Abstract: Non contact evaluation of the thickness of paint
coatings can be attempted by different destructive and nondestructive
methods such as cross-section microscopy, gravimetric mass
measurement, magnetic gauges, Eddy current, ultrasound or
terahertz. Infrared thermography is a nondestructive and non-invasive
method that can be envisaged as a useful tool to measure the surface
thickness variations by analyzing the temperature response. In this
paper, the thermal quadrupole method for two layered samples heated
up with a pulsed excitation is firstly used. By analyzing the thermal
responses as a function of thermal properties and thicknesses of both
layers, optimal parameters for the excitation source can be identified.
Simulations show that a pulsed excitation with duration of ten
milliseconds allows obtaining a substrate-independent thermal
response. Based on this result, an experimental setup consisting of a
near-infrared laser diode and an Infrared camera was next used to
evaluate the variation of paint coating thickness between 60 μm and
130 μm on two samples. Results show that the parameters extracted
for thermal images are correlated with the estimated thicknesses by
the Eddy current methods. The laser pulsed thermography is thus an
interesting alternative nondestructive method that can be moreover
used for nonconductive substrates.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).
Abstract: Characterization of the engineering behavior of
unsaturated soil is dependent on the soil-water characteristic curve
(SWCC), a graphical representation of the relationship between water
content or degree of saturation and soil suction. A reasonable
description of the SWCC is thus important for the accurate prediction
of unsaturated soil parameters. The measurement procedures for
determining the SWCC, however, are difficult, expensive, and timeconsuming.
During the past few decades, researchers have laid a
major focus on developing empirical equations for predicting the
SWCC, with a large number of empirical models suggested. One of
the most crucial questions is how precisely existing equations can
represent the SWCC. As different models have different ranges of
capability, it is essential to evaluate the precision of the SWCC
models used for each particular soil type for better SWCC estimation.
It is expected that better estimation of SWCC would be achieved via
a thorough statistical analysis of its distribution within a particular
soil class. With this in view, a statistical analysis was conducted in
order to evaluate the reliability of the SWCC prediction models
against laboratory measurement. Optimization techniques were used
to obtain the best-fit of the model parameters in four forms of SWCC
equation, using laboratory data for relatively coarse-textured (i.e.,
sandy) soil. The four most prominent SWCCs were evaluated and
computed for each sample. The result shows that the Brooks and
Corey model is the most consistent in describing the SWCC for sand
soil type. The Brooks and Corey model prediction also exhibit
compatibility with samples ranging from low to high soil water
content in which subjected to the samples that evaluated in this study.
Abstract: The purpose of this work is to optimize a Switched Reluctance Motor (SRM) for an automotive application, specifically for a fully electric car. A new optimization approach is proposed. This unique approach transforms automotive customer requirements into an optimization problem, based on sound knowledge of a SRM theory. The approach combines an analytical and a finite element analysis of the motor to quantify static nonlinear and dynamic performance parameters, as phase currents and motor torque maps, an output power and power losses in order to find the optimal motor as close to the reality as possible, within reasonable time. The new approach yields the optimal motor which is competitive with other types of already proposed motors for automotive applications. This distinctive approach can also be used to optimize other types of electrical motors, when parts specifically related to the SRM are adjusted accordingly.
Abstract: This article investigates technology used by Tshwane residents intended for tourism purposes. The aim is to contribute information for planning and management concerning technology within the tourism sector in the city of Tshwane, South Africa. This study identified the types of tourist related technologies used by the Tshwane residents, be it for business purposes or personal use. The study connected the exploitation of technology for tourism purposes through unpacking the tourism sector as it utilizes technology. Quantitative research methodology was used whereby self-completed questionnaires were chosen as research instruments. The research study carried out a search for knowledge on technology for tourism and the Tshwane residents; however the study revealed that technology has certainly imprinted tourism massively because of its effectiveness and efficiency. Technology has assisted tourism businesses stay abreast of competition with integrated communication technology (ICT) and because of that, SA is on the map as one of the economically performing countries in Africa. Moreover, technology and tourism make a meaningful impact on job creation and Gross Domestic Product (GDP).
Abstract: Microgrids are increasingly being considered to provide electricity for the expanding energy demand in the grid distribution network and grid isolated areas. However, the technical challenges associated with the operation and controls are immense. Management of dynamic power balances, power flow, and network voltage profiles imposes unique challenges in the context of microgrids. Stability of the microgrid during both grid-connected and islanded mode is considered as the major challenge during its operation. Traditional control methods have been employed are based on the assumption of linear loads. For instance the concept of PQ, voltage and frequency control through decoupled PQ are some of very useful when considering linear loads, but they fall short when considering nonlinear loads. The deficiency of traditional control methods of microgrid suggests that more research in the control of microgrids should be done. This research aims at introducing the dq technique concept into decoupled PQ for dynamic load demand control in inverter interfaced DG system operating as isolated LV microgrid. Decoupled PQ in exact mathematical formulation in dq frame is expected to accommodate all variations of the line parameters (resistance and inductance) and to relinquish forced relationship between the DG variables such as power, voltage and frequency in LV microgrids and allow for individual parameter control (frequency and line voltages). This concept is expected to address and achieve accurate control, improve microgrid stability and power quality at all load conditions.
Abstract: The Time-Domain Boundary Element Method (TDBEM)
is a well known numerical technique that handles quite
properly dynamic analyses considering infinite dimension media.
However, when these analyses are also related to nonlinear behavior,
very complex numerical procedures arise considering the TD-BEM,
which may turn its application prohibitive. In order to avoid this
drawback and model nonlinear infinite media, the present work
couples two BEM formulations, aiming to achieve the best of two
worlds. In this context, the regions expected to behave nonlinearly
are discretized by the Domain Boundary Element Method (D-BEM),
which has a simpler mathematical formulation but is unable to deal
with infinite domain analyses; the TD-BEM is employed as in the
sense of an effective non-reflexive boundary. An iterative procedure
is considered for the coupling of the TD-BEM and D-BEM, which is
based on a relaxed renew of the variables at the common interfaces.
Elastoplastic models are focused and different time-steps are allowed
to be considered by each BEM formulation in the coupled analysis.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: A new class of fuzzy closed sets, namely fuzzy weakly closed set in a fuzzy topological space is introduced and it is established that this class of fuzzy closed sets lies between fuzzy closed sets and fuzzy generalized closed sets. Alongwith the study of fundamental results of such closed sets, we define and characterize fuzzy weakly compact space and fuzzy weakly closed space.
Abstract: The values of managers and employees in organizations are phenomena that have captured the interest of researchers at large. Despite this attention, there continues to be a lack of agreement on what values are and how they influence individuals, or how they are constituted in individuals- mind. In this article content-based approach is presented as alternative reference frame for exploring values. In content-based approach human thinking in different contexts is set at the focal point. Differences in valuations can be explained through the information contents of mental representations. In addition to the information contents, attention is devoted to those cognitive processes through which mental representations of values are constructed. Such informational contents are in decisive role for understanding human behavior. By applying content-based analysis to an examination of values as mental representations, it is possible to reach a deeper to the motivational foundation of behaviors, such as decision making in organizational procedures, through understanding the structure and meanings of specific values at play.
Abstract: Calculations of energy efficiency of several AACbased
building envelopes under different climatic conditions are
presented. As thermal insulating materials, expanded polystyrene and
hydrophobic and hydrophilic mineral wools are assumed. The
computations are accomplished using computer code HEMOT
developed at Department of Materials Engineering, Faculty of Civil
Engineering at the Czech Technical University in Prague. The
climatic data of Athens, Kazan, Oslo, Prague and Reykjavík are
obtained using METEONORM software.
Abstract: Large metal and concrete structures suffer by various kinds of deterioration, and accurate prediction of the remaining life is important. This paper informs about two methods for its assessment. One method, suitable for steel bridges and other constructions exposed to fatigue, monitors the loads and damage accumulation using information systems for the operation and the finite element model of the construction. In addition to the operation load, the dead weight of the construction and thermal stresses can be included into the model. The second method is suitable for concrete bridges and other structures, which suffer by carbonatation and other degradation processes, driven by diffusion. The diffusion constant, important for the prediction of future development, can be determined from the depth-profile of pH, obtained by pH measurement at various depths. Comparison with measurements on real objects illustrates the suitability of both methods.
Abstract: One of the aims of the paper is to make a comparison
of experimental results with numerical simulation for a side cooler.
Specifically, it was the amount of air to be delivered by the side
cooler with fans running at 100%. This integral value was measured
and evaluated within the plane parallel to the front side of the side
cooler at a distance of 20mm from the front side. The flow field
extending from the side cooler to the space was also evaluated.
Another objective was to address the contribution of evaluated values
to the increase of data center energy consumption.
Abstract: An experimental study is realized in order to verify the
Mini Heat Pipe (MHP) concept for cooling high power dissipation
electronic components and determines the potential advantages of
constructing mini channels as an integrated part of a flat heat pipe. A
Flat Mini Heat Pipe (FMHP) prototype including a capillary structure
composed of parallel rectangular microchannels is manufactured and
a filling apparatus is developed in order to charge the FMHP. The
heat transfer improvement obtained by comparing the heat pipe
thermal resistance to the heat conduction thermal resistance of a
copper plate having the same dimensions as the tested FMHP is
demonstrated for different heat input flux rates. Moreover, the heat
transfer in the evaporator and condenser sections are analyzed, and
heat transfer laws are proposed. In the theoretical part of this work, a
detailed mathematical model of a FMHP with axial microchannels is
developed in which the fluid flow is considered along with the heat
and mass transfer processes during evaporation and condensation.
The model is based on the equations for the mass, momentum and
energy conservation, which are written for the evaporator, adiabatic,
and condenser zones. The model, which permits to simulate several
shapes of microchannels, can predict the maximum heat transfer
capacity of FMHP, the optimal fluid mass, and the flow and thermal
parameters along the FMHP. The comparison between experimental
and model results shows the good ability of the numerical model to
predict the axial temperature distribution along the FMHP.
Abstract: Corporate social responsibility (CSR) viewpoint have challenged the traditional perception to understand corporations position. Production- and managerial-centred views are expanding towards reference group-centred policies. Consequently, the significance of new kind of knowledge has emerged. In addition to management of the organisation, the idea of CSR emphasises the importance to recognise the value-expectations of operational environment. It is know that management is often well-aware of corporate social responsibilities, but it is less clear how well these high level goals are understood in practical product design and development work. In this study, the apprehension above proved to be real to some degree. While management was very aware of CSR it was less familiar to designers. The outcome shows that it is essential to raise ethical values and issues higher in corporate communication, if it is wished that they materialize also in products.
Abstract: This paper focuses on issues of engagement by staff in professional development related to the delivery of e-learning. The paper reports on findings drawn from a New Zealand research project which is producing a sector-wide framework for professional development in tertiary e-learning. The research findings indicate that staff engaged in e-learning in tertiary institutions is not making the most effective use of the professional development opportunities available to them; rather they seem to gain their knowledge and support from a variety of informal means. This is despite an emphasis on the provision of professional development opportunities by both Government Policies and Institutions themselves. The conclusion drawn from the findings is that institutional approaches to professional development for e-learning do not yet fully reflect the demands and constraints that working in a digital context impose.
Abstract: Wind energy has been shown to be one of the most
viable sources of renewable energy. With current technology, the low
cost of wind energy is competitive with more conventional sources of
energy such as coal. Most blades available for commercial grade
wind turbines incorporate a straight span-wise profile and airfoil
shaped cross sections. These blades are found to be very efficient at
lower wind speeds in comparison to the potential energy that can be
extracted. However as the oncoming wind speed increases the
efficiency of the blades decreases as they approach a stall point. This
paper explores the possibility of increasing the efficiency of the
blades at higher wind speeds while maintaining efficiency at the
lower wind speeds. The design intends to maintain efficiency at
lower wind speeds by selecting the appropriate orientation and size
of the airfoil cross sections based on a low oncoming wind speed and
given constant rotation rate. The blades will be made more efficient
at higher wind speeds by implementing a swept blade profile.
Performance was investigated using the computational fluid
dynamics (CFD).
Abstract: Turbulence studies were made in the wake of a rotating
circular cylinder in a uniform free stream. The interest was to
examine the turbulence properties at the suppression of periodicity in
vortex formation process. An experimental study of the turbulent near
wake of a rotating circular cylinder was made at a Reynolds number
of 9000 for velocity ratios, λ between 0 and 2.7. Hot-wire
anemometry and particle image velocimetry results indicate that the
rotation of the cylinder causes significant changes in the vortical
activities. The turbulence quantities are getting smaller as λ increases
due to suppression of coherent vortex structures.
Abstract: Temperature, relative humidity and overhygroscopic
moisture fields in a sandstone wall provided with interior thermal
insulation were calculated in order to assess the hygric performance
of the retrofitted wall. Computational simulations showed that during
the time period of 10 years which was subject of investigation no
overhygroscopic moisture appeared in the analyzed building
envelope so that it performed in a satisfactory way from the hygric
point of view.
Abstract: The counter flow solar air heaters, with four
transverse fins and wire mesh layers are constructed and investigated
experimentally for thermal efficiency at a geographic location of
Cyprus in the city of Famagusta. The absorber plate is replaced by
sixteen steel wire mesh layers, 0.18 x 0.18cm in cross section
opening and a 0.02cm in diameter. The wire mesh layers arranged in
three groups, first and second include 6 layers, while the third include
4 layers. All layers fixed in the duct parallel to the glazing and each
group separated from the others by wood frame thickness of 0.5cm to
reduce the pressure drop. The transverse fins arranged in a way to
force the air to flow through the bed like eight letter path with flow
depth 3cm. The proposed design has increased the heat transfer rate,
but on other hand causes a high pressure drop. The obtained results
show that, for air mass flow rate range between 0.011-0.036kg/s, the
thermal efficiency increases with increasing the air mass flow. The
maximum efficiency obtained is 65.6% for the mass flow rate of
0.036kg/s. Moreover, the temperature difference between the outlet
flow and the ambient temperature, ΔT, reduces as the air mass flow
rate increase. The maximum difference between the outlet and
ambient temperature obtained was 43°C for double pass for minimum
mass flow rate of 0.011kg/s. Comparison with a conventional solar
air heater collector shows a significantly development in the thermal
efficiency.