circumference pixels for
occluded and distorted ellipses is identified using Bresenham-s
Raster Scan Algorithm which uses the geometrical symmetry
properties. This method does not require the evaluation of tangents
for curvature contours, which are very sensitive to noise. The method
has been evaluated on several images with different face orientations.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Decision feedback equalizers are commonly employed to reduce the error caused by intersymbol interference. Here, an adaptive decision feedback equalizer is presented with a new adaptation algorithm. The algorithm follows a block-based approach of normalized least mean square (NLMS) algorithm with set-membership filtering and achieves a significantly less computational complexity over its conventional NLMS counterpart with set-membership filtering. It is shown in the results that the proposed algorithm yields similar type of bit error rate performance over a reasonable signal to noise ratio in comparison with the latter one.
Abstract: The in vitro culture procedure of purple nutsedge
(Cyperus rotundus L.) for multiple shoot induction and tuber
formation was established. Multiple shoots were significantly
induced from a single shoot of about 0.5 – 0.8 cm long, on Murashige
and Skoog (MS) medium supplemented with 4.44 μM 6-
benzyladinine (BA) alone or in combination with 2.85 μM 1-
indoleacetic acid (IAA), providing 17.6 and 15.3 shoots per explant
with 31.2 and 27.5 leaves per explant, respectively, within 6 weeks of
culturing. Moreover, MS medium supplemented with 4.44 μM BA
and 2.85 μM IAA was suitable for tuber induction, obtaining 5.9
tubers with 3.4 rhizomes per explant. In combination with ancymidol
and higher concentration of sucrose, 11.1 μM BA and 60 g/L sucrose
or 11.1 μM BA, 7.8 μM ancymidol and 60 g/L sucrose induced 3.5
tubers with 1.6 rhizomes or 3.5 tubers without rhizome, respectively.
However, MS medium containing 3.9 or 7.8 μM ancymidol in
combination with either 60 or 80 g/L sucrose enchanced significant
root formation at 20.9 – 23.6 roots per explant.
Abstract: With increasing number of wireless devices like
laptops, Wi-Fi Web Cams, network extenders, etc., a new kind of
problems appeared, mostly related to poor Wi-Fi throughput or
communication problems. In this paper an investigation on wireless
networks and it-s saturation in Vilnius City and its surrounding is
presented, covering the main problems of wireless saturation and
network load during day. Also an investigation on wireless channel
selection and noise levels were made, showing the impact of
neighbor AP to signal and noise levels and how it changes during the
day.
Abstract: In the course of the present work, plain (nonencapsulated)
and microencapsulated polyphenols were produced
using olive mill wastewater (OMW) as raw material, in order to be
used for enrichment of yogurt and dairy products. The OMW was
first clarified by using membrane technology and subsequently the
contained poly-phenols were isolated by adsorption-desorption
technique using selective macro-porous resins and finally recovered
in dry form after been processed by RO membrane technique
followed by freeze drying. Moreover, the polyphenols were
encapsulated in modified starch by freeze drying in order to mask the
color and bitterness effect and improve their functionality. The two
products were used successfully as additives in yogurt preparations
and the produced products were acceptable by the consumers and
presented with certain advantage to the plain yogurt. For the herein
proposed production scheme a patent application was already
submitted.
Abstract: In this paper a comprehensive model of a fossil fueled
power plant (FFPP) is developed in order to evaluate the
performance of a newly designed turbine follower controller.
Considering the drawbacks of previous works, an overall model is
developed to minimize the error between each subsystem model
output and the experimental data obtained at the actual power plant.
The developed model is organized in two main subsystems namely;
Boiler and Turbine. Considering each FFPP subsystem
characteristics, different modeling approaches are developed. For
economizer, evaporator, superheater and reheater, first order models
are determined based on principles of mass and energy conservation.
Simulations verify the accuracy of the developed models. Due to the
nonlinear characteristics of attemperator, a new model, based on a
genetic-fuzzy systems utilizing Pittsburgh approach is developed
showing a promising performance vis-à-vis those derived with other
methods like ANFIS. The optimization constraints are handled
utilizing penalty functions. The effect of increasing the number of
rules and membership functions on the performance of the proposed
model is also studied and evaluated. The turbine model is developed
based on the equation of adiabatic expansion. Parameters of all
evaluated models are tuned by means of evolutionary algorithms.
Based on the developed model a fuzzy PI controller is developed. It
is then successfully implemented in the turbine follower control
strategy of the plant. In this control strategy instead of keeping
control parameters constant, they are adjusted on-line with regard to
the error and the error rate. It is shown that the response of the
system improves significantly. It is also shown that fuel consumption
decreases considerably.