Abstract: Most parts of the world such as Iran are facing the excessive consumption of fertilizers, that are used to achieve high yield, but increase the cost of production of fertilizer and degradation of soil and water resources. This experiment was carried out to study the effect of PGPR and planting pattern on yield and yield components of rice (Oryza sativa L.) using split plot based on randomized complete block design with three replications in Ilam province, Iran. Bio-fertilizer including Azotobacter, Nitroxin and control treatment (without consumption) were designed as a main plot and planting pattern including 15 × 10, 15 × 15 and 15 × 20 and the number of plant in hill including 3, 4 and 5 plants in hill were considered as a sub-plots. The results showed that the effect of bio-fertilizers, planting pattern and the number of plants in hill were significant affect on yield and yield components. Interaction effect between bio-fertilizer and planting pattern had important difference on the number spikelet of panicle and harvest index. Interaction effect between bio-fertilizer and the number of plants in hill were significant affect on the number of spikelet per panicle. The maximum grain yield was obtained by inoculation with Nitroxin, planting pattern of 15 × 15 and 4 plants in hill with mean of 1110.6 g.m-2, 959.9 g.m-2 and 928.4 g.m-2, respectively.
Abstract: Populations of wild boar present in semi-arid of central Iran. We studied features influencing bed site selection by this species in semi-arid central steppe of Iran. Habitat features of the detected bed site were compared with randomly selected by quantifying number of habitat variables in semi- arid area in Iran. The results revealed that the most important influencing factors in bed site selection were vegetation cover, number of Artemisia sieberi, percentage cover and height of Acer cinerascens, percentage cover and height of Amygdalus scoparia. This is the first ecological study of the wild boar in a protected area of the semi desert biome of Iran. Sustainability of wild boar populations in this area dependent to shrubs of Amygdalus scoparia and Acer cinerascens for thermal and camouflage cover.
Abstract: The response of King Abdulla Canal (KAC) water to the upgrade of As Samra Wastewater Treatment Plant which discharges its effluent to the Zarqa River is investigated. Time series quality data that extends between October 2005 and December 2009 obtained by a state of the art telemetric monitoring system were analyzed for COD, EC, TP and TN at two monitoring stations located upstream and downstream of the confluence of the Zarqa River with KAC. The samples- means and the t-test showed that there has been significant improvement in the quality of the KAC water for COD, and TP. However, the improvement in the TN was found statistically insignificant, whereas the EC of the KAC was unaffected by the upgrade. Comparing the selected parameters with the standards and guidelines for using treated wastewater in irrigation showed that the KAC water has improved towards meeting the required standards and guidelines for treated wastewater reuse in irrigation.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In this article the homotopy continuation method (HCM) to solve the forward kinematic problem of the 3-PRS parallel manipulator is used. Since there are many difficulties in solving the system of nonlinear equations in kinematics of manipulators, the numerical solutions like Newton-Raphson are inevitably used. When dealing with any numerical solution, there are two troublesome problems. One is that good initial guesses are not easy to detect and another is related to whether the used method will converge to useful solutions. Results of this paper reveal that the homotopy continuation method can alleviate the drawbacks of traditional numerical techniques.
Abstract: Thermal conductivity is an important characteristic of
a nanofluid in laminar flow heat transfer. This paper presents an
improved model for the prediction of the effective thermal
conductivity of nanofluids based on dimensionless groups. The
model expresses the thermal conductivity of a nanofluid as a function
of the thermal conductivity of the solid and liquid, their volume
fractions and particle size. The proposed model includes a parameter
which accounts for the interfacial shell, brownian motion, and
aggregation of particle. The validation of the model is verified by
applying the results obtained by the experiments of Tio2-water and
Al2o3-water nanofluids.
Abstract: Machining is an important manufacturing process used to produce a wide variety of metallic parts. Among various machining processes, turning is one of the most important one which is employed to shape cylindrical parts. In turning, the quality of finished product is measured in terms of surface roughness. In turn, surface quality is determined by machining parameters and tool geometry specifications. The main objective of this study is to simultaneously model and optimize machining parameters and tool geometry in order to improve the surface roughness for AISI1045 steel. Several levels of machining parameters and tool geometry specifications are considered as input parameters. The surface roughness is selected as process output measure of performance. A Taguchi approach is employed to gather experimental data. Then, based on signal-to-noise (S/N) ratio, the best sets of cutting parameters and tool geometry specifications have been determined. Using these parameters values, the surface roughness of AISI1045 steel parts may be minimized. Experimental results are provided to illustrate the effectiveness of the proposed approach.
Abstract: This paper presents a novel method for prediction of
the mechanical behavior of proximal femur using the general
framework of the quantitative computed tomography (QCT)-based
finite element Analysis (FEA). A systematic imaging and modeling
procedure was developed for reliable correspondence between the
QCT-based FEA and the in-vitro mechanical testing. A speciallydesigned
holding frame was used to define and maintain a unique
geometrical reference system during the analysis and testing. The
QCT images were directly converted into voxel-based 3D finite
element models for linear and nonlinear analyses. The equivalent
plastic strain and the strain energy density measures were used to
identify the critical elements and predict the failure patterns. The
samples were destructively tested using a specially-designed gripping
fixture (with five degrees of freedom) mounted within a universal
mechanical testing machine. Very good agreements were found
between the experimental and the predicted failure patterns and the
associated load levels.
Abstract: The knee bracing steel frame (KBF) is a new kind of energy dissipating frame, which combines excellent ductility and lateral stiffness. In this framing system, a special form of diagonal brace connected to a knee element instead of beam-column joint, is investigated. Recently, a similar system was proposed and named as chevron knee bracing system (CKB) which in comparison with the former system has a better energy absorption characteristic and at the same time retains the elastic nature of the structures. Knee bracing can provide a stiffer bracing system but reduces the ductility of the steel frame. Chevron knee bracing can be employed to provide the desired ductility level for a design. In this article, relation between seismic performance and structural parameters of the two above mentioned systems are investigated and compared. Frames with similar dimensions but various heights in both systems are designed according to Iranian code of practice for seismic resistant design of building, and then based on a non-linear push over static analysis; the seismic parameters such as behavior factor and performance levels are compared.
Abstract: Combining classifiers is a useful method for solving
complex problems in machine learning. The ECOC (Error Correcting
Output Codes) method has been widely used for designing combining
classifiers with an emphasis on the diversity of classifiers. In this
paper, in contrast to the standard ECOC approach in which individual
classifiers are chosen homogeneously, classifiers are selected
according to the complexity of the corresponding binary problem. We
use SATIMAGE database (containing 6 classes) for our experiments.
The recognition error rate in our proposed method is %10.37 which
indicates a considerable improvement in comparison with the
conventional ECOC and stack generalization methods.
Abstract: In this paper the multi-mode resource-constrained project scheduling problem with discounted cash flows is considered. Minimizing the makespan and maximization the net present value (NPV) are the two common objectives that have been investigated in the literature. We apply one evolutionary algorithm named multiobjective particle swarm optimization (MOPSO) to find Pareto front solutions. We used standard sets of instances from the project scheduling problem library (PSPLIB). The results are computationally compared respect to different metrics taken from the literature on evolutionary multi-objective optimization.
Abstract: This paper presents a new adaptive DMC controller
that improves the controller performance in case of plant-model
mismatch. The new controller monitors the plant measured output,
compares it with the model output and calculates weights applied to
the controller move. Simulations show that the new controller can
help improve control performance and avoid instability in case of
severe model mismatches.
Abstract: In this paper a novel high output impedance, low input impedance, wide bandwidth, very simple current mirror with input and output voltage requirements less than that of a simple current mirror is presented. These features are achieved with very simple structure avoiding extra large node impedances to ensure high bandwidth operation. The circuit's principle of operation is discussed and compared to simple and low voltage cascode (LVC) current mirrors. Such outstanding features of this current mirror as high output impedance ~384K, low input impedance~6.4, wide bandwidth~178MHz, low input voltage ~ 362mV, low output voltage ~ 38mV and low current transfer error ~4% (all at 50μA) makes it an outstanding choice for high performance applications. Simulation results in BSIM 0.35μm CMOS technology with HSPICE are given in comparison with simple, and LVC current mirrors to verify and validate the performance of the proposed current mirror.
Abstract: This experiment was conducted to investigate the
effect of different levels of dietary chromium yeast (Cr-yeast) on
thigh meat quality of broiler chicks reared under heat stress
condition. Two hundred and forty Ross male chickens in heat stress
condition (33±3°C) were allocated to five treatments in a completely
randomized design. Treatments were supplemented with 0 (control),
200, 400, 800 and 1200 μg kg-1 Cr in the form of Cr yeast. Twelve
chicks from each treatment were slaughtered at 42 d, to evaluate
moisture, protein, lipid, pH and lipid oxidation of thigh meat.
Protein, moisture, lipid and pH of thigh meat were not affected by
supplemental Cr. Thigh meat lipid tended to decrease in broilers
received 1200 μg kg-1. Storage time increased lipid oxidation of
meat (P
Abstract: In the present study, the rate of NOx emission in a
combustion chamber working in conventional combustion and High
Temperature Air Combustion (HiTAC) system are examined using
CFD modeling. The effect of peak temperature, combustion air
temperature and oxygen concentration on NOx emission rate was
undertaken. Results show that in a fixed oxygen concentration,
increasing the preheated air temperature will increase the peak
temperature and NOx emission rate. In addition, it was observed that
the reduction of the oxygen concentration in the fixed preheated air
temperature decreases the peak temperature and NOx emission rate.
On the other hand, the results show that increase of preheated air
temperature at various oxygen concentrations increases the NOx
emission rate. However, the rate of increase in HiTAC conditions is
quite lower than the conventional combustion. The modeling results
show that the NOx emission rate in HiTAC combustion is 133% less
than that of the conventional combustion.
Abstract: DG application has received increasing attention during
recent years. The impact of DG on various aspects of distribution system
operation, such as reliability and energy loss, depend highly on DG
location in distribution feeder. Optimal DG placement is an important
subject which has not been fully discussed yet.
This paper presents an optimization method to determine optimal DG
placement, based on a cost/worth analysis approach. This method
considers technical and economical factors such as energy loss, load point
reliability indices and DG costs, and particularly, portability of DG. The
proposed method is applied to a test system and the impacts of different
parameters such as load growth rate and load forecast uncertainty (LFU)
on optimum DG location are studied.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: As a primitive assumption, if a new information
system is able to remind users their old work habits, it should have a
better opportunity to be accepted, adopted and finally, utilized. In
this paper some theoretical concepts borrowed from psychodynamic
theory e.g. ego defenses are discussed to show how such resemblance
can be made without necessarily affecting the performance of the
new system. The main assertion is a new system should somehow
imitate old work habits, not literally, but through following their
paces in terms of the order of habitual tensional states including
stimulation, defensive actions and satisfactions.