Abstract: Occurrence of a multiple-points fault in machine operations could result in exhibiting complex fault signatures, which could result in lowering fault diagnosis accuracy. In this study, a multiple-points defect model (MPDM) is proposed which can simulate fault signature-s dynamics for n-points bearing faults. Furthermore, this study identifies that in case of multiple-points fault in the rotary machine, the location of the dominant component of defect frequency shifts depending upon the relative location of the fault points which could mislead the fault diagnostic model to inaccurate detections. Analytical and experimental results are presented to characterize and validate the variation in the dominant component of defect frequency. Based on envelop detection analysis, a modification is recommended in the existing fault diagnostic models to consider the multiples of defect frequency rather than only considering the frequency spectrum at the defect frequency in order to incorporate the impact of multiple points fault.
Abstract: The state and stability of hemoglobin adsorbed on the
glass surface was investigated using slab optical waveguide (SOWG)
spectroscopy. The peak position of the absorption band of hemoglobin
adsorbed on the glass surface was same as that of the hemoglobin in
solution. This result suggests that no significant denaturation occurred
by adsorption. The adsorption of hemoglobin is relatively strong that
the hemoglobin molecules even remained adsorbed after rinsing the
cell with buffer solution. The peak shift caused by the reduction of
adsorbed hemoglobin was also observed.
Abstract: A new approach has been used for optimized design of multipliers based upon the concepts of Vedic mathematics. The design has been targeted to state-of-the art field-programmable gate arrays (FPGAs). The multiplier generates partial products using Vedic mathematics method by employing basic 4x4 multipliers designed by exploiting 6-input LUTs and multiplexers in the same slices resulting in drastic reduction in area. The multiplier is realized on Xilinx FPGAs using devices Virtex-5 and Virtex-6.Carry Chain Adder was employed to obtain final products. The performance of the proposed multiplier was examined and compared to well-known multipliers such as Booth, Carry Save, Carry ripple, and array multipliers. It is demonstrated that the proposed multiplier is superior in terms of speed as well as power consumption.
Abstract: In this paper Lattice Boltzmann simulation of
turbulent natural convection with large-eddy simulations (LES) in a
square cavity which is filled by water has been investigated. The
present results are validated by finds of other investigations which
have been done with different numerical methods. Calculations were
performed for high Rayleigh numbers of Ra=108 and 109. The results
confirm that this method is in acceptable agreement with other
verifications of such a flow. In this investigation is tried to present
Large-eddy turbulence flow model by Lattice Boltzmann Method
(LBM) with a clear and simple statement. Effects of increase in
Rayleigh number are displayed on streamlines, isotherm counters and
average Nusselt number. Result shows that the average Nusselt
number enhances with growth of the Rayleigh numbers.
Abstract: The future of business intelligence (BI) is to integrate
intelligence into operational systems that works in real-time
analyzing small chunks of data based on requirements on continuous
basis. This is moving away from traditional approach of doing
analysis on ad-hoc basis or sporadically in passive and off-line mode
analyzing huge amount data. Various AI techniques such as expert
systems, case-based reasoning, neural-networks play important role
in building business intelligent systems. Since BI involves various
tasks and models various types of problems, hybrid intelligent
techniques can be better choice. Intelligent systems accessible
through web services make it easier to integrate them into existing
operational systems to add intelligence in every business processes.
These can be built to be invoked in modular and distributed way to
work in real time. Functionality of such systems can be extended to
get external inputs compatible with formats like RSS. In this paper,
we describe a framework that use effective combinations of these
techniques, accessible through web services and work in real-time.
We have successfully developed various prototype systems and done
few commercial deployments in the area of personalization and
recommendation on mobile and websites.
Abstract: This work presents the first results from the long-term laboratory experiment dealing with impact of drought on soil properties. Three groups of the treatment (A, B and C) with different regime of irrigation were prepared. The soil water content was maintained at 70 % of soil water holding capacity in group A, at 40 % in group B. In group C, soil water regime was maintained in the range of wilting point. Each group of the experiment was divided into three variants (A1 = B1, C1; A2 = B2, C2 etc.) with three repetitions: Variants A1 (B1, C1) were a controls without addition of another fertilizer. Variants A2 (B2, C2) were fertilized with mineral nitrogen fertilizer DAM 390 (0.140 Mg of N per ha) and variants A3 (B3, C3) contained 45 g of Cp per a pot.
The significant differences (ANOVA, P
Abstract: In this paper we would like to introduce some of the
best practices of using semantic markup and its significance in the
success of web applications. Search engines are one of the best ways
to reach potential customers and are some of the main indicators of
web sites' fruitfulness. We will introduce the most important
semantic vocabularies which are used by Google and Yahoo.
Afterwards, we will explain the process of semantic markup
implementation and its significance for search engines and other
semantic markup consumers. We will describe techniques for slow
conceiving RDFa markup to our web application for collecting Call
for papers (CFP) announcements.
Abstract: Numerical studies on race car aerodynamics at wing
in ground effect have been carried out using a steady 3d, double
precision, pressure-based, and standard k-epsilon turbulence model.
Through various parametric analytical studies we have observed that
at a particular speed and ground clearance of the wings a favorable
negative lift was found high at a particular angle of attack for all the
physical models considered in this paper. The fact is that if the
ground clearance height to chord length (h/c) is too small, the
developing boundary layers from either side (the ground and the
lower surface of the wing) can interact, leading to an altered variation
of the aerodynamic characteristics at wing in ground effect. Therefore
a suitable ground clearance must be predicted throughout the racing
for a better performance of the race car, which obviously depends
upon the coupled effects of the topography, wing orientation with
respect to the ground, the incoming flow features and/or the race car
speed. We have concluded that for the design of high performance
and high speed race cars the adjustable wings capable to alter the
ground clearance and the angles of attack is the best design option for
any race car for racing safely with variable speeds.
Abstract: We study different types of aggregation operators such
as the ordered weighted averaging (OWA) operator and the
generalized OWA (GOWA) operator. We analyze the use of OWA
operators in the Minkowski distance. We will call these new distance
aggregation operator the Minkowski ordered weighted averaging
distance (MOWAD) operator. We give a general overview of this
type of generalization and study some of their main properties. We
also analyze a wide range of particular cases found in this
generalization such as the ordered weighted averaging distance
(OWAD) operator, the Euclidean ordered weighted averaging
distance (EOWAD) operator, the normalized Minkowski distance,
etc. Finally, we give an illustrative example of the new approach
where we can see the different results obtained by using different
aggregation operators.
Abstract: With the long-term objective of Critical Heat Flux (CHF) prediction, a Direct Numerical Simulation (DNS) framework for simulation of subcooled and saturated nucleate pool boiling is developed. One case of saturated, and three cases of subcooled boiling at different subcooling levels are simulated. Grid refinement study is also reported. Both boiling and condensation phenomena can be computed simultaneously in the proposed numerical framework. Computed bubble detachment diameters of the saturated nucleate pool boiling cases agree well with the experiment. The flow structures around the growing bubble are presented and the accompanying physics is described. The relation between heat flux evolution from the heated wall and the bubble growth is studied, along with investigations of temperature distribution and flow field evolutions.
Abstract: We present a method for the selection of students
in interdisciplinary studies based on the hybrid averaging
operator. We assume that the available information given in
the problem is uncertain so it is necessary to use interval
numbers. Therefore, we suggest a new type of hybrid
aggregation called uncertain induced generalized hybrid
averaging (UIGHA) operator. It is an aggregation operator
that considers the weighted average (WA) and the ordered
weighted averaging (OWA) operator in the same formulation.
Therefore, we are able to consider the degree of optimism of
the decision maker and grades of importance in the same
approach. By using interval numbers, we are able to represent
the information considering the best and worst possible results
so the decision maker gets a more complete view of the
decision problem. We develop an illustrative example of the
proposed scheme in the selection of students in
interdisciplinary studies. We see that with the use of the
UIGHA operator we get a more complete representation of the
selection problem. Then, the decision maker is able to
consider a wide range of alternatives depending on his
interests. We also show other potential applications that could
be used by using the UIGHA operator in educational problems
about selection of different types of resources such as
students, professors, etc.
Abstract: In this paper, an adaptive polarized Multiple-Input
Multiple-Output (MIMO) Multicarrier Spread Spectrum Code Division Multiple Access (MC-SS-CDMA) system is designed for downlink mobile communications. The proposed system will be
examined in Frequency Division Duplex (FDD) mode for both macro urban and suburban environments. For the same transmission
bandwidth, a performance comparison between both nonoverlapped and orthogonal Frequency Division Multiplexing (FDM) schemes will be presented. Also, the proposed system will be compared with
both the closed loop vertical MIMO MC-SS-CDMA system and the
synchronous vertical STBC-MIMO MC-SS-CDMA system. As will
be shown, the proposed system introduces a significant performance
gain as well as reducing the spatial dimensions of the MIMO system
and simplifying the receiver implementation. The effect of the
polarization diversity characteristics on the BER performance will be
discussed. Also, the impact of excluding the cross-polarization MCSS-
CDMA blocks in the base station will be investigated. In addition,
the system performance will be evaluated under different Feedback
Information (FBI) rates for slowly-varying channels. Finally, a
performance comparison for vehicular and pedestrian environments
will be presented
Abstract: In this paper, we summarize recent work of the authors on nanocomputing memory devices. We investigate two memory devices, each comprising a charged metallofullerene and carbon nanotubes. The first device involves two open nanotubes of the same radius that are joined by a centrally located nanotube of a smaller radius. A metallofullerene is then enclosed inside the structure. The second device also involves a etallofullerene that is located inside a closed carbon nanotube. Assuming the Lennard-Jones interaction energy and the continuum approximation, for both devices, the metallofullerene has two symmetrically placed equal minimum energy positions. On one side the metallofullerene represents the zero information state and by applying an external electrical field, it can overcome the energy barrier, and pass from one end of the tube to the other, where the metallofullerene then represents the one information state.
Abstract: Since Network-on-Chip (NoC) uses network
interfaces (NIs) to improve the design productivity, by now, there
have been a few papers addressing the design and implementation of a
NI module. However, none of them considered the difference of
address encoding methods between NoC and the traditional
bus-shared architecture. On the basis of this difference, in the paper,
we introduce a transmit mechanism to solve such a problem for global
asynchronous locally synchronous (GALS) NoC. Furthermore, we
give the concrete implementation of the NI module in this transmit
mechanism. Finally, we evaluate its performance and area overhead
by a VHDL-based cycle-accurate RTL model and simulation results
confirm the validity of this address-oriented transmit mechanism.
Abstract: A numerical prediction of flow in a tube bank is reported. The flow regimes considered cover a wide range of Reynolds numbers, which range from 380 to 99000 and which are equivalent to a range of inlet velocities from very low (0.072 m/s) to very high (60 m/s). In this study, calculations were made using the standard k-e model with standard wall function. The drag coefficient, skin friction drag, pressure drag, and pressure distribution around a tube were investigated. As the velocity increased, the drag coefficient decreased until the velocity exceeded 45 m/s, after which it increased. Furthermore, the pressure drag and skin friction drag depend on the velocity.
Abstract: This paper aims to scale up Dye-sensitized Solar Cell
(DSSC) production using a commonly available industrial material –
stainless steel - and industrial plasma equipment. A working DSSC
electrode formed by (1) coating titania nanotube (TiO2 NT) film on
304 stainless steel substrate using a plasma spray technique; then, (2)
filling the nano-pores of the TiO2 NT film using a TiF4 sol-gel method.
A DSSC device consists of an anode absorbed photosensitive dye
(N3), a transparent conductive cathode with platinum (Pt)
nano-catalytic particles adhered to its surface, and an electrolytic
solution sealed between the anode and the transparent conductive
cathode. The photo-current conversion efficiency of the DSSC sample
was tested under an AM 1.5 Solar Simulator. The sample has a short
current (Isc) of 0.83 mA cm-2, open voltage (Voc) of 0.81V, filling
factor (FF) of 0.52, and conversion efficiency (η) of 2.18% on a 0.16
cm2 DSSC work-piece.
Abstract: The research on two-wheels balancing robot has
gained momentum due to their functionality and reliability when
completing certain tasks. This paper presents investigations into the
performance comparison of Linear Quadratic Regulator (LQR) and
PID-PID controllers for a highly nonlinear 2–wheels balancing robot.
The mathematical model of 2-wheels balancing robot that is highly
nonlinear is derived. The final model is then represented in statespace
form and the system suffers from mismatched condition. Two
system responses namely the robot position and robot angular
position are obtained. The performances of the LQR and PID-PID
controllers are examined in terms of input tracking and disturbances
rejection capability. Simulation results of the responses of the
nonlinear 2–wheels balancing robot are presented in time domain. A
comparative assessment of both control schemes to the system
performance is presented and discussed.
Abstract: the present paper, using the technique of differential subordination, we obtain certain results for analytic functions defined by a multiplier transformation in the open unit disc E = { z : IzI < 1}. We claim that our results extend and generalize the existing results in this particular direction
Abstract: Pomegranate and pomegranate juices (PJs) have taken
great attention for their health benefits in the last years. As there is an
increasing concern about potential health benefits of ellagic acid, it is
of great interest to evaluate alterations in ellagic acid concentration of
commercial PJs. The purpose of this study is to analyze total
phenolic, free and total ellagic acid content of six commercial PJs
sold in Turkish markets using HPLC.
The results showed that some commercial PJs had markedly high
total phenolic and ellagic acid content. Total phenolic substances of
commercial PJs range from 796.71 to 4608.91 mg GAE/l. Free
amount of ellagic acid in commercial PJs range from 27.64 to 111.78
mg/l. Samples are hydrolyzed with concentrated HCl at 93oC for 2
and 24 hour and influences of temperature and time parameters on
hydrolization were investigated. Thermal processing for
pasteurization increased ellagic acid via ellagitannins hydrolysis.
Abstract: Technological newness and innovativeness are
important aspects of small firm development, growth and wealth
creation. The contribution of the study to entrepreneurship
personality research and to technology-related research in
entrepreneurship is that the model of the general personality driven
technological development was developed and empirically tested.
Hypotheses relating the big five personality factors (OCEAN:
openness, conscientiousness, extraversion, agreeableness, and
neuroticism) and technological developments were tested by using
multiple regression analysis on survey data from a sample of 160
entrepreneurs from Slovenia. The model reveals two personality
factors, which are predictive of technological developments:
openness (positive impact) and neuroticism (negative impact). In
addition, a positive impact of firm age on technological
developments was found. Other personality factors
(conscientiousness, extraversion and agreeableness) of entrepreneurs
may not be considered important for their firm technological
developments.