Abstract: An experimental and analytical research on shear
buckling of a comparably large polymer composite I-section is
presented. It is known that shear buckling load of a large span
composite beam is difficult to determine experimentally. In order to
sensitively detect shear buckling of the tested I-section, twenty strain
rosettes and eight displacement sensors were applied and attached on
the web and flange surfaces. The tested specimen was a pultruded
composite beam made of vinylester resin, E-glass, carbon fibers and
micro-fillers. Various coupon tests were performed before the shear
buckling test to obtain fundamental material properties of the Isection.
An asymmetric four-point bending loading scheme was
utilized for the shear test. The loading scheme resulted in a high shear
and almost zero moment condition at the center of the web panel. The
shear buckling load was successfully determined after analyzing the
obtained test data from strain rosettes and displacement sensors. An
analytical approach was also performed to verify the experimental
results and to support the discussed experimental program.
Abstract: During the post-Civil War era, the city of Nashville,
Tennessee, had the highest mortality rate in the United States. The
elevated death and disease rates among former slaves were
attributable to lack of quality healthcare. To address the paucity of
healthcare services, Meharry Medical College, an institution with the
mission of educating minority professionals and serving the
underserved population, was established in 1876.
Purpose: The social ecological framework and partial least squares
(PLS) path modeling were used to quantify the impact of
socioeconomic status and adverse health outcome on primary care
professionals serving the disadvantaged community. Thus, the study
results could demonstrate the accomplishment of the College’s
mission of training primary care professionals to serve in underserved
areas.
Methods: Various statistical methods were used to analyze alumni
data from 1975 – 2013. K-means cluster analysis was utilized to
identify individual medical and dental graduates in the cluster groups
of the practice communities (Disadvantaged or Non-disadvantaged
Communities). Discriminant analysis was implemented to verify the
classification accuracy of cluster analysis. The independent t-test was
performed to detect the significant mean differences of respective
clustering and criterion variables. Chi-square test was used to test if
the proportions of primary care and non-primary care specialists are
consistent with those of medical and dental graduates practicing in
the designated community clusters. Finally, the PLS path model was
constructed to explore the construct validity of analytic model by
providing the magnitude effects of socioeconomic status and adverse
health outcome on primary care professionals serving the
disadvantaged community.
Results: Approximately 83% (3,192/3,864) of Meharry Medical
College’s medical and dental graduates from 1975 to 2013 were
practicing in disadvantaged communities. Independent t-test confirmed the content validity of the cluster analysis model. Also, the
PLS path modeling demonstrated that alumni served as primary care
professionals in communities with significantly lower socioeconomic
status and higher adverse health outcome (p < .001). The PLS path
modeling exhibited the meaningful interrelation between primary
care professionals practicing communities and surrounding
environments (socioeconomic statues and adverse health outcome),
which yielded model reliability, validity, and applicability.
Conclusion: This study applied social ecological theory and
analytic modeling approaches to assess the attainment of Meharry
Medical College’s mission of training primary care professionals to
serve in underserved areas, particularly in communities with low
socioeconomic status and high rates of adverse health outcomes. In
summary, the majority of medical and dental graduates from Meharry
Medical College provided primary care services to disadvantaged
communities with low socioeconomic status and high adverse health
outcome, which demonstrated that Meharry Medical College has
fulfilled its mission. The high reliability, validity, and applicability of
this model imply that it could be replicated for comparable
universities and colleges elsewhere.
Abstract: Introduction: There are multiple social, individual and
cultural factors that influence an individual’s decision to adopt family
planning methods especially among non-users in patriarchal societies
like Pakistan. Non-users, if targeted efficiently, can contribute
significantly to country’s CPR. A research study showed that nonusers
if convinced to adopt lactational amenorrhea method can shift
to long term methods in future. Research shows that if non users are
targeted efficiently a 59% reduction in unintended pregnancies in
Saharan Africa and South-Central and South-East Asia is anticipated.
Methods: We did secondary data analysis on Pakistan
Demographic Heath Survey (2012-13) dataset. Use of contraception
(never-use/ever-use) was the outcome variable. At univariate level
Chi-square/Fisher Exact test was used to assess relationship of
baseline covariates with contraception use. Then variables to be
incorporated in the model were checked for multicollinearity,
confounding and interaction. Then binary logistic regression (with an
urban-rural stratification) was done to find relationship between
contraception use and baseline demographic and social variables.
Results: The multivariate analyses of the study showed that
younger women (≤ 29 years)were more prone to be never users as
compared to those who were >30 years and this trend was seen in
urban areas (AOR 1.92, CI 1.453-2.536) as well as rural areas (AOR
1.809, CI 1.421-2.303). While looking at regional variation, women
from urban Sindh (AOR 1.548, CI 1.142-2.099) and urban
Balochistan (AOR 2.403, CI 1.504-3.839) had more never users as
compared to other urban regions. Women in the rich wealth quintile
were more never users and this was seen both in urban and rural
localities (urban (AOR 1.106 CI .753-1.624); rural areas (AOR 1.162,
CI .887-1.524)) even though these were not statistically significant.
Women idealizing more children (>4) are more never users as
compared to those idealizing less children in both urban (AOR 1.854,
CI 1.275-2.697) and rural areas (AOR 2.101, CI 1.514-2.916).
Women who never lost a pregnancy were more inclined to be nonusers
in rural areas (AOR 1.394, CI 1.127-1.723) .Women familiar
with only traditional or no method had more never users in rural areas
(AOR 1.717, CI 1.127-1.723) but in urban areas it wasn’t significant.
Women unaware of Lady Health Worker’s presence in their area
were more never users especially in rural areas (AOR 1.276, CI
1.014-1.607). Women who did not visit any care provider were more
never users (urban (AOR 11.738, CI 9.112-15.121) rural areas (AOR
7.832, CI 6.243-9.826)).
Discussion/Conclusion: This study concluded that government,
policy makers and private sector family planning programs should
focus on the untapped pool of never users (younger women from underserved provinces, in higher wealth quintiles, who desire more
children.). We need to make sure to cover catchment areas where
there are less LHWs and less providers as ignorance to modern
methods and never been visited by an LHW are important
determinants of never use. This all is in sync with previous literate
from similar developing countries.
Abstract: The effect of N2 pretreatment on the catalytic activity
of tungsten-based catalysts was investigated in the metathesis of
ethylene and trans-2-butene at 450oC and atmospheric pressure. The
presence of tungsten active species was confirmed by UV-Vis and
Raman spectroscopy. Compared to the WO3-based catalysts treated
in air, higher amount of WO4 2-tetrahedral species and lower amount
of WO3 crystalline species were observed on the N2-treated ones.
These contribute to the higher conversion of 2-butene and propylene
selectivity during 10 h time-on-stream. Moreover, N2 treatment led to
lower amount of coke formation as revealed by TPO of the spent
catalysts.
Abstract: The Scheduling and mapping of tasks on a set of
processors is considered as a critical problem in parallel and
distributed computing system. This paper deals with the problem of
dynamic scheduling on a special type of multiprocessor architecture
known as Linear Crossed Cube (LCQ) network. This proposed
multiprocessor is a hybrid network which combines the features of
both linear types of architectures as well as cube based architectures.
Two standard dynamic scheduling schemes namely Minimum
Distance Scheduling (MDS) and Two Round Scheduling (TRS)
schemes are implemented on the LCQ network. Parallel tasks are
mapped and the imbalance of load is evaluated on different set of
processors in LCQ network. The simulations results are evaluated
and effort is made by means of through analysis of the results to
obtain the best solution for the given network in term of load
imbalance left and execution time. The other performance matrices
like speedup and efficiency are also evaluated with the given
dynamic algorithms.
Abstract: Present study is carried out on six lane divided urban
arterial road in Patna and Pune city of India. Both the road having
distinct differences in terms of the vehicle composition and the road
side parking. Arterial road in Patan city has 33% of non-motorized
mode, whereas Pune arterial road dominated by 65% of Two wheeler.
Also road side parking is observed in Patna city. The field studies
using videography techniques are carried out for traffic data
collection. Data are extracted for one minute duration for vehicle
composition, speed variation and flow rate on selected arterial road of
the two cities. Speed flow relationship is developed and capacity is
determine. Equivalency factor in terms of dynamic car unit is
determine to represent the vehicle is single unit. The variation in the
capacity due to side friction, presence of non motorized traffic and
effective utilization of lane width is compared at concluding remarks.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: Due to rapid pressured of population growth, city has
started to lose its old tradition. City becomes congested with
uncomfortably living. Urban renewal refers orderly development of
settlements as well as land redevelopment. For this paper Chittagong
city has been selected as study area. It had a great tradition but it has
been losing its concord. Land use pattern of this place is also
haphazard due to lack of planning intervention. Renewal plan is
needed to ascertain suitable redevelopment and to recommend on
preservation of city heritage structure. The goal of this study is to
prepare a renewal plan using local planning approach. Social impact
methods have been used to achieve this goal. Both primary and
secondary data are used to achieve the goal. This study may find out
a complete solution for healthy living in old Part of city. This study
will help to preserve its tradition and makes urban lives more livable.
Abstract: This study presented to reduce earthquake damage and
emergency rehabilitation of critical structures such as schools, hightech
factories, and hospitals due to strong ground motions associated
with climate changes. Regarding recent trend, a strong earthquake
causes serious damage to critical structures and then the critical
structure might be influenced by sequence aftershocks (or tsunami)
due to fault plane adjustments. Therefore, in order to improve seismic
performance of critical structures, retrofitted or strengthening study
of the structures under aftershocks sequence after emergency
rehabilitation of the structures subjected to strong earthquakes is
widely carried out. Consequently, this study used composite material
for emergency rehabilitation of the structure rather than concrete and
steel materials because of high strength and stiffness, lightweight,
rapid manufacturing, and dynamic performance. Also, this study was
to develop or improve the seismic performance or seismic retrofit of
critical structures subjected to strong ground motions and earthquake
aftershocks, by utilizing GFRP-Corrugated Infill Panels (GCIP).
Abstract: ABC classification is widely used by managers for
inventory control. The classical ABC classification is based on Pareto
principle and according to the criterion of the annual use value only.
Single criterion classification is often insufficient for a closely
inventory control. Multi-criteria inventory classification models have
been proposed by researchers in order to consider other important
criteria. From these models, we will consider a specific model in
order to make a sensitive analysis on the composite score calculated
for each item. In fact, this score, based on a normalized average
between a good and a bad optimized index, can affect the ABC-item
classification. We will focus on items differently assigned to classes
and then propose a classification compromise.
Abstract: This paper shows in detail the mathematical model of
direct and inverse kinematics for a robot manipulator (welding type)
with four degrees of freedom. Using the D-H parameters, screw
theory, numerical, geometric and interpolation methods, the
theoretical and practical values of the position of robot were
determined using an optimized algorithm for inverse kinematics
obtaining the values of the particular joints in order to determine the
virtual paths in a relatively short time.
Abstract: Moringa oleifera is a nutritious vegetable tree with
varieties of potential uses, as almost every part of the Moringa
oleifera tree can be used for food. This study was conducted in Oyo
State, Nigeria, to find out the level of acceptability of Moringa
oleifera diversified products among rural and urban dwellers.
Purposive sampling was used to select two local governments’ areas.
Stratified sampling technique was also used to select one community
each from rural and urban areas while snowball sampling technique
was used to select ten respondents each from the two communities,
making a total number of forty respondents. Data were analyzed
using frequencies, percentages, Chi-square, Pearson Product Moment
Correlation and regression analysis. Result from the study revealed
that majority of the respondents (80%) fell within the age range of
20-49 years and 55% of them were male, 55% were married, 70% of
them were Christians, 80% of them had tertiary education. The result
also showed that 85% were aware of the Moringa plant and (65%) of
them have consumed Moringa oleifera and the perception statements
on the benefits of Moringa oleifera indicated that (52.5%) of the
respondents rated Moringa oleifera to be favorable, most of them had
high acceptability for Moringa egusi soup, Moringa tea, Moringa pap
and yam pottage with Moringa. The result of the hypotheses testing
showed that there is a significant relationship between sex of the
respondents and acceptability of the diversified Moringa oleifera
products (x2=6.465, p = 0.011). There is also a significant
relationship between family size of the respondents level of
acceptability of the Moringa oleifera products (r = 0.327, p = 0.040).
Based on the level of acceptability of Moringa oleifera diversified
products; the plant is of great economic importance to the populace.
Therefore, there should be more public awareness through the media
to enlighten people on the beneficial effects of Moringa oleifera.
Abstract: The advent of social networking technologies has been
met with mixed reactions in academic and corporate circles around
the world. This study explored the influence of social network in
current era, the relation being maintained between the Social
networking site and its user by the extent of use, benefits and latest
technologies. The study followed a descriptive research design
wherein a questionnaire was used as the main research tool. The data
collected was analyzed using SPSS 16. Data was gathered from 1205
users and analyzed in accordance with the objectives of the study.
The analysis of the results seem to suggest that the majority of users
were mainly using Facebook, despite of concerns raised about the
disclosure of personal information on social network sites, users
continue to disclose huge quantity of personal information, they find
that reading privacy policy is time consuming and changes made can
result into improper settings.
Abstract: Recently, there is a lot of interest in the field of under
water optical wireless communication for short range because of
its high bandwidth. But in most of the previous works line of
sight propagation or single scattering of photons only considered.
In practical case this is not applicable because of beam blockage in
underwater and multiple scattering also occurred during the photons
propagation through water. In this paper we consider a non-line
of sight underwater wireless optical communication system with
multiple scattering and examine the performance of the system using
monte carlo simulation. The distribution scattering angle of photons
are modeled by Henyey-Greenstein method. The average bit error
rate is calculated using on-off keying modulation for different water
types.
Abstract: Behavioral aspects of experience such as will power
are rarely subjected to quantitative study owing to the numerous
complexities involved. Will is a phenomenon that has puzzled
humanity for a long time. It is a belief that will power of an individual
affects the success achieved by them in life. It is also thought that a
person endowed with great will power can overcome even the most
crippling setbacks in life while a person with a weak will cannot make
the most of life even the greatest assets. This study is an attempt
to subject the phenomena of will to the test of an artificial neural
network through a computational model. The claim being tested is
that will power of an individual largely determines success achieved
in life. It is proposed that data pertaining to success of individuals
be obtained from an experiment and the phenomenon of will be
incorporated into the model, through data generated recursively using
a relation between will and success characteristic to the model.
An artificial neural network trained using part of the data, could
subsequently be used to make predictions regarding data points in
the rest of the model. The procedure would be tried for different
models and the model where the networks predictions are found to
be in greatest agreement with the data would be selected; and used
for studying the relation between success and will.
Abstract: Present paper describes method of obtaining clay
ceramic foam (CCF) and foam concrete (FC), by direct foaming with
high speed mixer-disperser (HSMD). Three foaming agents (FA) are
compared for the FC and CCF production: SCHÄUMUNGSMITTEL
W 53 FLÜSSIG (Zschimmer & Schwarz Gmbh, Germany), SCF-
1245 (Sika, test sample, Latvia) and FAB-12 (Elade, Latvija). CCF
were obtained at 950, 1000°C, 1150°C and 1150°C firing temperature
and have mechanical compressive strength 1.2, 2.55 and 4.3 MPa and
porosity 79.4, 75.1, 71.6%, respectively. Obtained FC has 6-14 MPa
compressive strength and porosity 44-55%. The goal of this work
was development of a sustainable and durable ceramic cellular
structures using HSMD.
Abstract: The research of juice flavor forecasting has become
more important in China. Due to the fast economic growth in China,
many different kinds of juices have been introduced to the market. If a
beverage company can understand their customers’ preference well,
the juice can be served more attractive. Thus, this study intends to
introducing the basic theory and computing process of grapes juice
flavor forecasting based on support vector regression (SVR). Applying
SVR, BPN, and LR to forecast the flavor of grapes juice in real data
shows that SVR is more suitable and effective at predicting
performance.
Abstract: High pressure turbine (HPT) blades of DV – 2 jet
engines are made from Ni – based superalloy. This alloy was
originally manufactured in the Soviet Union and referred as ŽS6K.
For improving alloy’s high temperature resistance are blades coated
with Al – Si diffusion layer. A regular operation temperature of HPT
blades vary from 705°C to 750°C depending on jet engine regime.
An overcrossing working temperature range causes degradation of
the protective coating as well as base material which microstructure
is formed by the gamma matrix and strengthening phase gamma
prime (forming small particles in the microstructure). Diffusion
processes inside the material during exposition of the material to high
temperatures causes mainly coarsening of the gamma prime particles,
thus decreasing its strengthening effect. Degradation of the Al – Si
coating caused its thickness growth. All the microstructure changes
and coating layer thickness growth results in decreasing of the turbine
blade operation lifetime.
Abstract: Indonesian higher education has experienced
significant changes over the last decade. In 1999, the government
published an overall strategy for decentralisation and enhancement of
local autonomy in many sectors, including (higher) education.
Indonesian higher education reforms have forced universities to
restructure their internal university governance to become more
entrepreneurial. These new types of internal university governance
are likely to affect the institutions’ leadership and management. This
paper discusses the approach and findings of a study on the
managerial leadership styles of deans in Indonesian universities. The
study aims to get a better understanding of styles exhibited by deans
manifested in their behaviours. Using the theories of reasoned action
and planned behaviour, in combination with the competing values
framework, a large-scale survey was conducted to gather information
on the deans’ behaviours, attitudes, subjective norms, and perceived
behavioural control. Based on the responses of a sample of 218
deans, the study identifies a number of leadership styles: the Master,
the Competitive Consultant, the Consensual Goal-Setter, the Focused
Team Captain, and the Informed Trust-Builder style. The study
demonstrates that attitudes are the primary determinant of the styles
that were found. Perceived behavioural control is a factor that
explains some managerial leadership styles. By understanding the
attitudes of deans in Indonesian universities, and their leadership
styles, universities can strengthen their management and governance,
and thus improve their effectiveness.
Abstract: DC motors have been widely used in the past
centuries which are proudly known as the workhorse of industrial
systems until the invention of the AC induction motors which makes
a huge revolution in industries. Since then, the use of DC machines
has been decreased due to enormous factors such as reliability,
robustness and complexity but it lost its fame due to the losses. In this
paper a new methodology is proposed to construct a DC motor
through the simulation in LabVIEW to get an idea about its real time
performances, if a change in parameter might have bigger
improvement in losses and reliability.