Abstract: This paper deals with the problem of automatic rule
generation for fuzzy systems design. The proposed approach is based
on hybrid artificial bee colony (ABC) optimization and weighted least
squares (LS) method and aims to find the structure and parameters of
fuzzy systems simultaneously. More precisely, two ABC based fuzzy
modeling strategies are presented and compared. The first strategy
uses global optimization to learn fuzzy models, the second one
hybridizes ABC and weighted least squares estimate method. The
performances of the proposed ABC and ABC-LS fuzzy modeling
strategies are evaluated on complex modeling problems and compared
to other advanced modeling methods.
Abstract: The aim of this study is to determine the effect of age
and physiological status on progesterone and energy metabolism of
Ouled Djellal (O.D) breed ewes. 40 healthy ewes were divided into
two groups, primiparous and multiparous, with 20 ewes in each
group. The body weights (BW) (Kg) were 46.6 ± 4.20 and 59.2 ±
3.02, and consuming less 25 to 30% of their basal energetic
requirements. The values of serum glucose, triglycerides and
cholesterol were lower in pregnant than in non-pregnant ewes. The
high to very high significant differences were found during the 15th
week of pregnancy for glycaemia and triglyceridemia respectively.
Concerning serum progesterone, a very highly significant difference
(p
Abstract: In the present work, the finite element formulation for
the investigation of the effects of a localized interfacial degeneration
on the dynamic behavior of the [90°/0°] laminated composite plate
employing the state-space technique is performed. The stiffness of
the laminate is determined by assembling the stiffnesses of subelements.
This includes an introduction of an interface layer adopting
the virtually zero-thickness formulation to model the interfacial
degeneration. Also, the kinematically consistent mass matrix and
proportional damping have been formulated to complete the free
vibration governing expression. To simulate the interfacial
degeneration of the laminate, the degenerated areas are defined from
the center propagating outwards in a localized manner. It is found
that the natural frequency, damped frequency and damping ratio of
the plate decreases as the degenerated area of the interface increases.
On the contrary, the loss factor increases correspondingly.
Abstract: Drying behavior of blanched sweet potato in a cabinet
dryer using different five air temperatures (40-80°C) and ten sweet
potato varieties sliced to 5mm thickness were investigated. The
drying data were fitted to eight models. The Modified Henderson and
Pabis model gave the best fit to the experimental moisture ratio data
obtained during the drying of all the varieties while Newton (Lewis)
and Wang and Singh models gave the least fit. The values of Deff
obtained for Bophelo variety (1.27 x 10-9 to 1.77 x 10-9 m2/s) was
the least while that of S191 (1.93 x 10-9 to 2.47 x 10-9 m2/s) was the
highest which indicates that moisture diffusivity in sweet potato is
affected by the genetic factor. Activation energy values ranged from
0.27-6.54 kJ/mol. The lower activation energy indicates that drying
of sweet potato slices requires less energy and is hence a cost and
energy saving method. The drying behavior of blanched sweet potato
was investigated in a cabinet dryer. Drying time decreased
considerably with increase in hot air temperature. Out of the eight
models fitted, the Modified Henderson and Pabis model gave the best
fit to the experimental moisture ratio data on all the varieties while
Newton, Wang and Singh models gave the least. The lower activation
energy (0.27 - 6.54 kJ/mol) obtained indicates that drying of sweet
potato slices requires less energy and is hence a cost and energy
saving method.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: In this paper, we introduce a generalized Chebyshev
collocation method (GCCM) based on the generalized Chebyshev
polynomials for solving stiff systems. For employing a technique
of the embedded Runge-Kutta method used in explicit schemes, the
property of the generalized Chebyshev polynomials is used, in which
the nodes for the higher degree polynomial are overlapped with those
for the lower degree polynomial. The constructed algorithm controls
both the error and the time step size simultaneously and further
the errors at each integration step are embedded in the algorithm
itself, which provides the efficiency of the computational cost. For
the assessment of the effectiveness, numerical results obtained by the
proposed method and the Radau IIA are presented and compared.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: In this study, we aim to demonstrate a microgrid
system experimental simulation for an easy understanding of a
large-scale microgrid system. This model is required for industrial
training and learning environments. However, in order to create an
exact representation of a microgrid system, the laboratory-scale
system must fulfill the requirements of a grid-connected inverter, in
which power values are assigned to the system to cope with the
intermittent output from renewable energy sources. Aside from that,
during fluctuations in load capacity, the grid-connected system must
be able to supply power from the utility grid side and microgrid side in
a balanced manner. Therefore, droop control is installed in the
inverter’s control board to maintain a balanced power sharing in both
sides. This power control in a stand-alone condition and droop control
in a grid-connected condition must be implemented in order to
maintain a stabilized system. Based on the experimental results, power
control and droop control can both be applied in the system by
comparing the experimental and reference values.
Abstract: We introduced an all-optical multicasting
characteristics with wavelength conversion based on a novel
all-optical triode using negative feedback semiconductor optical
amplifier. This study was demonstrated with a transfer speed of 10
Gb/s to a non-return zero 231-1 pseudorandom bit sequence system.
This multi-wavelength converter device can simultaneously provide
three channels of output signal with the support of non-inverted and
inverted conversion. We studied that an all-optical multicasting and
wavelength conversion accomplishing cross gain modulation is
effective in a semiconductor optical amplifier which is effective to
provide an inverted conversion thus negative feedback. The
relationship of received power of back to back signal and output
signals with wavelength 1535 nm, 1540 nm, 1545 nm, 1550 nm, and
1555 nm with bit error rate was investigated. It was reported that the
output signal wavelengths were successfully converted and modulated
with a power penalty of less than 8.7 dB, which the highest is 8.6 dB
while the lowest is 4.4 dB. It was proved that all-optical multicasting
and wavelength conversion using an optical triode with a negative
feedback by three channels at the same time at a speed of 10 Gb/s is a
promising device for the new wavelength conversion technology.
Abstract: GRF, Growth regulating factor, genes encode a novel
class of plant-specific transcription factors. The GRF proteins play a
role in the regulation of cell numbers in young and growing tissues
and may act as transcription activations in growth and development
of plants. Identification of GRF genes and their expression are
important in plants to performance of the growth and development of
various organs. In this study, to better understanding the structural
and functional differences of GRFs family, 45 GRF proteins
sequences in A. thaliana, Z. mays, O. sativa, B. napus, B. rapa, H.
vulgare and S. bicolor, have been collected and analyzed through
bioinformatics data mining. As a result, in secondary structure of
GRFs, the number of alpha helices was more than beta sheets and in
all of them QLQ domains were completely in the biggest alpha helix.
In all GRFs, QLQ and WRC domains were completely protected
except in AtGRF9. These proteins have no trans-membrane domain
and due to have nuclear localization signals act in nuclear and they
are component of unstable proteins in the test tube.
Abstract: This study is purposed to develop an efficient fault
detection method for Global Navigation Satellite Systems (GNSS)
applications based on adaptive noise covariance estimation. Due to the
dependence on radio frequency signals, GNSS measurements are
dominated by systematic errors in receiver’s operating environment.
In the proposed method, the pseudorange and carrier-phase
measurement noise covariances are obtained at time propagations and
measurement updates in process of Carrier-Smoothed Code (CSC)
filtering, respectively. The test statistics for fault detection are
generated by the estimated measurement noise covariances. To
evaluate the fault detection capability, intentional faults were added to
the filed-collected measurements. The experiment result shows that
the proposed method is efficient in detecting unhealthy measurements
and improves GNSS positioning accuracy against fault occurrences.
Abstract: Many quality models have been used to measure egovernment
portals quality. However, the absence of an international
consensus for e-government portals quality models results in many
differences in terms of quality attributes and measures. The aim of
this paper is to compare and analyze the existing e-government
quality models proposed in literature (those that are based on ISO
standards and those that are not) in order to propose guidelines to
build a good and useful e-government portals quality model. Our
findings show that, there is no e-government portal quality model
based on the new international standard ISO 25010. Besides that, the
quality models are not based on a best practice model to allow
agencies to both; measure e-government portals quality and identify
missing best practices for those portals.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Hydrogenated amorphous carbon (a-C:H) films have
been synthesized by a radio frequency plasma enhanced chemical
vapor deposition (rf-PECVD) technique with different bias voltage
from 0.0 to -0.5 kV. The Raman spectra displayed the polymer-like
hydrogenated amorphous carbon (PLCH) film with 0.0 to -0.1 and
a-C:H films with -0.2 to -0.5 kV of bias voltages. The surface chemical
information of all films were studied by X-ray photoelectron
spectroscopy (XPS) technique, presented to C-C (sp2 and sp3) and C-O
bonds, and relative carbon (C) and oxygen (O) atomics contents. The
O contamination had affected on structure and optical properties. The
true density of PLCH and a-C:H films were characterized by X-ray
refractivity (XRR) method, showed the result as in the range of
1.16-1.73 g/cm3 that depending on an increasing of bias voltage. The
hardness was proportional to the true density of films. In addition, the
optical properties i.e. refractive index (n) and extinction coefficient (k)
of these films were determined by a spectroscopic ellipsometry (SE)
method that give formation to in 1.62-2.10 (n) and 0.04-0.15 (k)
respectively. These results indicated that the optical properties
confirmed the Raman results as presenting the structure changed with
applied bias voltage increased.
Abstract: Climate change will affect the hydrological cycle in
many different ways such as increase in evaporation and rainfalls.
There have been growing interests among researchers to identify the
nature of trends in historical rainfall data in many different parts of
the world. This paper examines the trends in annual maximum
rainfall data from 30 stations in New South Wales, Australia by using
two non-parametric tests, Mann-Kendall (MK) and Spearman’s Rho
(SR). Rainfall data were analyzed for fifteen different durations
ranging from 6 min to 3 days. It is found that the sub-hourly
durations (6, 12, 18, 24, 30 and 48 minutes) show statistically
significant positive (upward) trends whereas longer duration (subdaily
and daily) events generally show a statistically significant
negative (downward) trend. It is also found that the MK test and SR
test provide notably different results for some rainfall event durations
considered in this study. Since shorter duration sub-hourly rainfall
events show positive trends at many stations, the design rainfall data
based on stationary frequency analysis for these durations need to be
adjusted to account for the impact of climate change. These shorter
durations are more relevant to many urban development projects
based on smaller catchments having a much shorter response time.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: One of the biggest challenges facing Theological/
Religious Education in Nigeria is access to quality learning materials.
For instance at the Trinity (Union) Theological College, Umuahia, it
was difficult for lecturers to access suitable and qualitative materials
for instruction especially the ones that would suit the African context
and stimulate a deep rooted interest among the students. Some
textbooks written by foreign authors were readily available in the
School Library, but were lacking in the College bookshops for
students to own copies. Even when the College was able to order
some of the books from abroad, it did not usher in the needed
enthusiasm expected from the students because they were either very
expensive or very difficult to understand during private studies. So it
became necessary to develop contextual materials which were
affordable and understandable, though with little success. The
National Open University of Nigeria (NOUN)’s innovation in the
development and sharing of learning resources through its Open
Courseware is a welcome development and of great assistance to
students. Apart from NOUN students who could easily access the
materials, many others from various theological/religious institutes
across the nation have benefited immensely. So, the thesis of this
paper is that the promotion of open educational resources in
theological/religious education in Nigeria would facilitate a better
informed/equipped religious leadership, which would in turn impact
its adherents for a healthier society and national development.
Adopting a narrative and historical approach within the context of
Nigeria’s educational system, the paper discusses: educational
traditions in Nigeria; challenges facing theological/religious
education in Nigeria; and benefits of open educational resources. The
study goes further to making recommendations on how OER could
positively influence theological/religious education in Nigeria. It is
expected that theologians, religious educators, and ODL practitioners
would find this work very useful.