Abstract: Sisal leaves were subjected to enzymatic retting
method to extract the sisal fibre. A portion of the fibre was pretreated
with alkali (NaOH), and further treated with benzoyl chloride
and silane treatment reagents. Both the treated and untreated Sisal
fibre composites were used to fabricate the composite by hand lay-up
technique using unsaturated polyester resin. Tensile, flexural, water
absorption, density, thickness swelling and chemical resistant tests
were conducted and evaluated on the composites. Results obtained
for all the parameters showed an increase in the treated fibre
compared to untreated fibre. FT-IR spectra results ascertained the
inclusion of benzoyl and silane groups on the fibre surface. Scanning
electron microscopy (SEM) result obtained showed variation in the
morphology of the treated and untreated fibre. Chemical modification
was found to improve adhesion of the fibre to the matrix, as well as
physico-mechanical properties of the composites.
Abstract: The combination of multi–walled carbon nanotubes
(MWCNTs) with polymers offers an attractive route to reinforce the
macromolecular compounds as well as the introduction of new
properties based on morphological modifications or electronic
interactions between the two constituents. As they are only a few
nanometers in dimension, it offers ultra-large interfacial area per
volume between the nano-element and polymer matrix. Nevertheless,
the use of MWCNTs as a rough material in different applications has
been largely limited by their poor processability, insolubility, and
infusibility. Studies concerning the nanofiller reinforced polymer
composites are justified in an attempt to overcome these limitations.
This work presents one preliminary study of MWCNTs dispersion
into the PVDF homopolymer. For preparation, the composite
components were diluted in n,n-dimethylacetamide (DMAc) with
mechanical agitation assistance. After complete dilution, followed by
slow evaporation of the solvent at 60°C, the samples were dried.
Films of about 80 μm were obtained. FTIR and UV-Vis
spectroscopic techniques were used to characterize the
nanocomposites. The appearance of absorption bands in the FTIR
spectra of nanofilled samples, when compared to the spectrum of
pristine PVDF samples, are discussed and compared with the UV-Vis
measurements.
Abstract: This paper investigates the effects of breaks in bonds,
breaks in the earthing system and breaks in earth wire on the rise of
the earth potential (EPR) in a substation and at the transmission tower
bases using various models of an L6 tower. Different approaches
were adopted to examine the integrity of the earthing system and the
terminal towers. These effects were investigated to see the associated
difference in the EPR magnitudes with respect to a healthy system at
various locations. Comparisons of the computed EPR magnitudes
were then made between the healthy and unhealthy system to detect
any difference. The studies were conducted at power frequency for a
uniform soil with different soil resistivities. It was found that full
breaks in the double bond of the terminal towers increase the EPR
significantly at the fault location, while they reduce EPR at the
terminal tower bases. A fault on the isolated section of the grid can
result in EPR values up to 8 times of those on a healthy system at
higher soil resistivities, provided that the extended earthing system
stays connected to the grid.
Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: A university-wide survey to obtain baseline data
regarding the perceptions of key terms related to e-learning and
distance learning among students, faculty and staff was conducted to
help achieve the goals of Princess Nourah bint Abdulrahman
University’s and the Kingdom of Saudi Arabia’s National Center for
e-learning and Distance Learning. This paper comprises a relevant
literature review, the survey methodology, preliminary data analysis,
discussion, and recommendations for further research. The major
findings indicate a deep and wide differentiation of understanding
among users of critical key terms.
Abstract: Wireless sensors, also known as wireless sensor nodes,
have been making a significant impact on human daily life. The
Radio Frequency Identification (RFID) and Wireless Sensor Network
(WSN) are two complementary technologies; hence, an integrated
implementation of these technologies expands the overall
functionality in obtaining long-range and real-time information on the
location and properties of objects and people. An approach for
integrating ZigBee and RFID networks is proposed in this paper, to
create an energy-efficient network improved by the benefits of
combining ZigBee and RFID architecture. Furthermore, the
compatibility and requirements of the ZigBee device and
communication links in the typical RFID system which is presented
with the real world experiment on the capabilities of the proposed
RFID system.
Abstract: Growth and remodeling of biological structures have
gained lots of attention over the past decades. Determining the
response of living tissues to mechanical loads is necessary for a wide
range of developing fields such as prosthetics design or computerassisted
surgical interventions. It is a well-known fact that biological
structures are never stress-free, even when externally unloaded. The
exact origin of these residual stresses is not clear, but theoretically,
growth is one of the main sources. Extracting body organ’s shapes
from medical imaging does not produce any information regarding
the existing residual stresses in that organ. The simplest cause of such
stresses is gravity since an organ grows under its influence from
birth. Ignoring such residual stresses might cause erroneous results in
numerical simulations. Accounting for residual stresses due to tissue
growth can improve the accuracy of mechanical analysis results. This
paper presents an original computational framework based on gradual
growth to determine the residual stresses due to growth. To illustrate
the method, we apply it to a finite element model of a healthy human
face reconstructed from medical images. The distribution of residual
stress in facial tissues is computed, which can overcome the effect of
gravity and maintain tissues firmness. Our assumption is that tissue
wrinkles caused by aging could be a consequence of decreasing
residual stress and thus not counteracting gravity. Taking into
account these stresses seems therefore extremely important in
maxillofacial surgery. It would indeed help surgeons to estimate
tissues changes after surgery.
Abstract: Mumbai, being traditionally the epicenter of India's
trade and commerce, the existing major ports such as Mumbai and
Jawaharlal Nehru Ports (JN) situated in Thane estuary are also
developing its waterfront facilities. Various developments over the
passage of decades in this region have changed the tidal flux
entering/leaving the estuary. The intake at Pir-Pau is facing the
problem of shortage of water in view of advancement of shoreline,
while jetty near Ulwe faces the problem of ship scheduling due to
existence of shallower depths between JN Port and Ulwe Bunder. In
order to solve these problems, it is inevitable to have information
about tide levels over a long duration by field measurements.
However, field measurement is a tedious and costly affair;
application of artificial intelligence was used to predict water levels
by training the network for the measured tide data for one lunar tidal
cycle. The application of two layered feed forward Artificial Neural
Network (ANN) with back-propagation training algorithms such as
Gradient Descent (GD) and Levenberg-Marquardt (LM) was used to
predict the yearly tide levels at waterfront structures namely at Ulwe
Bunder and Pir-Pau. The tide data collected at Apollo Bunder, Ulwe,
and Vashi for a period of lunar tidal cycle (2013) was used to train,
validate and test the neural networks. These trained networks having
high co-relation coefficients (R= 0.998) were used to predict the tide
at Ulwe, and Vashi for its verification with the measured tide for the
year 2000 & 2013. The results indicate that the predicted tide levels
by ANN give reasonably accurate estimation of tide. Hence, the
trained network is used to predict the yearly tide data (2015) for
Ulwe. Subsequently, the yearly tide data (2015) at Pir-Pau was
predicted by using the neural network which was trained with the
help of measured tide data (2000) of Apollo and Pir-Pau. The analysis of measured data and study reveals that: The
measured tidal data at Pir-Pau, Vashi and Ulwe indicate that there is
maximum amplification of tide by about 10-20 cm with a phase lag
of 10-20 minutes with reference to the tide at Apollo Bunder
(Mumbai). LM training algorithm is faster than GD and with increase
in number of neurons in hidden layer and the performance of the
network increases. The predicted tide levels by ANN at Pir-Pau and
Ulwe provides valuable information about the occurrence of high and
low water levels to plan the operation of pumping at Pir-Pau and
improve ship schedule at Ulwe.
Abstract: Open jet testing is a valuable testing technique which
provides the desired results with reasonable accuracy. It has been
used in past for the airships and now has recently been applied for the
hybrid ones, having more non-buoyant force coming from the wings,
empennage and the fuselage. In the present review work, an effort
has been done to review the challenges involved in open jet testing.
In order to shed light on the application of this technique, the
experimental results of two different configurations are presented.
Although, the aerodynamic results of such vehicles are unique to its
own design; however, it will provide a starting point for planning any
future testing. Few important testing areas which need more attention
are also highlighted. Most of the hybrid buoyant aerial vehicles are
unconventional in shape and there experimental data is generated,
which is unique to its own design.
Abstract: The process of human resources management in the structures of corporate groups demonstrates certain specificity, resulting from the division of decision-making and executive competencies, which occurs within these structures between a parent company and its subsidiaries. The subprocess of employee assessment is considered crucial, since it provides information for the implementation of personnel function. The empirical studies conducted in corporate groups, within which at least one company is located in Poland, confirmed the critical significance of employee assessment systems in the process of human resources management in corporate groups. Parent companies, most often, retain their decision-making authority within the framework of the discussed process and introduce uniform employee assessment and personnel controlling systems to subsidiary companies. However, the instruments for employee assessment applied in corporate groups do not present such specificity.
Abstract: In this paper, the regression dependence of dancing
intensity from wind speed and length of span was established due to
the statistic data obtained from multi-year observations on line wires
dancing accumulated by power systems of Kazakhstan and the
Russian Federation. The lower and upper limitations of the equations
parameters were estimated, as well as the adequacy of the regression
model. The constructed model will be used in research of dancing
phenomena for the development of methods and means of protection
against dancing and for zoning plan of the territories of line wire
dancing.
Abstract: An analysis of the air tightness level is performed on a representative sample of school classrooms in Southern Spain, which allows knowing the infiltration level of these classrooms, mainly through its envelope, which can affect both energy demand and occupant's thermal comfort. By using a pressurization/depressurization equipment (Blower-Door test), a characterization of 45 multipurpose classrooms have been performed in nine non-university educational institutions of the main climate zones of Southern Spain. In spite of having two doors and a high ratio between glass surface and outer surface, it is possible to see in these classrooms that there is an adequate level of airtightness, since all the n50 values obtained are lower than 9.0 ACH, with an average value around 7.0 ACH.
Abstract: 21st century has transformed the labor market
landscape in a way of posing new and different demands on
university graduates as well as university lecturers, which means that
the knowledge and academic skills students acquire in the course of
their studies should be applicable and transferable from the higher
education context to their future professional careers. Given the
context of the Languages for Specific Purposes (LSP) classroom, the
teachers’ objective is not only to teach the language itself, but also to
prepare students to use that language as a medium to develop generic
skills and competences. These include media and information
literacy, critical and creative thinking, problem-solving and analytical
skills, effective written and oral communication, as well as
collaborative work and social skills, all of which are necessary to
make university graduates more competitive in everyday professional
environments. On the other hand, due to limitations of time and large
numbers of students in classes, the frequently topic-centered syllabus
of LSP courses places considerable focus on acquiring the subject
matter and specialist vocabulary instead of sufficient development of
skills and competences required by students’ prospective employers.
This paper intends to explore some of those issues as viewed both by
LSP lecturers and by business professionals in their respective
surveys. The surveys were conducted among more than 50 LSP
lecturers at higher education institutions in Croatia, more than 40 HR
professionals and more than 60 university graduates with degrees in
economics and/or business working in management positions in
mainly large and medium-sized companies in Croatia. Various elements of LSP course content have been taken into
consideration in this research, including reading and listening
comprehension of specialist texts, acquisition of specialist vocabulary
and grammatical structures, as well as presentation and negotiation
skills. The ability to hold meetings, conduct business correspondence,
write reports, academic texts, case studies and take part in debates
were also taken into consideration, as well as informal business
communication, business etiquette and core courses delivered in a
foreign language. The results of the surveys conducted among LSP
lecturers will be analyzed with reference to what extent those
elements are included in their courses and how consistently and
thoroughly they are evaluated according to their course requirements.
Their opinions will be compared to the results of the surveys
conducted among professionals from a range of industries in Croatia
so as to examine how useful and important they perceive the same
elements of the LSP course content in their working environments.
Such comparative analysis will thus show to what extent the syllabi
of LSP courses meet the demands of the employment market when it
comes to the students’ language skills and competences, as well as
transferable skills. Finally, the findings will also be compared to the
observations based on practical teaching experience and the relevant
sources that have been used in this research. In conclusion, the ideas and observations in this paper are merely
open-ended questions that do not have conclusive answers, but might
prompt LSP lecturers to re-evaluate the content and objectives of
their course syllabi.
Abstract: The application of recycle waste tires into civil
engineering practices, namely asphalt paving mixtures and cementbased
materials has been gaining ground across the world. This
review summarizes and compares the recent achievements in the area
of plain rubberized concrete (PRC), in details. Different treatment
methods have been discussed to improve the performance of
rubberized Portland cement concrete. The review also includes the
effects of size and amount of tire rubbers on mechanical and
durability properties of PRC. The microstructure behaviour of the
rubberized concrete was detailed.
Abstract: Tourism can do a great deal of good in destinations,
whether it be by bringing economic benefits to local communities,
helping with conservation efforts or in placing a value on aspects of
cultural heritage. As responsive travelers, we must all try to do more
of the good and less of the negative. This is simply description of the
sustainable tourism. This paper aims to set some criteria of successful
sustainable tourism development and then through these criteria
analyzing the development of some resorts in Egypt known as
sustainable resorts. Hence, a comprehensive improvement of the
touristic areas is certainly needed to ensure a successful sustainable
tourism development radiated the sense of uniformity and coherence.
Egypt can benefit from these criteria to develop its resorts in order to
preserve and revitalize its unique natural character and achieve mixed
uses and tourism development.
Abstract: In this research, students’ scientific attitude, computer anxiety, educational use of the Internet, academic achievement, and problematic use of the Internet are analyzed based on different variables (gender, parents’ educational level and daily access to the Internet). The research group involves 361 students from two middle schools which are located in the center of Konya. The “general survey method” is adopted in the research. In accordance with the purpose of the study, percentage, mean, standard deviation, independent samples t--‐test, ANOVA (variance) are employed in the study. A total of four scales are implemented. These four scales include a total of 13 sub-dimensions. The scores from these scales and their subscales are studied in terms of various variables. In the research, students’ scientific attitude, computer anxiety, educational use of the Internet, the problematic Internet use and academic achievement (gender, parent educational level, and daily access to the Internet) are investigated based on various variables and some significant relations are found.
Abstract: In the aviation industry, many faults may occur frequently during the maintenance processes and assembly operations of complex structured aircrafts because of their high dependencies of components. These faults affect the quality of aircraft parts or developed modules adversely. Technical employee requires long time and high labor force while checking the correctness of each component. In addition, the person must be trained regularly because of the ever-growing and changing technology. Generally, the cost of this training is very high. Augmented Reality (AR) technology reduces the cost of training radically and improves the effectiveness of the training. In this study, the usage of AR technology in the aviation industry has been investigated and the effectiveness of AR with heads-up display glasses has been examined. An application has been developed for comparison of production process with AR and manual one.
Abstract: Thoracotomy is a great surgery that has serious pulmonary complications, so purpose of this study was to determine the response of diaphragmatic excursion to inspiratory muscle trainer post thoracotomy. Thirty patients of both sexes (16 men and 14 women) with age ranged from 20 to 40 years old had done thoracotomy participated in this study. The practical work was done in cardiothoracic department, Kasr-El-Aini hospital at faculty of medicine for individuals 3 days Post operatively. Patients were assigned into two groups: group A (study group) included 15 patients (8 men and 7 women) who received inspiratory muscle training by using inspiratory muscle trainer for 20 minutes and routine chest physiotherapy (deep breathing, cough and early ambulation) twice daily, 3 days per week for one month. Group B (control group) included 15 patients (8 men and 7 women) who received the routine chest physiotherapy only (deep breathing, cough and early ambulation) twice daily, 3 days per week for one month. Ultrasonography was used to evaluate the changes in diaphragmatic excursion before and after training program. Statistical analysis revealed a significant increase in diaphragmatic excursion in the study group (59.52%) more than control group (18.66%) after using inspiratory muscle trainer post operatively in patients post thoracotomy. It was concluded that the inspiratory muscle training device increases diaphragmatic excursion in patients post thoracotomy through improving inspiratory muscle strength and improving mechanics of breathing and using of inspiratory muscle trainer as a method of physical therapy rehabilitation to reduce post-operative pulmonary complications post thoracotomy.
Abstract: The aim of irrigation is to recharge the available water
in the soil. Quality of irrigation water is essential for the yield and
quality of crops produced, maintenance of soil productivity and
protection of the environment. The analysis of irrigation water arises
as a need to know the impact of irrigation water on the yield of crops,
the effect, and the necessary control measures to rectify the effect of
this for optimum production and yield of crops. This study was conducted to assess the quality of irrigation water
with its performance on crop planted, in Josepdam irrigation scheme
Bacita, Nigeria. Field visits were undertaken to identify and locate
water supply sources and collect water samples from these sources;
X1 Drain, Oshin, River Niger loop and Ndafa. Laboratory
experiments were then undertaken to determine the quality of raw
water from these sources. The analysis was carried for various parameters namely; physical
and chemical analyses after water samples have been taken from four
sources. The samples were tested in laboratory. Results showed that
the raw water sources shows no salinity tendencies with SAR values
less than 1me/l and Ecvaules at Zero while the pH were within the
recommended range by FAO, there are increase in potassium and
sulphate content contamination in three of the location. From this, it
is recommended that there should be proper monitoring of the
scheme by conducting analysis of water and soil in the environment,
preferable test should be carried out at least one year to cover the
impact of seasonal variations and to determine the physical and
chemical analysis of the water used for irrigation at the scheme.
Abstract: This paper describes an ab-initio design, development and calibration results of an Optical Sensor Ground Reaction Force Measurement Platform (OSGRFP) for gait and geriatric studies. The developed system employs an array of FBG sensors to measure the respective ground reaction forces from all three axes (X, Y and Z), which are perpendicular to each other. The novelty of this work is two folded. One is in its uniqueness to resolve the tri axial resultant forces during the stance in to the respective pure axis loads and the other is the applicability of inherently advantageous FBG sensors which are most suitable for biomechanical instrumentation. To validate the response of the FBG sensors installed in OSGRFP and to measure the cross sensitivity of the force applied in other directions, load sensors with indicators are used. Further in this work, relevant mathematical formulations are presented for extracting respective ground reaction forces from wavelength shifts/strain of FBG sensors on the OSGRFP. The result of this device has implications in understanding the foot function, identifying issues in gait cycle and measuring discrepancies between left and right foot. The device also provides a method to quantify and compare relative postural stability of different subjects under test, which has implications in post-surgical rehabilitation, geriatrics and optimizing training protocols for sports personnel.