Abstract: Today due to rising levels of housing- necessities,
several problems have been raised regarding to urban quality of life.
The aim of the research is to study social and spatial aspects of
housing environment and to find out their interaction with the urban
quality of life. As a case of study two pilot areas of Famagusta city in
North Cyprus, were selected: Baykal, considered as an established
urban district and Tuzla, a newly developed peri-urban district. In
order to determine urban quality of life in planning and developing of
housing areas, social and spatial aspects of selected areas have been
examined, differences between them according to the planning policy
have been pointed out, advantages and disadvantages of housing
planning have been found. As a practical implementation of the
research a number of households in each selected area have been
interviewed in order to draw a conclusion.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.
Abstract: It is essential to have a uniform and calm flow field
for a settling tank to have high performance. In general, the
recirculation zones always occurred in sedimentation tanks. The
presence of these regions may have different effects. The nonuniformity
of the velocity field, the short-circuiting at the surface and
the motion of the jet at the bed of the tank that occurs because of the
recirculation in the sedimentation layer, are affected by the geometry
of the tank. There are some ways to decrease the size of these dead
zones, which would increase the performance. One of the ways is to
use a suitable baffle configuration. In this study, the presence of
baffle with different position has been investigated by a finite volume
method, with VOF (Volume of Fluid) model. Besides, the k-ε
turbulence model is used in the numerical calculations. The results
indicate that the best position of the baffle is obtained when the
volume of the recirculation region is minimized or is divided to
smaller part and the flow field trend to be uniform in the settling
zone.
Abstract: Malting is usually carried out on intact barley seed,
while hull is still attached to it. In this study, oat grain with and
without hull was subjected to controlled germination to optimize its
enzymes activity, in such a way that lipase has the lowest and α-
amylase and proteinase the highest activities. Since pH has a great
impact on the activity of the enzymes, the pH of germination media
was set up to 3 to 8. In dehulled oats, lipase and α-amylase had the
lowest and highest activities in pHs 3 and 6, respectively whereas the
highest proteinase activity was evidenced at pH 7 and 4 in the oats
with and without hull respectively. While measurements indicated
that the effect of hull on the enzyme activities particularly in lipase
and amylase at each level of the pH are significantly different, the
best results were obtained in those samples in which their hull had
been removed. However, since the similar lipase activity in
germinated dehulled oat were recorded at the pHs 4 and 5, therefore
it was concluded that pH 5 in dehulled oat seed may provide the
optimum enzyme activity for all the enzymes.
Abstract: Discovering new biological knowledge from the highthroughput biological data is a major challenge to bioinformatics today. To address this challenge, we developed a new approach for protein classification. Proteins that are evolutionarily- and thereby functionally- related are said to belong to the same classification. Identifying protein classification is of fundamental importance to document the diversity of the known protein universe. It also provides a means to determine the functional roles of newly discovered protein sequences. Our goal is to predict the functional classification of novel protein sequences based on a set of features extracted from each protein sequence. The proposed technique used datasets extracted from the Structural Classification of Proteins (SCOP) database. A set of spectral domain features based on Fast Fourier Transform (FFT) is used. The proposed classifier uses multilayer back propagation (MLBP) neural network for protein classification. The maximum classification accuracy is about 91% when applying the classifier to the full four levels of the SCOP database. However, it reaches a maximum of 96% when limiting the classification to the family level. The classification results reveal that spectral domain contains information that can be used for classification with high accuracy. In addition, the results emphasize that sequence similarity measures are of great importance especially at the family level.
Abstract: The role of neighborhood center as semi public (the
balance space) is disappeared in bonding between private and public
in new urbanism. In this way, a hierarchical principle in the
traditional neighborhood center appears to create or develop the
conditions for residents` relationships and belonging. This paper
evaluates significant of hierarchical principles of the neighborhood
center in residents` territoriality and its factors. In this way Miandeh
neighborhood center from Boshrooyeh city was determined as a case
study area. Results indicated that a hierarchical principle is the best
instrument to improve the territoriality as the subcomponent of place
belonging in residents. The findings help the urban designer to
revitalization the neighborhoods and proceedings in organization of
physical space.
Abstract: The capturing of gel electrophoresis image represents
the output of a DNA computing algorithm. Before this image is being
captured, DNA computing involves parallel overlap assembly (POA)
and polymerase chain reaction (PCR) that is the main of this
computing algorithm. However, the design of the DNA
oligonucleotides to represent a problem is quite complicated and is
prone to errors. In order to reduce these errors during the design stage
before the actual in-vitro experiment is carried out; a simulation
software capable of simulating the POA and PCR processes is
developed. This simulation software capability is unlimited where
problem of any size and complexity can be simulated, thus saving
cost due to possible errors during the design process. Information
regarding the DNA sequence during the computing process as well as
the computing output can be extracted at the same time using the
simulation software.
Abstract: The fast growing accessibility and capability of emerging technologies have fashioned enormous possibilities of designing, developing and implementing innovative teaching methods in the classroom. The global technological scenario has paved the way to new pedagogies in teaching-learning process focusing on technology based learning environment and its impact on student achievement. The present experimental study was conducted to determine the effectiveness of technology based learning environment on student achievement in English as a foreign language. The sample of the study was 90 students of 10th grade of a public school located in Islamabad. A pretest- posttest equivalent group design was used to compare the achievement of the two groups. A Pretest and A posttest containing 50 items each from English textbook were developed and administered. The collected data were statistically analyzed. The results showed that there was a significant difference between the mean scores of Experimental group and the Control group. The performance of Experimental group was better on posttest scores that indicted that teaching through technology based learning environment enhanced the achievement level of the students. On the basis of the results, it was recommended that teaching and learning through information and communication technologies may be adopted to enhance the language learning capability of the students.
Abstract: Vector quantization is a powerful tool for speech
coding applications. This paper deals with LPC Coding of speech
signals which uses a new technique called Multi Switched Split
Vector Quantization (MSSVQ), which is a hybrid of Multi, switched,
split vector quantization techniques. The spectral distortion
performance, computational complexity, and memory requirements
of MSSVQ are compared to split vector quantization (SVQ), multi
stage vector quantization(MSVQ) and switched split vector
quantization (SSVQ) techniques. It has been proved from results that
MSSVQ has better spectral distortion performance, lower
computational complexity and lower memory requirements when
compared to all the above mentioned product code vector
quantization techniques. Computational complexity is measured in
floating point operations (flops), and memory requirements is
measured in (floats).
Abstract: The greenhouse effect and limitations on carbon
dioxide emissions concern engine maker and the future of the
internal combustion engines should go toward substantially and
improved thermal efficiency engine. Homogeneous charge
compression ignition (HCCI) is an alternative high-efficiency
technology for combustion engines to reduce exhaust emissions and
fuel consumption. However, there are still tough challenges in the
successful operation of HCCI engines, such as controlling the
combustion phasing, extending the operating range, and high
unburned hydrocarbon and CO emissions. HCCI and the exploitation
of ethanol as an alternative fuel is one way to explore new frontiers
of internal combustion engines with an eye towards maintaining its
sustainability. This study was done to extend database knowledge
about HCCI with ethanol a fuel.
Abstract: Matrix metalloproteinase-3 (MMP3) is key member
of the MMP family, and is known to be present in coronary
atherosclerotic. Several studies have demonstrated that MMP-3
5A/6A polymorphism modify each transcriptional activity in allele
specific manner. We hypothesized that this polymorphism may play
a role as risk factor for development of coronary stenosis. The aim of
our study was to estimate MMP-3 (5A/6A) gene polymorphism on
interindividual variability in risk for coronary stenosis in an Iranian
population.DNA was extracted from white blood cells and genotypes
were obtained from coronary stenosis cases (n=95) and controls
(n=100) by PCR (polymerase chain reaction) and restriction
fragment length polymorphism techniques. Significant differences
between cases and controls were observed for MMP3 genotype
frequencies (X2=199.305, p< 0.001); the 6A allele was less
frequently seen in the control group, compared to the disease group
(85.79 vs. 78%, 6A/6A+5A/6A vs. 5A/5A, P≤0.001). These data
imply the involvement of -1612 5A/6A polymorphism in coronary
stenosis, and suggest that probably the 6A/6A MMP-3 genotype is a
genetic susceptibility factor for coronary stenosis.
Abstract: This paper presents an interval-based multi-attribute
decision making (MADM) approach in support of the decision
process with imprecise information. The proposed decision
methodology is based on the model of linear additive utility function
but extends the problem formulation with the measure of composite
utility variance. A sample study concerning with the evaluation of
electric generation expansion strategies is provided showing how the
imprecise data may affect the choice toward the best solution and
how a set of alternatives, acceptable to the decision maker (DM),
may be identified with certain confidence.
Abstract: Most Decision Support Systems (DSS) for waste
management (WM) constructed are not widely marketed and lack
practical applications. This is due to the number of variables and
complexity of the mathematical models which include the
assumptions and constraints required in decision making. The
approach made by many researchers in DSS modelling is to isolate a
few key factors that have a significant influence to the DSS. This
segmented approach does not provide a thorough understanding of
the complex relationships of the many elements involved. The
various elements in constructing the DSS must be integrated and
optimized in order to produce a viable model that is marketable and
has practical application. The DSS model used in assisting decision
makers should be integrated with GIS, able to give robust prediction
despite the inherent uncertainties of waste generation and the plethora
of waste characteristics, and gives optimal allocation of waste stream
for recycling, incineration, landfill and composting.
Abstract: In this work we numerically examine structures which
could confine light in nanometer areas. A system consisting of two silicon disks with in plane separation of a few tens of nanometers has
been studied first. The normalized unitless effective mode volume, Veff, has been calculated for the two lowest whispering gallery mode resonances. The effective mode volume is reduced significantly as the gap between the disks decreases. In addition, the effect of the substrate is also studied. In that case, Veff of approximately the same
value as the non-substrate case for a similar two disk system can be
obtained by using disks almost twice as thick. We also numerically examine a structure consisting of a circular slot waveguide which is formed into a silicon disk resonator. We show that the proposed structure could have high Q resonances thus raising the belief that it
is a very promising candidate for optical interconnects applications.
The study includes several numerical calculations for all the geometric parameters of the structure. It also includes numerical simulations of the coupling between a waveguide and the proposed
disk resonator leading to a very promising conclusion about its applicability.
Abstract: Every day human life experiences new equipments
more automatic and with more abilities. So the need for faster
processors doesn-t seem to finish. Despite new architectures and
higher frequencies, a single processor is not adequate for many
applications. Parallel processing and networks are previous solutions
for this problem. The new solution to put a network of resources on a
chip is called NOC (network on a chip). The more usual topology for
NOC is mesh topology. There are several routing algorithms suitable
for this topology such as XY, fully adaptive, etc. In this paper we
have suggested a new algorithm named Intermittent X, Y (IX/Y). We
have developed the new algorithm in simulation environment to
compare delay and power consumption with elders' algorithms.
Abstract: Transesterification of candlenut (aleurites moluccana)
oil with methanol using potassium hydroxide as catalyst was
studied. The objective of the present investigation was to produce
the methyl ester for use as biodiesel. The operation variables
employed were methanol to oil molar ratio (3:1 – 9:1), catalyst
concentration (0.50 – 1.5 %) and temperature (303 – 343K). Oil
volume of 150 mL, reaction time of 75 min were fixed as common
parameters in all the experiments. The concentration of methyl ester
was evaluated by mass balance of free glycerol formed which was
analyzed by using periodic acid. The optimal triglyceride conversion
was attained by using methanol to oil ratio of 6:1, potassium
hydroxide as catalyst was of 1%, at room temperature. Methyl ester
formed was characterized by its density, viscosity, cloud and pour
points. The biodiesel properties had properties similar to those of
diesel oil, except for the viscosity that was higher.
Abstract: In this paper we have developed a FDTD simulation
code which can treat wave propagation of a monopole antenna in a
metallic case which covers with PML, and performed a series of three
dimensional FDTD simulations of electromagnetic wave propagation
in this space .We also provide a measurement set up in antenna lab
and fortunately the simulations and measurements show good
agreement. According to simulation and measurement results, we
confirmed that the computer program which had been written in
FORTRAN, works correctly.
Abstract: Abrasive Jet Machining is an Unconventional
machining process in which the metal is removed from brittle and
hard material in the form of micro-chips. With increase in need of
materials like ceramics, composites, in manufacturing of various
Mechanical & Electronic components, AJM has become a useful
technique for micro machining. The present study highlights the
influence of different parameters like Pressure, SOD, Time, Abrasive
grain size, nozzle diameter on the Metal removal of FRP (Fiber
Reinforced Polymer) composite by Abrasive jet machining. The
results of the Experiments conducted were analyzed and optimized
with TAGUCHI method of Optimization and ANOVA for Optimal
Value.
Abstract: In this survey the process of crack propagation at the
toe of concrete gravity dam is investigated by applying principals
and criteria of linear elastic fracture mechanic. Simulating process of
earthquake conditions for three models of dam with different
geometrical condition, in empty reservoir under plain stress is
calculated through special fracture mechanic software FRANNC2D
[1] for determining fracture mechanic criteria. The outcomes showed
that in spite of the primary expectations, the simultaneous existence
of fillet in both toe and heel area (model 3), the rate of maximum
principal stress has not been decreased; however, even the maximum
principal stress has increased, so it caused stress intensity factors
increase which is undesirable. On the other hand, the dam with heel
fillet has shown the best attitude and it is because of items like
decreasing the rates of maximum and minimum principal stresses and
also is related to decreasing the rates of stress intensity factors for 1st
& 2nd modes of the model.
Abstract: In this paper, a numerical solution based on nonpolynomial
cubic spline functions is used for finding the solution of
boundary value problems which arise from the problems of calculus
of variations. This approximation reduce the problems to an explicit
system of algebraic equations. Some numerical examples are also
given to illustrate the accuracy and applicability of the presented
method.