Abstract: Dynamics of a vapour bubble generated due to a high local energy input near a circular thin bronze plate in the absence of the buoyancy forces is numerically investigated in this paper. The bubble is generated near a thin bronze plate and during the growth and collapse of the bubble, it deforms the nearby plate. The Boundary Integral Equation Method is employed for numerical simulation of the problem. The fluid is assumed to be incompressible, irrotational and inviscid and the surface tension on the bubble boundary is neglected. Therefore the fluid flow around the vapour bubble can be assumed as a potential flow. Furthermore, the thin bronze plate is assumed to have perfectly plastic behaviour. Results show that the displacement of the circular thin bronze plate has considerable effect on the dynamics of its nearby vapour bubble. It is found that by decreasing the thickness of the thin bronze plate, the growth and collapse rate of the bubble becomes higher and consequently the lifetime of the bubble becomes shorter.
Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: We theoretically investigate the effects of frequency
detuning and injection power on the nonlinear dynamics of DFB
lasers under dual external optical injection.
Abstract: Recent developments in Soft computing techniques,
power electronic switches and low-cost computational hardware have
made it possible to design and implement sophisticated control
strategies for sensorless speed control of AC motor drives. Such an
attempt has been made in this work, for Sensorless Speed Control of
Induction Motor (IM) by means of Direct Torque Fuzzy Control
(DTFC), PI-type fuzzy speed regulator and MRAS speed estimator
strategy, which is absolutely nonlinear in its nature. Direct torque
control is known to produce quick and robust response in AC drive
system. However, during steady state, torque, flux and current ripple
occurs. So, the performance of conventional DTC with PI speed
regulator can be improved by implementing fuzzy logic techniques.
Certain important issues in design including the space vector
modulated (SVM) 3-Ф voltage source inverter, DTFC design,
generation of reference torque using PI-type fuzzy speed regulator
and sensor less speed estimator have been resolved. The proposed
scheme is validated through extensive numerical simulations on
MATLAB. The simulated results indicate the sensor less speed
control of IM with DTFC and PI-type fuzzy speed regulator provides
satisfactory high dynamic and static performance compare to
conventional DTC with PI speed regulator.
Abstract: The compression-absorption heat pump (C-A HP), one
of the promising heat recovery equipments that make process hot
water using low temperature heat of wastewater, was evaluated by
computer simulation. A simulation program was developed based on
the continuity and the first and second laws of thermodynamics. Both
the absorber and desorber were modeled using UA-LMTD method. In
order to prevent an unfeasible temperature profile and to reduce
calculation errors from the curved temperature profile of a mixture,
heat loads were divided into lots of segments. A single-stage
compressor was considered. A compressor cooling load was also
taken into account. An isentropic efficiency was computed from the
map data. Simulation conditions were given based on the system
consisting of ordinarily designed components. The simulation results
show that most of the total entropy generation occurs during the
compression and cooling process, thus suggesting the possibility that
system performance can be enhanced if a rectifier is introduced.
Abstract: In this paper we propose a Multiple Description Image Coding(MDIC) scheme to generate two compressed and balanced rates descriptions in the wavelet domain (Daubechies biorthogonal (9, 7) wavelet) using pairwise correlating transform optimal and application method for Generalized Multiple Description Coding (GMDC) to image coding in the wavelet domain. The GMDC produces statistically correlated streams such that lost streams can be estimated from the received data. Our performance test shown that the proposed method gives more improvement and good quality of the reconstructed image when the wavelet coefficients are normalized by Gaussian Scale Mixture (GSM) model then the Gaussian one ,.
Abstract: The increasing demand for sufficient and clean
energy forces industrial and service companies to align their strategies towards efficient consumption. This trend refers also to the
residential building sector. There, large amounts of energy consumption are caused by house and facility heating. Many of the
operated hot water heating systems lack hydraulic balanced working
conditions for heat distribution and –transmission and lead to
inefficient heating. Through hydraulic balancing of heating systems,
significant energy savings for primary and secondary energy can be
achieved. This paper addresses the use of KNX-technology (Smart
Buildings) in residential buildings to ensure a dynamic adaption of
hydraulic system's performance, in order to increase the heating
system's efficiency. In this paper, the procedure of heating system
segmentation into hydraulically independent units (meshes) is
presented. Within these meshes, the heating valve are addressed and
controlled by a central facility server. Feasibility criteria towards
such drivers will be named. The dynamic hydraulic balance is
achieved by positioning these valves according to heating loads, that
are generated from the temperature settings in the corresponding
rooms. The energetic advantages of single room heating control
procedures, based on the application FacilityManager, is presented.
Abstract: Stream Control Transmission Protocol (SCTP) has been
proposed to provide reliable transport of real-time communications.
Due to its attractive features, such as multi-streaming and multihoming,
the SCTP is often expected to be an alternative protocol
for TCP and UDP. In the original SCTP standard, the secondary path
is mainly regarded as a redundancy. Recently, most of researches
have focused on extending the SCTP to enable a host to send its
packets to a destination over multiple paths simultaneously. In order
to transfer packets concurrently over the multiple paths, the SCTP
should be well designed to avoid unnecessary fast retransmission
and the mis-estimation of congestion window size through the paths.
Therefore, we propose an Enhanced Cooperative ACK SCTP (ECASCTP)
to improve the path recovery efficiency of multi-homed host
which is under concurrent multiple transfer mode. We evaluated the
performance of our proposed scheme using ns-2 simulation in terms
of cwnd variation, path recovery time, and goodput. Our scheme
provides better performance in lossy and path asymmetric networks.
Abstract: The photochemical and photo-Fenton oxidation of 1,3-dichloro-2-propanol was performed in a batch reactor, at room temperature, using UV radiation, H2O2 as oxidant, and Fenton-s reagent. The effect of the oxidative agent-s initial concentration was investigated as well as the effect of the initial concentration of Fe(II) by following the target compound degradation, the total organic carbon removal and the chloride ion production. Also, from the kinetic analysis conducted and proposed reaction scheme it was deduced that the addition of Fe(II) significantly increases the production and the further oxidation of the chlorinated intermediates.
Abstract: A new dual-fluid concept was studied that could eventually find application for cold-gas propulsion for small space satellites or other constant flow applications. In basic form, the concept uses two different refrigerant working fluids, each having a different saturation vapor pressure. The higher vapor pressure refrigerant remains in the saturation phase and is used to pressurize the lower saturation vapor pressure fluid (the propellant) which remains in the compressed liquid phase. A demonstration thruster concept based on this principle was designed and built to study its operating characteristics. An automotive-type electronic fuel injector was used to meter and deliver the propellant. Ejected propellant mass and momentum were measured for several combinations of refrigerants and hydrocarbon fluids. The thruster has the advantage of delivering relatively large total impulse at low tank pressure within a small volume.
Abstract: In the present investigation, H13 tool steel has been
deposited on copper alloy substrate using both CO2 and diode laser.
A detailed parametric analysis has been carried out in order to find
out optimum processing zone for coating defect free H13 tool steel
on copper alloy substrate. Followed by parametric optimization, the
microstructure and microhardness of the deposited clads have been
evaluated. SEM micrographs revealed dendritic microstructure in
both clads. However, the microhardness of CO2 laser deposited clad
was much higher compared to diode laser deposited clad.
Abstract: This paper aims to initiate an analytical account of the
issues of compliance with economy condition for incentive pay
system application in an enterprise. Economy is considered one of the
conditions for effective incentive pay system application another
condition being the achievement of desired efficiency level of the
incentive pay system application. Bonus pay system is discussed as
an example.
Abstract: Covering-based rough sets is an extension of rough
sets and it is based on a covering instead of a partition of the
universe. Therefore it is more powerful in describing some practical
problems than rough sets. However, by extending the rough sets,
covering-based rough sets can increase the roughness of each model
in recognizing objects. How to obtain better approximations from
the models of a covering-based rough sets is an important issue.
In this paper, two concepts, determinate elements and indeterminate
elements in a universe, are proposed and given precise definitions
respectively. This research makes a reasonable refinement of the
covering-element from a new viewpoint. And the refinement may
generate better approximations of covering-based rough sets models.
To prove the theory above, it is applied to eight major coveringbased
rough sets models which are adapted from other literature.
The result is, in all these models, the lower approximation increases
effectively. Correspondingly, in all models, the upper approximation
decreases with exceptions of two models in some special situations.
Therefore, the roughness of recognizing objects is reduced. This
research provides a new approach to the study and application of
covering-based rough sets.
Abstract: In this work, are discussed two formulations of the boundary element method - BEM to perform linear bending analysis of plates reinforced by beams. Both formulations are based on the Kirchhoff's hypothesis and they are obtained from the reciprocity theorem applied to zoned plates, where each sub-region defines a beam or a slab. In the first model the problem values are defined along the interfaces and the external boundary. Then, in order to reduce the number of degrees of freedom kinematics hypothesis are assumed along the beam cross section, leading to a second formulation where the collocation points are defined along the beam skeleton, instead of being placed on interfaces. On these formulations no approximation of the generalized forces along the interface is required. Moreover, compatibility and equilibrium conditions along the interface are automatically imposed by the integral equation. Thus, these formulations require less approximation and the total number of the degree s of freedom is reduced. In the numerical examples are discussed the differences between these two BEM formulations, comparing as well the results to a well-known finite element code.
Abstract: With the intention of screening for heavy metal
tolerance, a number of bacteria were isolated and characterized from
a pristine soil. Two Gram positive isolates were identified as
Paenibacillus sp. and Bacillus thuringeinsis. Tolerance of Cd2+, Cu2+
and Zn2+ by these bacteria was studied and found that both bacteria
were highly sensitive to Cu2+ compared to other two metals. Both
bacteria showed the same pattern of metal tolerance in the order Zn+
> Cd2+ > Cu2+. When the metal tolerance in both bacteria was
compared, Paenibacillus sp. showed the highest sensitivity to Cu2+
where as B. thuringiensis showed highest sensitivity to Cd2+ and Zn2+
.These findings revealed the potential of Paenibacillus sp. in
developing a biosensor to detect Cu2+ in environmental samples.
Abstract: Little research has examined working memory
capacity (WMC) in signed language interpreters and deaf signers.
This paper presents the findings of a study that investigated WMC in
professional Australian Sign Language (Auslan)/English interpreters
and deaf signers. Thirty-one professional Auslan/English interpreters
(14 hearing native signers and 17 hearing non-native signers)
completed an English listening span task and then an Auslan working
memory span task, which tested their English WMC and their Auslan
WMC, respectively. Moreover, 26 deaf signers (6 deaf native signers
and 20 deaf non-native signers) completed the Auslan working
memory span task. The results revealed a non-significant difference
between the hearing native signers and the hearing non-native signers
in their English WMC, and a non-significant difference between the
hearing native signers and the hearing non-native signers in their
Auslan WMC. Moreover, the results yielded a non-significant
difference between the hearing native signers- English WMC and
their Auslan WMC, and a non-significant difference between the
hearing non-native signers- English WMC and their Auslan WMC.
Furthermore, a non-significant difference was found between the deaf
native signers and the deaf non-native signers in their Auslan WMC.
Abstract: The purpose of this paper is to study Database Models
to use them efficiently in E-commerce websites. In this paper we are
going to find a method which can save and retrieve information in Ecommerce
websites. Thus, semantic web applications can work with,
and we are also going to study different technologies of E-commerce
databases and we know that one of the most important deficits in
semantic web is the shortage of semantic data, since most of the
information is still stored in relational databases, we present an
approach to map legacy data stored in relational databases into the
Semantic Web using virtually any modern RDF query language, as
long as it is closed within RDF. To achieve this goal we study XML
structures for relational data bases of old websites and eventually we
will come up one level over XML and look for a map from relational
model (RDM) to RDF. Noting that a large number of semantic webs
get advantage of relational model, opening the ways which can be
converted to XML and RDF in modern systems (semantic web) is
important.
Abstract: Sweet cherries (Prunus avium L.) contain various
phenolic compounds which contribute to total antioxidant activity.
Total polyphenols, tannins, flavonoids and anthocyanins, and
antioxidant capacity in a fruits of a number of selected sweet cherry
genotypes were investigated. Total polyphenols content ranged from
4.12 to 8.34 mg gallic acid equivantents/g dry fruit weight and total
tannins content ranged from 0.19 to 1.95 mg gallic acid equivalent/g
dry fruit weight. Total flavonoids were within the range 0.42-1.56 mg
of rutin equivalents/g dry fruit weight and total anthocyanins content
were between 0.35 and 0.69 mg cyanidin 3-glucoside equivalent/ g
dry fruit weight. Although sweet cherry fruits are a significant source
of different phenolic compounds, antioxidant activity of sweet
cherries is not related only with the total polyphenolics, flavonoids or
anthocyanins.
Abstract: Microarray data profiles gene expression on a whole
genome scale, therefore, it provides a good way to study associations
between gene expression and occurrence or progression of cancer.
More and more researchers realized that microarray data is helpful
to predict cancer sample. However, the high dimension of gene
expressions is much larger than the sample size, which makes this
task very difficult. Therefore, how to identify the significant genes
causing cancer becomes emergency and also a hot and hard research
topic. Many feature selection algorithms have been proposed in
the past focusing on improving cancer predictive accuracy at the
expense of ignoring the correlations between the features. In this
work, a novel framework (named by SGS) is presented for stable gene
selection and efficient cancer prediction . The proposed framework
first performs clustering algorithm to find the gene groups where
genes in each group have higher correlation coefficient, and then
selects the significant genes in each group with Bayesian Lasso and
important gene groups with group Lasso, and finally builds prediction
model based on the shrinkage gene space with efficient classification
algorithm (such as, SVM, 1NN, Regression and etc.). Experiment
results on real world data show that the proposed framework often
outperforms the existing feature selection and prediction methods,
say SAM, IG and Lasso-type prediction model.