Abstract: Extraction of lactic acid by emulsion liquid membrane technology (ELM) using n-trioctyl amine (TOA) in n-heptane as carrier within the organic membrane along with sodium carbonate as acceptor phase was optimized by using response surface methodology (RSM). A three level Box-Behnken design was employed for experimental design, analysis of the results and to depict the combined effect of five independent variables, vizlactic acid concentration in aqueous phase (cl), sodium carbonate concentration in stripping phase (cs), carrier concentration in membrane phase (ψ), treat ratio, and batch extraction time (τ)
with equal volume of organic and external aqueous phase on lactic acid extraction efficiency. The maximum lactic acid extraction efficiency (ηext) of 98.21%from aqueous phase in a batch reactor using ELM was found at the optimized values for test variables, cl, cs, ψ, and τ as 0.06 [M], 0.18 [M], 4.72 (%,v/v), 1.98 (v/v) and 13.36 min respectively.
Abstract: The objective of this work is to produce heterotrophic
microalgal lipid in flask-batch fermentation. Chlorella sp. KKU-S2
supported maximum values of 0.374 g/L/d, 0.478 g lipid/g cells, and
0.112 g/L/d for volumetric lipid production rate, and specific yield of
lipid, and specific rate of lipid production, respectively when culture
was performed on BG-11 medium supplemented with 50g/L glucose.
Among the carbon sources tested, maximum cell yield coefficient
(YX/S, g/L), maximum specific yield of lipid (YP/X, g lipid/g cells) and
volumetric lipid production rate (QP, g/L/d) were found of 0.728,
0.237, and 0.619, respectively, using sugarcane molasses as carbon
source. The main components of fatty acid from extracted lipid were
palmitic acid, stearic acid, oleic acid and linoleic acid which similar
to vegetable oils and suitable for biodiesel production.
Abstract: Sexual behavior and semen charactertistics were
evaluated in young male Boer goats in tropical condition during time
period of September to November 2009. The animal was let to have
adaptation for five months after importation from Australian climate.
A total of 20 bucks were observed for sexual behavior and ability of
semen production. Out of this number, 4 faild to libido and 3
produced poor semen. The remaing 13 animals were divided into
three groups according to the ages (11-13, 15-16 and 18-25 months).
Sexual behavior consisting response time to female teaser,
ejaculation time, fixing strenght to female and erection status were
normaly observer in 13 bucks, and there was no significant difference
between age groups. Semen characteristics from 13 bucks were in
normal quality in the volume, sperm mass motility, individual
motility, percentage of live- and abnormal sperm. We concluded that
is possible to collect semen of Boer goats during the period of
September to November under tropical condition. Collection during
other time period should be analyzed.
Abstract: An automatic method for the extraction of feature points for face based applications is proposed. The system is based upon volumetric feature descriptors, which in this paper has been extended to incorporate scale space. The method is robust to noise and has the ability to extract local and holistic features simultaneously from faces stored in a database. Extracted features are stable over a range of faces, with results indicating that in terms of intra-ID variability, the technique has the ability to outperform manual landmarking.
Abstract: Saccharomyces cerevisiae (baker-s yeast) can exhibit
sustained oscillations during the operation in a continuous bioreactor
that adversely affects its stability and productivity. Because of
heterogeneous nature of cell populations, the cell population balance
models can be used to capture the dynamic behavior of such cultures.
In this paper an unstructured, segregated model is used which is
based on population balance equation(PBE) and then in order to
simulation, the 4th order Rung-Kutta is used for time dimension and
three methods, finite difference, orthogonal collocation on finite
elements and Galerkin finite element are used for discretization of the
cell mass domain. The results indicate that the orthogonal collocation
on finite element not only is able to predict the oscillating behavior of
the cell culture but also needs much little time for calculations.
Therefore this method is preferred in comparison with other methods.
In the next step two controllers, a globally linearizing control (GLC)
and a conventional proportional-integral (PI) controller are designed
for controlling the total cell mass per unit volume, and performances
of these controllers are compared through simulation. The results
show that although the PI controller has simpler structure, the GLC
has better performance.
Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: Positron emission particle tracking (PEPT) is a
technique in which a single radioactive tracer particle can be
accurately tracked as it moves. A limitation of PET is that in order to
reconstruct a tomographic image it is necessary to acquire a large
volume of data (millions of events), so it is difficult to study rapidly
changing systems. By considering this fact, PEPT is a very fast
process compared with PET.
In PEPT detecting both photons defines a line and the annihilation
is assumed to have occurred somewhere along this line. The location
of the tracer can be determined to within a few mm from coincident
detection of a small number of pairs of back-to-back gamma rays and
using triangulation. This can be achieved many times per second and
the track of a moving particle can be reliably followed. This
technique was invented at the University of Birmingham [1].
The attempt in PEPT is not to form an image of the tracer particle
but simply to determine its location with time. If this tracer is
followed for a long enough period within a closed, circulating system
it explores all possible types of motion.
The application of PEPT to industrial process systems carried out
at the University of Birmingham is categorized in two subjects: the
behaviour of granular materials and viscous fluids. Granular
materials are processed in industry for example in the manufacture of
pharmaceuticals, ceramics, food, polymers and PEPT has been used
in a number of ways to study the behaviour of these systems [2].
PEPT allows the possibility of tracking a single particle within the
bed [3]. Also PEPT has been used for studying systems such as: fluid
flow, viscous fluids in mixers [4], using a neutrally-buoyant tracer
particle [5].
Abstract: Electro-optical devices are increasingly used for
military sea-, land- and air applications to detect, recognize and track
objects. Typically, these devices produce video information that is
presented to an operator. However, with increasing availability of
electro-optical devices the data volume is becoming very large,
creating a rising need for automated analysis. In a military setting,
this typically involves detecting and recognizing objects at a large
distance, i.e. when they are difficult to distinguish from background
and noise. One may consider combining multiple images from a
video stream into a single enhanced image that provides more
information for the operator. In this paper we investigate a simple
algorithm to enhance simulated images from a military context and
investigate how the enhancement is affected by various types of
disturbance.
Abstract: This paper investigates experimentally and
analytically the torsion behavior of steel fibered high strength self
compacting concrete beams reinforced by GFRP bars. Steel fibered
high strength self compacting concrete (SFHSSCC) and GFRP bars
became in the recent decades a very important materials in the
structural engineering field. The use of GFRP bars to replace steel
bars has emerged as one of the many techniques put forward to
enhance the corrosion resistance of reinforced concrete structures.
High strength concrete and GFRP bars attract designers and
architects as it allows improving the durability as well as the esthetics
of a construction. One of the trends in SFHSSCC structures is to
provide their ductile behavior and additional goal is to limit
development and propagation of macro-cracks in the body of
SFHSSCC elements. SFHSSCC and GFRP bars are tough, improve
the workability, enhance the corrosion resistance of reinforced
concrete structures, and demonstrate high residual strengths after
appearance of the first crack. Experimental studies were carried out
to select effective fiber contents. Three types of volume fraction from
hooked shape steel fibers are used in this study, the hooked steel
fibers were evaluated in volume fractions ranging between 0.0%,
0.75% and 1.5%. The beams shape is chosen to create the required
forces (i.e. torsion and bending moments simultaneously) on the test
zone. A total of seven beams were tested, classified into three groups.
All beams, have 200cm length, cross section of 10×20cm,
longitudinal bottom reinforcement of 3
Abstract: Thermal water hammer is a special type of water
hammer which rarely occurs in heat exchangers. In biphasic fluids, if
steam bubbles are surrounded by condensate, regarding lower
condensate temperature than steam, they will suddenly collapse. As a
result, the vacuum caused by an extreme change in volume lead to
movement of the condensates in all directions and their collision the
force produced by this collision leads to a severe stress in the pipe
wall. This phenomenon is a special type of water hammer. According
to fluid mechanics, this phenomenon is a particular type of transient
flows during which abrupt change of fluid leads to sudden pressure
change inside the tube. In this paper, the mechanism of abrupt failure
of 80 tubes of 481 tubes of a methanol heat exchanger is discussed.
Initially, due to excessive temperature differences between heat
transfer fluids and simultaneous failure of 80 tubes, thermal shock
was presupposed as the reason of failure. Deeper investigation on
cross-section of failed tubes showed that failure was, ductile type of
failure, so the first hypothesis was rejected. Further analysis and more
accurate experiments revealed that failure of tubes caused by thermal
water hammer. Finally, the causes of thermal water hammer and
various solutions to avoid such mechanism are discussed.
Abstract: In this study, an experimental investigation was carried
out to fix CO2 into the electronic arc furnace (EAF) reducing slag from
stainless steelmaking process under wet grinding. The slag was ground
by the vibrating ball mill with the CO2 and pure water. The reaction
behavior was monitored with constant pressure method, and the
change of CO2 volume in the experimental system with grinding time
was measured. It was found that the CO2 absorption occurred as soon
as the grinding started. The CO2 absorption under wet grinding was
significantly larger than that under dry grinding. Generally, the
amount of CO2 absorption increased as the amount of water, the
amount of slag, the diameter of alumina ball and the initial pressure of
CO2 increased. However, the initial absorption rate was scarcely
influenced by the experimental conditions except for the initial CO2
pressure. According to this research, the CO2 reacted with the CaO
inside the slag to form CaCO3.
Abstract: Polyurethane foam (PUF) is formed by a chemical
reaction of polyol and isocyanate. The aim is to understand the
impact of Silicone on synthesizing polyurethane in differentiate
volume of molding. The method used was one step process, which is
simultaneously caried out a blending polyol (petroleum polyol and
soybean polyol), a TDI (2,4):MDI (4,4-) (80:20), a distilled water,
and a silicone. The properties of the material were measured via a
number of parameters, which are polymer density, compressive
strength, and cellular structures. It is found that density of
polyurethane using silicone with volume of molding either 250 ml or
500 ml is lower than without using silicone.
Abstract: ORC (Organic Rankine Cycle) has potential of
reducing consumption of fossil fuels and has many favorable
characteristics to exploit low-temperature heat sources. In this work
thermodynamic performance of ORC with regeneration is
comparatively assessed for various working fluids. Special attention is
paid to the effects of system parameters such as the turbine inlet
pressure on the characteristics of the system such as net work
production, heat input, volumetric flow rate per 1 MW of net work and
quality of the working fluid at turbine exit as well as thermal
efficiency. Results show that for a given source the thermal efficiency
generally increases with increasing of the turbine inlet pressure
however has optimal condition for working fluids of low critical
pressure such as iso-pentane or n-pentane.
Abstract: The aim of this study was to synthesize the single
walled carbon nanotubes (SWCNTs) and determine their hydrogen
storage capacities. SWCNTs were firstly synthesized by chemical
vapor deposition (CVD) of acetylene (C2H2) on a magnesium oxide
(MgO) powder impregnated with an iron nitrate (Fe(NO3)3·9H2O)
solution. The synthesis parameters were selected as: the synthesis
temperature of 800°C, the iron content in the precursor of 5% and the
synthesis time of 30 min. Purification process of SWCNTs was
fulfilled by microwave digestion at three different temperatures (120,
150 and 200 °C), three different acid concentrations (0.5, 1 and 1.5
M) and for three different time intervals (15, 30 and 60 min). Nitric
acid (HNO3) was used in the removal of the metal catalysts. The
hydrogen storage capacities of the purified materials were measured
using volumetric method at the liquid nitrogen temperature and gas
pressure up to 100 bar. The effects of the purification conditions such
as temperature, time and acid concentration on hydrogen adsorption
were investigated.
Abstract: The effect of Alumina nanoparticle size on thermophysical
properties, heat transfer performance and pressure loss characteristics of
Aviation Turbine Fuel (ATF)-Al2O3 nanofluids is studied experimentally for
the proposed application of regenerative cooling of semi-cryogenic rocket
engine thrust chambers. Al2O3 particles with mean diameters of 50 nm or 150
nm are dispersed in ATF. At 500C and 0.3% particle volume concentration,
the bigger particles show increases of 17% in thermal conductivity and 55% in
viscosity, whereas the smaller particles show corresponding increases of 21%
and 22% for thermal conductivity and viscosity respectively. Contrary to these
results, experiments to study the heat transfer performance and pressure loss
characteristics show that at the same pumping power, the maximum
enhancement in heat transfer coefficient at 500C and 0.3% concentration is
approximately 47% using bigger particles, whereas it is only 36% using
smaller particles.
Abstract: Use of fly ash as a supplementary cementing material
in large volumes can bring both technological and economic benefits
for concrete industry. In this investigation mix proportions for high
volume fly ash concrete were determined at cement replacement
levels of 50%, 55%, 60% and 65% with low calcium fly ash. Flexural
and compressive strengths of different mixes were measured at ages
of 7, 28 and 90 days. Flexural strength of composite section prepared
from pavement quality and lean high volume fly ash concrete was
determined at the age of 28 days. High volume fly ash concrete mixes
exhibited higher rate of strength gain and age factors than
corresponding reference concrete mixes. The optimum cement
replacement level for pavement quality concrete was found to be
60%. The consideration of bond between pavement quality and lean
of high volume fly ash concrete will be beneficial in design of rigid
pavements.
Abstract: In this study, direct numerical simulation for the bubble condensation in the subcooled boiling flow was performed. The main goal was to develop the CFD modeling for the bubble condensation and to evaluate the accuracy of the VOF model with the developed CFD modeling. CFD modeling for the bubble condensation was developed by modeling the source terms in the governing equations of VOF model using UDF. In the modeling, the amount of condensation was determined using the interfacial heat transfer coefficient obtained from the bubble velocity, liquid temperature and bubble diameter every time step. To evaluate the VOF model using the CFD modeling for the bubble condensation, CFD simulation results were compared with SNU experimental results such as bubble volume and shape, interfacial area, bubble diameter and bubble velocity. Simulation results predicted well the behavior of the actual condensing bubble. Therefore, it can be concluded that the VOF model using the CFD modeling for the bubble condensation will be a useful computational fluid dynamics tool for analyzing the behavior of the condensing bubble in a wide range of the subcooled boiling flow.
Abstract: A Finite Volume method based on Characteristic Fluxes for compressible fluids is developed. An explicit cell-centered resolution is adopted, where second and third order accuracy is provided by using two different MUSCL schemes with Minmod, Sweby or Superbee limiters for the hyperbolic part. Few different times integrator is used and be describe in this paper. Resolution is performed on a generic unstructured Cartesian grid, where solid boundaries are handled by a Cut-Cell method. Interfaces are explicitely advected in a non-diffusive way, ensuring local mass conservation. An improved cell cutting has been developed to handle boundaries of arbitrary geometrical complexity. Instead of using a polygon clipping algorithm, we use the Voxel traversal algorithm coupled with a local floodfill scanline to intersect 2D or 3D boundary surface meshes with the fixed Cartesian grid. Small cells stability problem near the boundaries is solved using a fully conservative merging method. Inflow and outflow conditions are also implemented in the model. The solver is validated on 2D academic test cases, such as the flow past a cylinder. The latter test cases are performed both in the frame of the body and in a fixed frame where the body is moving across the mesh. Adaptive Cartesian grid is provided by Paramesh without complex geometries for the moment.
Abstract: The effect of streamwise conduction on the thermal
characteristics of forced convection for nanofluidic flow in
rectangular microchannel heat sinks under isothermal wall has been
investigated. By applying the fin approach, models with and without
streamwise conduction term in the energy equation were developed
for hydrodynamically and thermally fully-developed flow. These two
models were solved to obtain closed form analytical solutions for the
nanofluid and solid wall temperature distributions and the analysis
emphasized details of the variations induced by the streamwise
conduction on the nanofluid heat transport characteristics. The effects
of the Peclet number, nanoparticle volume fraction, thermal
conductivity ratio on the thermal characteristics of forced convection
in microchannel heat sinks are analyzed. Due to the anomalous
increase in the effective thermal conductivity of nanofluid compared
to its base fluid, the effect of streamwise conduction is expected to be
more significant. This study reveals the significance of the effect of
streamwise conduction under certain conditions of which the
streamwise conduction should not be neglected in the forced
convective heat transfer analysis of microchannel heat sinks.
Abstract: The effects of global warming on India vary from the
submergence of low-lying islands and coastal lands to the melting of
glaciers in the Indian Himalayas, threatening the volumetric flow rate
of many of the most important rivers of India and South Asia. In
India, such effects are projected to impact millions of lives. As a
result of ongoing climate change, the climate of India has become
increasingly volatile over the past several decades; this trend is
expected to continue.
Climate change is one of the most important global environmental
challenges, with implications for food production, water supply,
health, energy, etc. Addressing climate change requires a good
scientific understanding as well as coordinated action at national and
global level. The climate change issue is part of the larger challenge
of sustainable development. As a result, climate policies can be more
effective when consistently embedded within broader strategies
designed to make national and regional development paths more
sustainable. The impact of climate variability and change, climate
policy responses, and associated socio-economic development will
affect the ability of countries to achieve sustainable development
goals.
A very well calibrated Soil and Water Assessment Tool (R2 =
0.9968, NSE = 0.91) was exercised over the Khatra sub basin of the
Kangsabati River watershed in Bankura district of West Bengal,
India, in order to evaluate projected parameters for agricultural
activities. Evapotranspiration, Transmission Losses, Potential
Evapotranspiration and Lateral Flow to reach are evaluated from the
years 2041-2050 in order to generate a picture for sustainable
development of the river basin and its inhabitants.
India has a significant stake in scientific advancement as well as
an international understanding to promote mitigation and adaptation.
This requires improved scientific understanding, capacity building,
networking and broad consultation processes. This paper is a
commitment towards the planning, management and development of
the water resources of the Kangsabati River by presenting detailed
future scenarios of the Kangsabati river basin, Khatra sub basin, over
the mentioned time period.
India-s economy and societal infrastructures are finely tuned to the
remarkable stability of the Indian monsoon, with the consequence
that vulnerability to small changes in monsoon rainfall is very high.
In 2002 the monsoon rains failed during July, causing profound loss
of agricultural production with a drop of over 3% in India-s GDP.
Neither the prolonged break in the monsoon nor the seasonal rainfall
deficit was predicted. While the general features of monsoon
variability and change are fairly well-documented, the causal
mechanisms and the role of regional ecosystems in modulating the
changes are still not clear. Current climate models are very poor at
modelling the Asian monsoon: this is a challenging and critical
region where the ocean, atmosphere, land surface and mountains all
interact. The impact of climate change on regional ecosystems is
likewise unknown. The potential for the monsoon to become more
volatile has major implications for India itself and for economies
worldwide. Knowledge of future variability of the monsoon system,
particularly in the context of global climate change, is of great
concern for regional water and food security.
The major findings of this paper were that of all the chosen
projected parameters, transmission losses, soil water content,
potential evapotranspiration, evapotranspiration and lateral flow to
reach, display an increasing trend over the time period of years 2041-
2050.