Abstract: This paper presents a model for a modified T-junction
device for microspheres generation. The numerical model is
developed using a commercial software package: COMSOL
Multiphysics. In order to test the accuracy of the numerical model,
multiple variables, such as the flow rate of cross-flow, fluid properties,
structure, and geometry of the microdevice are applied. The results
from the model are compared with the experimental results in the
diameter of the microsphere generated. The comparison shows a good
agreement. Therefore the model is useful in further optimization of the
device and feedback control of microsphere generation if any.
Abstract: This study investigates the suitability of using plastic,
such as polyethylene terephthalate (PET), as a partial replacement of
natural coarse and fine aggregates (for example, brick chips and
natural sand) to produce lightweight concrete for load bearing
structural members. The plastic coarse aggregate (PCA) and plastic
fine aggregate (PFA) were produced from melted polyethylene
terephthalate (PET) bottles. Tests were conducted using three
different water–cement (w/c) ratios, such as 0.42, 0.48, and 0.57,
where PCA and PFA were used as 50% replacement of coarse and
fine aggregate respectively. Fresh and hardened properties of
concrete have been compared for natural aggregate concrete (NAC),
PCA concrete (PCC) and PFA concrete (PFC). The compressive
strength of concrete at 28 days varied with the water–cement ratio for
both the PCC and PFC. Between PCC and PFC, PFA concrete
showed the highest compressive strength (23.7 MPa) at 0.42 w/c ratio
and also the lowest compressive strength (13.7 MPa) at 0.57 w/c
ratio. Significant reduction in concrete density was mostly observed
for PCC samples, ranging between 1977–1924 kg/m³. With the
increase in water–cement ratio PCC achieved higher workability
compare to both NAC and PFC. It was found that both the PCA and
PFA contained concrete achieved the required compressive strength
to be used for structural purpose as partial replacement of the natural
aggregate; but to obtain the desired lower density as lightweight
concrete the PCA is most suited.
Abstract: All the software engineering researches and best
industry practices aim at providing software products with high
degree of quality and functionality at low cost and less time. These
requirements are addressed by the Component Based Software
Engineering (CBSE) as well. CBSE, which deals with the software
construction by components’ assembly, is a revolutionary extension
of Software Engineering. CBSE must define and describe processes
to assure timely completion of high quality software systems that are
composed of a variety of pre built software components. Though
these features provide distinct and visible benefits in software design
and programming, they also raise some challenging problems. The
aim of this work is to summarize the pertinent issues and
considerations in CBSE to make an understanding in forms of
concepts and observations that may lead to development of newer
ways of dealing with the problems and challenges in CBSE.
Abstract: Activated carbon is an amorphous carbon chain which
has extremely extended surface area. High surface area of activated
carbon is due to the porous structure. Activated carbon, using a
variety of materials such as coal and cellulosic materials; can be
obtained by both physical and chemical methods. The prepared
activated carbon can be used for decolorize, deodorize and also can
be used for removal of organic and non-organic pollution. In this
study, pomegranate peel was subjected to 800W microwave power
for 1 to 4 minutes. Also fresh pomegranate peel was used for the
reference material. Then ZnCl2 was used for the chemical activation
purpose. After the activation process, activated pomegranate peels
were used for the adsorption of Zn metal (40 ppm) in the waste water.
As a result of the adsorption experiments, removal of heavy metals
ranged from 89% to 85%.
Abstract: Optical radiation emitted from a metal-coated fiber tip apex at liquid-air interface was measured. The intensity of the output radiation was strongly depend on the relative position of the tip to a liquid-air interface and varied with surface fluctuations. This phenomenon permits in-situ real-time investigation of nano-metric vibrations of the liquid surface and provides a basis for development of various origin ultrasensitive vibration detecting sensors. The described method can be used for detection of week seismic vibrations.
Abstract: In 2010-2011, the research on zooplankton was
conducted in the southern part of the Baltic Sea to determine seasonal
variability in changes occurring throughout the zooplankton in 2010
and 2011, both in the region of Gdańsk Deep, and in the western part
of Gdańsk Bay. The research in the sea showed that the taxonomic
composition of holoplankton in the southern part of the Baltic Sea
was similar to that recorded in this region for many years. The
maximum values of abundance and biomass of zooplankton both in
the Deep and the Bay of Gdańsk were observed in the summer
season. Copepoda dominated in the composition of zooplankton for
almost the entire study period, while rotifers occurred in larger
numbers only in the summer 2010 in the Gdańsk Deep as well as in
May and July 2010 in the western part of Gdańsk Bay, and
meroplankton – in April 2011.
Abstract: In this paper, the effects of fiber types and elevated
temperatures on compressive strength, modulus of rapture and the
bond characteristics of fiber reinforced concretes (FRC) are
presented. By using the three different types of fibers (steel fiber-SF,
polypropylene-PPF and polyvinyl alcohol-PVA), FRC specimens
were produced and exposed to elevated temperatures up to 800 ºC for
1.5 hours. In addition, a plain concrete (without fiber) was produced
and used as a control. Test results obtained showed that the steel fiber
reinforced concrete (SFRC) had the highest compressive strength,
modulus of rapture and bond stress values at room temperatures, the
residual bond, flexural and compressive strengths of both FRC and
plain concrete dropped sharply after exposure to high temperatures.
The results also indicated that the reduction of bond, flexural and
compressive strengths with increasing the exposed temperature was
relatively less for SFRC than for plain, and FRC with PPF and PVA.
Abstract: After the internet explosion in the 90’s, technology
was immediately integrated into the school system. Technology
which symbolizes advancement in human knowledge was seen as a
setback by many educators. Efforts have been made to help stem this
erroneous believes and help educators realize the benefits of
technology and ways of implementing it in the classrooms especially
in the sciences. This advancement created a constantly expanding gap
between the pupil’s perception on the use of technology within the
learning atmosphere and the teacher’s perception and limitations
hence, the focus of this paper is on the need to refocus on the use of
Science and Technology in enhancing children’s potentials in
learning at school especially in Science for sustainable development
in Nigeria. The paper recommended measures for facilitating the
sustenance of science and technology in Nigerian schools so as to
enhance the potentials of our children in Science and Technology for
a better tomorrow.
Abstract: The paper presents an innovative networked radar
system for detection of obstacles in a railway level crossing scenario.
This Monitoring System (MS) is able to detect moving or still
obstacles within the railway level crossing area automatically,
avoiding the need of human presence for surveillance. The MS is also
connected to the National Railway Information and Signaling System
to communicate in real-time the level crossing status. The
architecture is compliant with the highest Safety Integrity Level
(SIL4) of the CENELEC standard. The number of radar sensors used
is configurable at set-up time and depends on how large the level
crossing area can be. At least two sensors are expected and up four
can be used for larger areas. The whole processing chain that
elaborates the output sensor signals, as well as the communication
interface, is fully-digital, was designed in VHDL code and
implemented onto a Xilinx Virtex 6.
Abstract: The mechanisms underlying the association between
obesity and asthma may be related to a decreased immunological
tolerance induced by a defective function of regulatory T cells
(Tregs). The aim of this study is to establish the potential link
between these diseases and CD4+, CD25+ FoxP3+ Tregs as well as T
helper cells (Ths) in children. This is a prospective case control
study. Obese (n:40), asthmatic (n:40), asthmatic obese (n:40) and
healthy children (n:40), who don't have any acute or chronic diseases,
were included in this study. Obese children were evaluated according
to WHO criteria. Asthmatic patients were chosen based on GINA
criteria. Parents were asked to fill up the questionnaire. Informed
consent forms were taken. Blood samples were marked with CD4+,
CD25+ and FoxP3+ in order to determine Tregs and Ths by flow
cytometric method. Statistical analyses were performed. p≤0.05 was
chosen as meaningful threshold. Tregs exhibiting anti-inflammatory
nature were significantly lower in obese (0,16%; p≤0,001), asthmatic
(0,25%; p≤0,01) and asthmatic obese (0,29%; p≤0,05) groups than
the control group (0,38%). Ths were counted higher in asthma group
than the control (p≤0,01) and obese (p≤0,001) groups. T cell
immunity plays important roles in obesity and asthma pathogeneses.
Decreased numbers of Tregs found in obese, asthmatic and asthmatic
obese children may help to elucidate some questions in
pathophysiology of these diseases. For HOMA-IR levels, any
significant difference was not noted between control and obese
groups, but statistically higher values were found for obese
asthmatics. The values obtained in all groups were found to be below
the critical cut off points. This finding has made the statistically
significant difference observed between Tregs of obese, asthmatic,
obese asthmatic and control groups much more valuable. These
findings will be useful in diagnosis and treatment of these disorders
and future studies are needed. The production and propagation of
Tregs may be promising in alternative asthma and obesity treatments.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: Predicting the collapse potential of a structure during
earthquakes is an important issue in earthquake engineering. Many
researchers proposed different methods to assess the collapse
potential of structures under the effect of strong ground motions.
However most of them did not consider degradation and softening
effect in hysteretic behavior. In this study, collapse potential of
SDOF systems caused by dynamic instability with stiffness and
strength degradation has been investigated. An equation was
proposed for the estimation of collapse period of SDOF system which
is a limit value of period for dynamic instability. If period of the
considered SDOF system is shorter than the collapse period then the
relevant system exhibits dynamic instability and collapse occurs.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.
Abstract: This paper describes the issues relating to the role of
the flash flood early warning system provided by the Malaysian
Government to the communities in Malaysia, specifically during the
flash flood disaster in the Cameron Highlands, Malaysia. Normally,
flash flood disasters can occur as a result of heavy rainfall in an area,
and that water may possibly cause flooding via streams or narrow
channels. The focus of this study is the flash flood disaster which
occurred on 23 October 2013 in the Cameron Highlands, and as a
result the Sungai Bertam overflowed after the release of water from
the Sultan Abu Bakar Dam. This release of water from the dam
caused flash flooding which led to damage to properties and also the
death of residents and livestock in the area. Therefore, the effort of
this study is to identify the perceptions of the flash flood victims on
the role of the flash flood early warning system. For the purposes of
this study, data were gathered through face-to-face interviews from
those flood victims who were willing to participate in this study. This
approach helped the researcher to glean in-depth information about
their feelings and perceptions of the role of the flash flood early
warning system offered by the government. The data were analysed
descriptively and the findings show that the respondents of 22 flood
victims believe strongly that the flash flood early warning system was
confusing and dysfunctional, and communities had failed to response
positively to it. Therefore, most of the communities were not well
prepared for the releasing of water from the dam which caused
property damage, and 3 people were killed in the Cameron Highland
flash flood disaster.
Abstract: Specific leaf area (SLA; cm2leaf g-1leaf) the ratio of leaf
area to leaf dry mass is a key ecophysiological parameter influencing
leaf physiology, photosynthesis, and whole plant carbon gain and
also can be used as a rapid and diagnostic tool. In this study, two
species of soluble inorganic selenium forms, selenite (Se^IV) and
selenate (Se^VI) at different concentrations were investigated on maize
plants that were growing in nutrient solutions during 2 weeks and at
the end of the experiment, amounts of SLA for first and second
leaves of maize were measured. In accordance with the results we
observed that our regarded Se concentrations in both forms of Se^IV
and Se^VI were not effective on maize plants’ SLA significantly
although high level of 3 mg.kg-1 Se^IV had negative affect on growth
of the samples that had been treated by it but about Se^VI samples we
did not observe this state and our different considered Se^VI
concentrations were not toxic for maize plants.
Abstract: The paper discusses mineral water consumer market
and development policy in Georgia, the tools and measures, which
will contribute to production of mineral waters and increase its
export.
The paper studies and analyses current situation in mineral water
production sector as well as the factors affecting increase and
reduction of its export. It’s noted that in order to gain and maintain
competitive advantage, it’s necessary to provide continuous supply of
high quality goods with modern design, open new distribution
channels to enter new markets, carry out broad promotional activities,
organize e-commerce. Economic policy plays an important role in
protecting markets from counterfeit goods. The state also plays an
important role in attracting foreign direct investments. Stable
business environment and export oriented strategy is the basis for the
country’s economic growth.
Based on the research, the paper suggests the strategy for
improving competitiveness of Georgian mineral waters; relevant
conclusions and recommendations are provided.
Abstract: Problems insulation of building structures is often
closely connected with the problem of moisture remediation. In the
case of historic buildings or if only part of the redevelopment of
envelope of structures, it is not possible to apply the classical external
thermal insulation composite systems. This application is mostly
effective thermal insulation plasters with high porosity and controlled
capillary properties which assures improvement of thermal properties
construction, its diffusion openness towards the external environment
and suitable treatment capillary properties of preventing the
penetration of liquid moisture and salts thereof toward the outer
surface of the structure.
With respect to the current trend of reducing the energy
consumption of building structures and reduce the production of CO2
is necessary to develop capillary-active materials characterized by
their low density, low thermal conductivity while maintaining good
mechanical properties. The aim of researchers at the Faculty of Civil
Engineering, Brno University of Technology is the development and
study of hygrothermal behaviour of optimal materials for thermal
insulation and rehabilitation of building structures with the possible
use of alternative, less energy demanding binders in comparison with
conventional, frequently used binder, which represents cement.
The paper describes the evaluation of research activities aimed at
the development of thermal insulation and repair materials using
lightweight aggregate and alternative binders such as metakaolin and
finely ground fly ash.
Abstract: The aim of the present study was to examine whether
increasing molybdenum (Mo) concentration affects the growth and
Mo concentration of maize (Zea mays L. cv Norma SC) and
sunflower (Helianthus annuus L. cv Arena PR) seedlings within
laboratory conditions.
In this experiment, calcareous chernozem soil was used and Mo
was supplemented into the soil as ammonium molybdate
[(NH4)6Mo7O24.4H2O] in four different concentrations as follow: 0
(control), 30, 90 and 270 mg·kg-1.
In this study, we found that molybdenum in small amount (30
mg·kg-1) affects positively on growth of maize and sunflower
seedlings, however, higher concentration of Mo reduces the dry
weights of shoots and roots. In the case of maize the highest Mo
treatment (270 mg·kg-1) and in sunflower 90 mg·kg-1 treatment
caused significant reduction in plant growth.
In addition, we observed that molybdenum contents in the roots
and shoots were very low in case of control soil but were
significantly elevated with increasing concentration of Mo treatment.
Only in case of sunflower the highest 270 mg·kg-1 Mo treatment
caused decrease in Mo concentration.
Abstract: Significant quota of Municipal Electrical Energy
consumption is related to Decentralized Air Conditioning which is
mostly provided by evaporative coolers. So the aim is to optimize
design of air conditioners to increase their efficiencies. To achieve
this goal, results of practical standardized tests for 40 evaporative
coolers in different types collected and simultaneously results for
same coolers based on one of EER (Energy Efficiency Ratio)
modeling styles are figured out. By comparing experimental results
of different coolers standardized tests with modeling results,
preciseness of used model is assessed and after comparing gained
preciseness with international standards based on EER for cooling
capacity, aeration, and also electrical energy consumption, energy
label from A (most effective) to G (less effective) is classified; finally
needed methods to optimize energy consumption and coolers’
classification are provided.