Abstract: This paper reports a structured literature review of the
application of Health Information Technology in developing
countries, defined as the World Bank categories Low-income
countries, Lower-middle-income, and Upper-middle-income
countries. The aim was to identify and classify the various
applications of health information technology to assess its current
state in developing countries and explore potential areas of research.
We offer specific analysis and application of HIT in Libya as one of
the developing countries. A structured literature review was
conducted using the following online databases: IEEE, Science
Direct, PubMed, and Google Scholar. Publication dates were set for
2000-2013. For the PubMed search, publications in English, French,
and Arabic were specified. Using a content analysis approach, 159
papers were analyzed and a total number of 26 factors were identified
that affect the adoption of health information technology. Of the 2681
retrieved articles, 159 met the inclusion criteria which were carefully
analyzed and classified. The implementation of health information
technology across developing countries is varied. Whilst it was
initially expected financial constraints would have severely limited
health information technology implementation, some developing
countries like India have nevertheless dominated the literature and
taken the lead in conducting scientific research. Comparing the
number of studies to the number of countries in each category, we
found that Low-income countries and Lower-middle-income had
more studies carried out than Upper-middle-income countries.
However, whilst IT has been used in various sectors of the economy,
the healthcare sector in developing countries is still failing to benefit
fully from the potential advantages that IT can offer.
Abstract: The investigation on wind turbine degradation was
carried out using the nacelle wind data. The three Vestas V80-2MW
wind turbines of Sungsan wind farm in Jeju Island, South Korea were
selected for this work. The SCADA data of the wind farm for five
years were analyzed to draw power curve of the turbines. It is assumed
that the wind distribution is the Rayleigh distribution to calculate the
normalized capacity factor based on the drawn power curve of the
three wind turbines for each year. The result showed that the reduction
of power output from the three wind turbines occurred every year and
the normalized capacity factor decreased to 0.12%/year on average.
Abstract: Enterprise Architecture (EA) is employed by
enterprises for providing integrated Information Systems (ISs) in
order to support alignment of their business and Information
Technology (IT). Evaluation of EA implementation can support
enterprise to reach intended goals. There are some problems in
current evaluation methods of EA implementation that lead to
ineffectiveness implementation of EA. This paper represents current
issues on evaluation of EA implementation. In this regard, we set the
framework in order to represent evaluation’s issues based on their
functionality and structure. The results of this research not only
increase the knowledge of evaluation, but also could be useful for
both academics and practitioners in order to realize the current
situation of evaluations.
Abstract: The inspection of underneath vehicle system has been
given significant attention by governments after the threat of
terrorism become more prevalent. New technologies such as mobile
robots and computer vision are led to have more secure environment.
This paper proposed that a mobile robot like Aria robot can be used
to search and inspect the bombs under parking a lot vehicle. This
robot is using fuzzy logic and subsumption algorithms to control the
robot that movies underneath the vehicle. An OpenCV library and
laser Hokuyo are added to Aria robot to complete the experiment for
under vehicle inspection. This experiment was conducted at the
indoor environment to demonstrate the efficiency of our methods to
search objects and control the robot movements under vehicle. We
got excellent results not only by controlling the robot movement but
also inspecting object by the robot camera at same time. This success
allowed us to know the requirement to construct a new cost effective
robot with more functionality.
Abstract: Ontologies offer a means for representing and sharing
information in many domains, particularly in complex domains. For
example, it can be used for representing and sharing information
of System Requirement Specification (SRS) of complex systems
like the SRS of ERTMS/ETCS written in natural language. Since
this system is a real-time and critical system, generic ontologies,
such as OWL and generic ERTMS ontologies provide minimal
support for modeling temporal information omnipresent in these SRS
documents. To support the modeling of temporal information, one
of the challenges is to enable representation of dynamic features
evolving in time within a generic ontology with a minimal redesign
of it. The separation of temporal information from other information
can help to predict system runtime operation and to properly design
and implement them. In addition, it is helpful to provide a reasoning
and querying techniques to reason and query temporal information
represented in the ontology in order to detect potential temporal
inconsistencies. To address this challenge, we propose a lightweight
3-layer temporal Quality of Service (QoS) ontology for representing,
reasoning and querying over temporal and non-temporal information
in a complex domain ontology. Representing QoS entities in separated
layers can clarify the distinction between the non QoS entities
and the QoS entities in an ontology. The upper generic layer of
the proposed ontology provides an intuitive knowledge of domain
components, specially ERTMS/ETCS components. The separation of
the intermediate QoS layer from the lower QoS layer allows us to
focus on specific QoS Characteristics, such as temporal or integrity
characteristics. In this paper, we focus on temporal information that
can be used to predict system runtime operation. To evaluate our
approach, an example of the proposed domain ontology for handover
operation, as well as a reasoning rule over temporal relations in this
domain-specific ontology, are presented.
Abstract: In wireless communication, space-time block code (STBC), cyclic delay diversity (CDD) and space-time cyclic delay diversity (STCDD)are used as the spatial diversity schemes and have been widely studied for the reliablecommunication. If these schemes are used, the communication system can obtain the improved performance. However,the quality of the system is degraded when the distance between a source and a destination is distant in wireless communication system. In this paper, the cooperative transmission scheme using two sources is proposed and improves the performance of the wireless communication system.
Abstract: Non-destructive testing and evaluation techniques for
assessing the integrity of composite structures are essential to both
reduce manufacturing costs and out of service time of transport means
due to maintenance. In this study, Analyze into non-destructive test
characterization of carbon fiber reinforced plastics (CFRP) internal
and external defects using thermo-graphic camera and transient
thermography method. non-destructive testing were characterized by
defect size (Ø8, Ø10, Ø12, Ø14) and depth (1.2mm, 2.4mm).
Abstract: The objective of meta-analysis is to combine results
from several independent studies in order to create generalization
and provide evidence base for decision making. But recent studies
show that the magnitude of effect size estimates reported in many
areas of research significantly changed over time and this can
impair the results and conclusions of meta-analysis. A number of
sequential methods have been proposed for monitoring the effect
size estimates in meta-analysis. However they are based on statistical
theory applicable only to fixed effect model (FEM) of meta-analysis.
For random-effects model (REM), the analysis incorporates the
heterogeneity variance, τ 2 and its estimation create complications.
In this paper we study the use of a truncated CUSUM-type test with
asymptotically valid critical values for sequential monitoring in REM.
Simulation results show that the test does not control the Type I error
well, and is not recommended. Further work required to derive an
appropriate test in this important area of applications.
Abstract: The Smart Help for persons with disability (PWD) is a
part of the project SMARTDISABLE which aims to develop relevant
solution for PWD that target to provide an adequate workplace
environment for them. It would support PWD needs smartly through
smart help to allow them access to relevant information and
communicate with other effectively and flexibly, and smart editor
that assist them in their daily work. It will assist PWD in knowledge
processing and creation as well as being able to be productive at the
work place. The technical work of the project involves design of a
technological scenario for the Ambient Intelligence (AmI) - based
assistive technologies at the workplace consisting of an integrated
universal smart solution that suits many different impairment
conditions and will be designed to empower the Physically disabled
persons (PDP) with the capability to access and effectively utilize the
ICTs in order to execute knowledge rich working tasks with
minimum efforts and with sufficient comfort level. The proposed
technology solution for PWD will support voice recognition along
with normal keyboard and mouse to control the smart help and smart
editor with dynamic auto display interface that satisfies the
requirements for different PWD group. In addition, a smart help will
provide intelligent intervention based on the behavior of PWD to
guide them and warn them about possible misbehavior. PWD can
communicate with others using Voice over IP controlled by voice
recognition. Moreover, Auto Emergency Help Response would be
supported to assist PWD in case of emergency. This proposed
technology solution intended to make PWD very effective at the
work environment and flexible using voice to conduct their tasks at
the work environment. The proposed solution aims to provide
favorable outcomes that assist PWD at the work place, with the
opportunity to participate in PWD assistive technology innovation
market which is still small and rapidly growing as well as upgrading
their quality of life to become similar to the normal people at the
workplace. Finally, the proposed smart help solution is applicable in
all workplace setting, including offices, manufacturing, hospital, etc.
Abstract: This paper presents the application of the Discrete
Component Model for heating and evaporation to multi-component
biodiesel fuel droplets in direct injection internal combustion engines.
This model takes into account the effects of temperature gradient,
recirculation and species diffusion inside droplets. A distinctive
feature of the model used in the analysis is that it is based on the
analytical solutions to the temperature and species diffusion
equations inside the droplets. Nineteen types of biodiesel fuels are
considered. It is shown that a simplistic model, based on the
approximation of biodiesel fuel by a single component or ignoring
the diffusion of components of biodiesel fuel, leads to noticeable
errors in predicted droplet evaporation time and time evolution of
droplet surface temperature and radius.
Abstract: Nanocrystalline powders of the lead-free piezoelectric
material, tantalum-substituted potassium sodium niobate
(K0.5Na0.5)(Nb0.9Ta0.1)O3 (KNNT), were produced using a Retsch
PM100 planetary ball mill by setting the milling time to 15h, 20h,
25h, 30h, 35h and 40h, at a fixed speed of 250rpm. The average
particle size of the milled powders was found to decrease from 12nm
to 3nm as the milling time increases from 15h to 25h, which is in
agreement with the existing theoretical model. An anomalous
increase to 98nm and then a drop to 3nm in the particle size were
observed as the milling time further increases to 30h and 40h
respectively. Various sizes of these starting KNNT powders were
used to investigate the effect of milling time on the microstructure,
dielectric properties, phase transitions and piezoelectric properties of
the resulting KNNT ceramics. The particle size of starting KNNT
was somewhat proportional to the grain size. As the milling time
increases from 15h to 25h, the resulting ceramics exhibit
enhancement in the values of relative density from 94.8% to 95.8%,
room temperature dielectric constant (εRT) from 878 to 1213, and
piezoelectric charge coefficient (d33) from 108pC/N to 128pC/N. For
this range of ceramic samples, grain size refinement suppresses the
maximum dielectric constant (εmax), shifts the Curie temperature (Tc)
to a lower temperature and the orthorhombic-tetragonal phase
transition (Tot) to a higher temperature. Further increase of milling
time from 25h to 40h produces a gradual degradation in the values of
relative density, εRT, and d33 of the resulting ceramics.
Abstract: Social media continues to grow, and user interfaces
may become more appealing if cultural characteristics are
incorporated into their design.
Facebook was designed in the west, and the original language was
English. Subsequently, the words in the user interface were translated
to other languages, including Arabic.
Arabic words are written from right to left, and English is written
from left to right. The translated version may misrepresent the
original design and users’ preferences may be influenced by their
culture, which should be considered in the user interface design.
Previous research indicates that users are more comfortable when
interacting with a user interface, which relates to their own culture.
Therefore, this paper, using a survey, investigates the preferences of
Saudi Arabians on the Arabic version of the user interface of
Facebook.
Abstract: PVC foam-fly ash composites (PVC-FA) are
characterized for their structural, morphological, mechanical and
thermal properties. The tensile strength of the composites increased
modestly with higher fly ash loading, while there was a significant
increase in the elastic modulus for the same composites. On the other
hand, a decrease in elongation at UTS was observed upon increasing
fly ash content due to increased rigidity of the composites. Similarly,
the flexural modulus increased as the fly ash loading increased,
where the composites containing 25 phr fly ash showed the highest
flexural strength. Thermal properties of PVC-fly ash composites were
determined by Thermo Gravimetric Analysis (TGA). The
microstructural properties were studied by Scanning Electron
Microscopy (SEM). SEM results confirm that fly ash particles were
mechanically interlocked in PVC matrix with good interfacial
interaction with the matrix. Particle agglomeration and debonding
was observed in samples containing higher amounts of fly ash.
Abstract: Two types of glass fibers having different lengths
(1/16" and 1/32") were added into rigid PVC foams to enhance the
dimensional stability of extruded rigid Polyvinyl Chloride (PVC)
foam at different concentrations (0-20 phr) using a single screw
profile extruder. PVC foam-glass fiber composites (PVC-GF) were
characterized for their dimensional stability, structural, thermal, and
mechanical properties. Experimental results show that the
dimensional stability, heat resistance, and storage modulus were
enhanced without compromising the tensile and flexural strengths of
the composites. Overall, foam composites which were prepared with
longer glass fibers exhibit better mechanical and thermal properties
than those prepared with shorter glass fibers due to higher
interlocking between the fibers and the foam cells, which result in
better load distribution in the matrix.
Abstract: Communicating and managing customers’
requirements in software development projects play a vital role in the
software development process. While it is difficult to do so locally, it
is even more difficult to communicate these requirements over
distributed boundaries and to convey them to multiple distribution
customers. This paper discusses the communication of multiple
distribution customers’ requirements in the context of customised
software products. The main purpose is to understand the challenges
of communicating and managing customisation requirements across
distributed boundaries. We propose a model for Communicating
Customisation Requirements of Multi-Clients in a Distributed
Domain (CCRD). Thereafter, we evaluate that model by presenting
the findings of a case study conducted with a company with
customisation projects for 18 distributed customers. Then, we
compare the outputs of the real case process and the outputs of the
CCRD model using simulation methods. Our conjecture is that the
CCRD model can reduce the challenge of communication
requirements over distributed organisational boundaries, and the
delay in decision making and in the entire customisation process
time.
Abstract: In this study, microcrystalline cellulose (MCC) was
extracted from oil palm empty fruit bunch (EFB) cellulose which was
earlier isolated from oil palm EFB fibre. In order to isolate the
cellulose, the chlorination method was carried out. Then, the MCC
was prepared by simultaneous ultrasonic and alkali treatment from
the isolated α-cellulose. Based on mass balance calculation, the yields
for MCC obtained from EFB was 44%. For fiber characterization, it
is observed that the chemical composition of the hemicellulose and
lignin for all samples decreased while composition for cellulose
increased. The structural property of the MCC was studied by X-ray
diffraction (XRD) method and the result shows that the MCC
produced is a cellulose-I polymorph, with 73% crystallinity.
Abstract: Among modern airflow measurement methods,
Particle Image Velocimetry (PIV) and Particle Tracking Velocimetry
(PTV), as visualized and non-instructive measurement techniques, are
playing more important role. This paper conducts a comparative
experimental study for airflow measurement employing both
techniques with the same condition. Velocity vector fields, velocity
contour fields, voticity profiles and turbulence profiles are selected as
the comparison indexes. The results show that the performance of both
PIV and PTV techniques for airflow measurement is satisfied, but
some differences between the both techniques are existed, it suggests
that selecting the measurement technique should be based on a
comprehensive consideration.
Abstract: This paper discusses the role of music as a ludic
activity and constituent element of voice in the construction and
consolidation of the relationship of the baby and his/her mother or
caretaker, evaluating its implications in his/her psychic structure and
constitution as a subject. The work was based on the research
developed as part of the author’s doctoral activities carried out from
her insertion in a project of the Music Department of Federal
University of Rio Grande do Sul - UFRGS, which objective was the
development of musical activities with groups of babies from 0 to 24
months old and their caretakers. Observations, video recordings of
the meetings, audio testemonies, and evaluation tools applied to
group participants were used as instruments for this research.
Information was collected on the participation of 195 babies, among
which 8 were more focused on through interviews with their mothers
or caretakers. These interviews were analyzed based on the
referential of French Discourse Analysis, Psychoanalysis, Psychology
of Development and Musical Education. The results of the research
were complemented by other posterior experiences that the author
developed with similar groups, in a context of a private clinic. The
information collected allowed the observation of the ludic and
structural functions of musical activities, when developed in a
structured environment, as well as the importance of the musicality of
the mother’s voice to the psychical structuring of the baby, allowing
his/her insertion in the language and his/her constitution as a subject.
Abstract: In EFL programs, rating scales used in writing
assessment are often constructed by intuition. Intuition-based scales
tend to provide inaccurate and divisive ratings of learners’ writing
performance. Hence, following an empirical approach, this study
attempted to develop a rating scale for elementary-level writing at an
EFL program in Saudi Arabia. Towards this goal, 98 students’ essays
were scored and then coded using comprehensive taxonomy of
writing constructs and their measures. An automatic linear modeling
was run to find out which measures would best predict essay scores.
A nonparametric ANOVA, the Kruskal-Wallis test, was then used to
determine which measures could best differentiate among scoring
levels. Findings indicated that there were certain measures that could
serve as either good predictors of essay scores or differentiators
among scoring levels, or both. The main conclusion was that a rating
scale can be empirically developed using predictive and
discriminative statistical tests.
Abstract: Children are more susceptible to medication errors
than adults. Medication administration process is the last stage in the
medication treatment process and most of the errors detected in this
stage. Little research has been undertaken about medication errors in
children in the Middle East countries. This study was aimed to
evaluate how the paediatric nurses adhere to the medication
administration policy and also to identify any medication preparation
and administration errors or any risk factors. An observational,
prospective study of medication administration process from when
the nurses preparing patient medication until administration stage
(May to August 2014) was conducted in Saudi Arabia. Twelve
paediatric nurses serving 90 paediatric patients were observed. 456
drug administered doses were evaluated. Adherence rate was variable
in 7 steps out of 16 steps. Patient allergy information, dose
calculation, drug expiry date were the steps in medication
administration with lowest adherence rates. 63 medication
preparation and administration errors were identified with error rate
13.8% of medication administrations. No potentially life-threating
errors were witnessed. Few logistic and administrative factors were
reported. The results showed that the medication administration
policy and procedure need an urgent revision to be more sensible for
nurses in practice. Nurses’ knowledge and skills regarding to the
medication administration process should be improved.