Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: In this paper, we have examined the effect of process
parameter variation on the electrical characteristics of an LDMOS
device. The rate of change in the electrical parameters such as cut off
frequency, breakdown voltage and drain saturation current as a
function of the process parameters is investigated
Abstract: Fermented cassava flours (lafun) sold in Ogun and Oyo
States of Nigeria were collected from 10 markets for a period of two
months and analysed to determine their safety status. The presence of
trace metals was due to high vehicular movement around the drying
sites and markets. Cyanide and moisture contents of samples were
also determined to assess the adequacy of fermentation and drying.
The result showed that sample OWO was found to have the highest
amount of 16.02±0.12mg/kg cyanide while the lowest was found in
sample OJO with 10.51±0.10mg/kg. The results also indicated that
sample TVE had the highest moisture content of 18.50±0.20% while
sample OWO had the lowest amount of 12.46±0.47%. Copper and
lead levels were found to be highest in TVE with values 28.10mg/kg
and 1.1mg/kg respectively, while sample BTS had the lowest values
of 20.6mg/kg and 0.05mg/kg respectively. High value of cyanide
indicated inadequate fermentation.
Abstract: The enormous amount of solid waste generated poses
huge problems in waste management. It is therefore important to
gauge the awareness of the public with regards to waste management.
In this study, an instrument was developed to measure the beliefs,
attitudes and practices about waste management of school children as
an indication of their waste management awareness. This instrument
has showed that a positive awareness towards waste management
refers mainly to attitudes. However it is not easy for people to
practice waste management as a reflection of their awareness.
Abstract: Knowledge Discovery of Databases (KDD) is the
process of extracting previously unknown but useful and significant
information from large massive volume of databases. Data Mining is
a stage in the entire process of KDD which applies an algorithm to
extract interesting patterns. Usually, such algorithms generate huge
volume of patterns. These patterns have to be evaluated by using
interestingness measures to reflect the user requirements.
Interestingness is defined in different ways, (i) Objective measures
(ii) Subjective measures. Objective measures such as support and
confidence extract meaningful patterns based on the structure of the
patterns, while subjective measures such as unexpectedness and
novelty reflect the user perspective. In this report, we try to brief the
more widely spread and successful subjective measures and propose
a new subjective measure of interestingness, i.e. shocking.
Abstract: This paper presents an analytical solution to get a reliable estimation of the hydrodynamic pressure on gravity dams induced by vertical component earthquake when solving the fluid and dam interaction problem. Presented analytical technique is presented for calculation of earthquake-induced hydrodynamic pressure in the reservoir of gravity dams allowing for water compressibility and wave absorption at the reservoir bottom. This new analytical solution can take into account the effect of bottom material on seismic response of gravity dams. It is concluded that because the vertical component of ground motion causes significant hydrodynamic forces in the horizontal direction on a vertical upstream face, responses to the vertical component of ground motion are of special importance in analysis of concrete gravity dams subjected to earthquakes.
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: Compacted clay liners (CCLs) are the main materials
used in waste disposal landfills due to their low permeability. In this
study, the effect on the shear resistant of clays with inorganic salt
solutions as permeate fluid was experimentally investigated. For this
purpose, NaCl inorganic salt solution at concentrations of 2, 5, 10%
and deionized water were used. Laboratory direct shear and Vane
shear tests were conducted on three compacted clays with low,
medium and high plasticity. Results indicated that the solutions type
and its concentration affect the shear properties of the mixture. In the
light of this study, the influence magnitude of these inorganic salts in
varies concentrations in different clays were determined and more
suitable compacted clay with the compare of plasticity were found.
Abstract: This paper provides an in-depth study of Wireless
Sensor Network (WSN) application to monitor and control the
swiftlet habitat. A set of system design is designed and developed
that includes the hardware design of the nodes, Graphical User
Interface (GUI) software, sensor network, and interconnectivity for
remote data access and management. System architecture is proposed
to address the requirements for habitat monitoring. Such applicationdriven
design provides and identify important areas of further work
in data sampling, communications and networking. For this
monitoring system, a sensor node (MTS400), IRIS and Micaz radio
transceivers, and a USB interfaced gateway base station of Crossbow
(Xbow) Technology WSN are employed. The GUI of this monitoring
system is written using a Laboratory Virtual Instrumentation
Engineering Workbench (LabVIEW) along with Xbow Technology
drivers provided by National Instrument. As a result, this monitoring
system is capable of collecting data and presents it in both tables and
waveform charts for further analysis. This system is also able to send
notification message by email provided Internet connectivity is
available whenever changes on habitat at remote sites (swiftlet farms)
occur. Other functions that have been implemented in this system
are the database system for record and management purposes; remote
access through the internet using LogMeIn software. Finally, this
research draws a conclusion that a WSN for monitoring swiftlet
habitat can be effectively used to monitor and manage swiftlet
farming industry in Sarawak.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: This study examines the relationships between foreign
aid, levels of schooling and democracy for Pakistan using the ARDL
cointegration approach. The results of study provide strong evidence
for fairly robust long run as well as short run relationships among
these variables for the period 1973-2008. The results state that
foreign aid and primary school enrollments have negative impact on
democracy index and high school enrollments have positive impact
on democracy index in Pakistan. The study suggests for promotion of
education levels and relies on local resources instead of foreign aid
for a good quality of political institutions in Pakistan.
Abstract: Lectins have a good scope in current clinical
microbiology research. In the present study evaluated the
antimicrobial activities of a D-galactose binding lectin (PnL) was
purified from the annelid, Perinereis nuntia (polychaeta) by affinity
chromatography. The molecular mass of the lectin was determined to
be 32 kDa as a single polypeptide by SDS-PAGE under both reducing
and non-reducing conditions. The hemagglutinating activity of the
PnL showed against trypsinized and glutaraldehyde-fixed human
erythrocytes was specifically inhibited by D-Gal, GalNAc,
Galβ1-4Glc and Galα1-6Glc. PnL was evaluated for in vitro
antibacterial screening studies against 11 gram-positive and
gram-negative microorganisms. From the screening results, it was
revealed that PnL exhibited significant antibacterial activity against
gram-positive bacteria. Bacillus megaterium showed the highest
growth inhibition by the lectin (250 μg/disc). However, PnL did not
inhibit the growth of gram-negative bacteria such as Vibrio cholerae
and Pseudomonas sp. PnL was also examined for in vitro antifungal
activity against six fungal phytopathogens. PnL (100 μg/mL) inhibited
the mycelial growth of Alternaria alternata (24.4%). These results
indicate that future findings of lectin applications obtained from
annelids may be of importance to life sciences.
Abstract: The purpose of this paper is to conceptualize a futureoriented
human work environment and organizational activity in
deep mines that entails a vision of good and safe workplace. Futureoriented
technological challenges and mental images required for
modern work organization design were appraised. It is argued that an
intelligent-deep-mine covering the entire value chain, including
environmental issues and with work organization that supports good
working and social conditions towards increased human productivity
could be designed. With such intelligent system and work
organization in place, the mining industry could be seen as a place
where cooperation, skills development and gender equality are key
components. By this perspective, both the youth and women might
view mining activity as an attractive job and the work environment
as a safe, and this could go a long way in breaking the unequal
gender balance that exists in most mines today.
Abstract: Advancements in the field of artificial intelligence
(AI) made during this decade have forever changed the way we look
at automating spacecraft subsystems including the electrical power
system. AI have been used to solve complicated practical problems
in various areas and are becoming more and more popular nowadays.
In this paper, a mathematical modeling and MATLAB–SIMULINK
model for the different components of the spacecraft power system is
presented. Also, a control system, which includes either the Neural
Network Controller (NNC) or the Fuzzy Logic Controller (FLC) is
developed for achieving the coordination between the components of
spacecraft power system as well as control the energy flows. The
performance of the spacecraft power system is evaluated by
comparing two control systems using the NNC and the FLC.
Abstract: The composition, vapour pressure, and heat capacity
of nine biodiesel fuels from different sources were measured. The
vapour pressure of the biodiesel fuels is modeled assuming an ideal
liquid phase of the fatty acid methyl esters constituting the fuel. New
methodologies to calculate the vapour pressure and ideal gas and
liquid heat capacities of the biodiesel fuel constituents are proposed.
Two alternative optimization scenarios are evaluated: 1) vapour
pressure only; 2) vapour pressure constrained with liquid heat
capacity. Without physical constraints, significant errors in liquid
heat capacity predictions were found whereas the constrained
correlation accurately fit both vapour pressure and liquid heat
capacity.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.
Abstract: The use of externally bonded Carbon Fiber
Reinforced Polymer (CFRP) reinforcement has proven to be an
effective technique to strengthen steel structures. An experimental
study on CFRP bonded steel plate with double strap joint has been
conducted and specimens are tested under tensile loadings. An
empirical model has been developed using stress-based approach to
predict ultimate capacity of the CFRP bonded steel structure. The
results from the model are comparable with the experimental result
with a reasonable accuracy.
Abstract: In this paper, The T-G-action topology on a set acted
on by a fuzzy T-neighborhood (T-neighborhood, for short) group is
defined as a final T-neighborhood topology with respect to a set of
maps. We mainly prove that this topology is a T-regular Tneighborhood
topology.
Abstract: The present study has been taken to explore the
screening of in vitro antimicrobial activities of D-galactose-binding
sponge lectin (HOL-30). HOL-30 was purified from the marine
demosponge Halichondria okadai by affinity chromatography. The
molecular mass of the lectin was determined to be 30 kDa with a
single polypeptide by SDS-PAGE under non-reducing and reducing
conditions. HOL-30 agglutinated trypsinized and glutaraldehydefixed
rabbit and human erythrocytes with preference for type O
erythrocytes. The lectin was subjected to evaluation for inhibition of
microbial growth by the disc diffusion method against eleven human
pathogenic gram-positive and gram-negative bacteria. The lectin
exhibited strong antibacterial activity against gram-positive bacteria,
such as Bacillus megaterium and Bacillus subtilis. However, it did
not affect against gram-negative bacteria such as Salmonella typhi
and Escherichia coli. The largest zone of inhibition was recorded of
Bacillus megaterium (12 in diameter) and Bacillus subtilis (10 mm in
diameter) at a concentration of the lectin (250 μg/disc). On the other
hand, the antifungal activity of the lectin was investigated against six
phytopathogenic fungi based on food poisoning technique. The lectin
has shown maximum inhibition (22.83%) of mycelial growth of
Botrydiplodia theobromae at a concentration of 100 μg/mL media.
These findings indicate that the lectin may be of importance to
clinical microbiology and have therapeutic applications.