Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: The aim of the present investigation was to compare
sex differences in thyroid gland structure of rabbits. Five adult male
and five adult female (3.1-3.5 kg body weight) New Zealand white
rabbits were used in the experiment. Results showed that at light
microscopic level, there was no sex difference in microscopic
appearance of the thyroid glands. At electron microscopic level,
however, the mitochondria and the microvilli of the follicular cells
are more numerous and the Golgi complex is also more extensive in
male rabbits in comparison to females. Results obtained from
micrometric measurements showed that the volume density of the
follicles is higher in males than in females, but the differences are not
statistically significant .The volume density of epithelium and the
height of follicular cells are significantly greater in males than in
females and reverse is true about the volume density of interstitium
(p
Abstract: As a part of routine oesophageal HDR Brachytherapy procedure, treatment planning takes about 45 minutes while patients are under light sedation. Some patients may suffer gagging and/or spasms before the 90-minute brachytherapy procedure complete, and the treatment may need to be aborted. A pre-prepared plan generated before patient’s sedation may reduce the brachytherapy procedure time by 40 minutes. This paper reports rationality and evidence of pre-prepared treatment plans. A retrospective study of 28 patients confirms that pre-prepared plans would be acceptable for all reviewed patients. The rationality is further confirmed by a systemic study with a wide range of applicator curvature and treatment volume. Detailed comparison between CT based treatment plans and pre-prepared plans are discussed. The argument holds for endobronchial HDR brachytherapy too. With the above evidence, pre-prepared plans have been used for all oesophageal and endobronchial HDR brachytherapy cases in our clinic.
Abstract: In order to investigate a PROX microreactor
performance, two-dimensional modeling of the reacting flow
between two parallel plates is performed through a finite volume
method using an improved SIMPLE algorithm. A three-step surface
kinetics including hydrogen oxidation, carbon monoxide oxidation
and water-gas shift reaction is applied for a Pt-Fe/γ-Al2O3 catalyst
and operating temperatures of about 100ºC. Flow pattern, pressure
field, temperature distribution, and mole fractions of species are
found in the whole domain for all cases. Also, the required reactive
length for removing carbon monoxide from about 2% to less than 10
ppm is found. Furthermore, effects of hydraulic diameter, wall
temperature, and inlet mole fraction of air and water are investigated
by considering carbon monoxide selectivity and conversion. It is
found that air and water addition may improve the performance of
the microreactor in carbon monoxide removal in such operating
conditions; this is in agreement with the pervious published results.
Abstract: In pressure vessels contain hydrogen, the role of
hydrogen will be important because of hydrogen cracking problem. It
is difficult to predict what is happened in metallurgical field spite of a
lot of studies have been searched. The main role in controlling the
mass diffusion as driving force is related to stress. In this study, finite
element analysis is implemented to estimate material-s behavior
associated with hydrogen embrittlement. For this purpose, one model
of a pressure vessel is introduced that it has definite boundary and
initial conditions. In fact, finite element is employed to solve the
sequentially coupled mass diffusion with stress near a crack front in a
pressure vessel. Modeling simulation intergrarnular fracture of AISI
4135 steel due to hydrogen is investigated. So, distribution of
hydrogen and stress are obtained and they indicate that their
maximum amounts occur near the crack front. This phenomenon is
happened exactly the region between elastic and plastic field.
Therefore, hydrogen is highly mobile and can diffuse through crystal
lattice so that this zone is potential to trap high volume of hydrogen.
Consequently, crack growth and fast fracture will be happened.
Abstract: The effects of upflow liquid velocity (ULV) on
performance of expanded granular sludge bed (EGSB) system were
investigated. The EGSB reactor, made from galvanized steel pipe
0.10 m diameter and 5 m height, had been used to treat piggery
wastewater, after passing through acidification tank. It consisted of
39.3 l working volume in reaction zone and 122 l working volume in
sedimentation zone, at the upper part. The reactor was seeded with
anaerobically digested sludge and operated at the ULVs of 4, 8, 12
and 16 m/h, consecutively, corresponding to organic loading rates of
9.6 – 13.0 kg COD/ (m3.d). The average COD concentrations in the
influent were 9,601 – 13,050 mg/l. The COD removal was not
significantly different, i.e. 93.0% - 94.0%, except at ULV 12 m/h where
SS in the influent was exceptionally high so that VSS washout had
occurred, leading to low COD removal. The FCOD and VFA
concentrations in the effluent of all experiments were not much
different, indicating the same range of treatment performance. The
biogas production decreased at higher ULV and ULV of 4 m/h is
suggested as design criterion for EGSB system.
Abstract: The aim of the article is extending and developing
econometrics and network structure based methods which are able to
distinguish price manipulation in Tehran stock exchange. The
principal goal of the present study is to offer model for
approximating price manipulation in Tehran stock exchange. In order
to do so by applying separation method a sample consisting of 397
companies accepted at Tehran stock exchange were selected and
information related to their price and volume of trades during years
2001 until 2009 were collected and then through performing runs
test, skewness test and duration correlative test the selected
companies were divided into 2 sets of manipulated and non
manipulated companies. In the next stage by investigating
cumulative return process and volume of trades in manipulated
companies, the date of starting price manipulation was specified and
in this way the logit model, artificial neural network, multiple
discriminant analysis and by using information related to size of
company, clarity of information, ratio of P/E and liquidity of stock
one year prior price manipulation; a model for forecasting price
manipulation of stocks of companies present in Tehran stock
exchange were designed. At the end the power of forecasting models
were studied by using data of test set. Whereas the power of
forecasting logit model for test set was 92.1%, for artificial neural
network was 94.1% and multi audit analysis model was 90.2%;
therefore all of the 3 aforesaid models has high power to forecast
price manipulation and there is no considerable difference among
forecasting power of these 3 models.
Abstract: Recently, content delivery services have grown rapidly
over the Internet. For ASPs (Application Service Provider) providing
content delivery services, P2P architecture is beneficial to reduce
outgoing traffic from content servers. On the other hand, ISPs are
suffering from the increase in P2P traffic. The P2P traffic is
unnecessarily redundant because the same content or the same
fractions of content are transferred through an inter-ISP link several
times. Subscriber ISPs have to pay a transit fee to upstream ISPs based
on the volume of inter-ISP traffic. In order to solve such problems,
several works have been done for the purpose of P2P traffic reduction.
However, these existing works cannot control the traffic volume of a
certain link. In order to solve such an ISP-s operational requirement,
we propose a method to control traffic volume for a link within a
preconfigured upper bound value. We evaluated that the proposed
method works well by conducting a simulation on a 1,000-user scale.
We confirm that the traffic volume could be controlled at a lower level
than the upper bound for all evaluated conditions. Moreover, our
method could control the traffic volume at 98.95% link usage against
the target value.
Abstract: In intensity modulated radiation therapy (IMRT)
treatment planning, beam angles are usually preselected on the basis of
experience and intuition. Therefore, getting an appropriate beam
configuration needs a very long time. Based on the present situation,
the paper puts forward beam orientation optimization using ant colony
optimization (ACO). We use ant colony optimization to select the
beam configurations, after getting the beam configuration using
Conjugate Gradient (CG) algorithm to optimize the intensity profiles.
Combining with the information of the effect of pencil beam, we can
get the global optimal solution accelerating. In order to verify the
feasibility of the presented method, a simulated and clinical case was
tested, compared with dose-volume histogram and isodose line
between target area and organ at risk. The results showed that the
effect was improved after optimizing beam configurations. The
optimization approach could make treatment planning meet clinical
requirements more efficiently, so it had extensive application
perspective.
Abstract: The rheological properties of light crude oil and its mixture with water were investigated experimentally. These rheological properties include steady flow behavior, yield stress, transient flow behavior, and viscoelastic behavior. A RheoStress RS600 rheometer was employed in all of the rheological examination tests. The light crude oil exhibits a Newtonian and for emulsion exhibits a non-Newtonian shear thinning behavior over the examined shear rate range of 0.1–120 s-1. In first time, a series of samples of crude oil from the Algerian Sahara has been tested and the results expressed in terms of τ=f(γ) have demonstrated their Newtonian character for the temperature included in [20°C, 70°C]. In second time and at T=20°C, the oil-water emulsions (30%, 50% and 70%) by volume of water), thermodynamically stable, have demonstrated a non-Newtonian rheological behavior that is to say, Herschel-Bulkley and Bingham types. For each type of crude oil-water emulsion, the rheological parameters are calculated by numerical treatment of results.
Abstract: Analysis of blood vessel mechanics in normal and
diseased conditions is essential for disease research, medical device
design and treatment planning. In this work, 3D finite element
models of normal vessel and atherosclerotic vessel with 50% plaque
deposition were developed. The developed models were meshed
using finite number of tetrahedral elements. The developed models
were simulated using actual blood pressure signals. Based on the
transient analysis performed on the developed models, the parameters
such as total displacement, strain energy density and entropy per unit
volume were obtained. Further, the obtained parameters were used to
develop artificial neural network models for analyzing normal and
atherosclerotic blood vessels. In this paper, the objectives of the
study, methodology and significant observations are presented.
Abstract: This paper proposes a method for speckle reduction in
medical ultrasound imaging while preserving the edges with the
added advantages of adaptive noise filtering and speed. A nonlinear
image diffusion method that incorporates local image parameter,
namely, scatterer density in addition to gradient, to weight the
nonlinear diffusion process, is proposed. The method was tested for
the isotropic case with a contrast detail phantom and varieties of
clinical ultrasound images, and then compared to linear and some
other diffusion enhancement methods. Different diffusion parameters
were tested and tuned to best reduce speckle noise and preserve
edges. The method showed superior performance measured both
quantitatively and qualitatively when incorporating scatterer density
into the diffusivity function. The proposed filter can be used as a
preprocessing step for ultrasound image enhancement before
applying automatic segmentation, automatic volumetric calculations,
or 3D ultrasound volume rendering.
Abstract: Three reactor types were explored and successfully
used for pigment production by Monascus: shake flasks, and shaken
and stirred miniaturized reactors. Also, the use of dielectric
spectroscopy for the on-line measurement of biomass levels was
explored. Shake flasks gave good pigment yields, but scale up is
difficult, and they cannot be automated. Shaken bioreactors were less
successful with pigment production than stirred reactors.
Experiments with different impeller speeds in different volumes of
liquid in the reactor confirmed that this is most likely due oxygen
availability. The availability of oxygen appeared to affect biomass
levels less than pigment production; red pigment production in
particular needed very high oxygen levels. Dielectric spectroscopy
was effectively used to continuously measure biomass levels during
the submerged fungal fermentation in the shaken and stirred
miniaturized bioreactors, despite the presence of the solid substrate
particles. Also, the capacitance signal gave useful information about
the viability of the cells in the culture.
Abstract: Construction cost in India is increasing at around 50
per cent over the average inflation levels. It have registered increase
of up to 15 per cent every year, primarily due to cost of basic
building materials such as steel, cement, bricks, timber and other
inputs as well as cost of labour. As a result, the cost of construction
using conventional building materials and construction is becoming
beyond the affordable limits particularly for low-income groups of
population as well as a large cross section of the middle - income
groups. Therefore, there is a need to adopt cost-effective construction
methods either by up-gradation of traditional technologies using local
resources or applying modern construction materials and techniques
with efficient inputs leading to economic solutions. This has become
the most relevant aspect in the context of the large volume of housing
to be constructed in both rural and urban areas and the consideration
of limitations in the availability of resources such as building
materials and finance. This paper makes an overview of the housing
status in India and adoption of appropriate and cost effective
technologies in the country.
Abstract: Due to the deregulation of the Electric Supply
Industry and the resulting emergence of electricity market, the
volumes of power purchases are on the rise all over the world. In a
bid to meet the customer-s demand in a reliable and yet economic
manner, utilities purchase power from the energy market over and
above its own production. This paper aims at developing an optimal
power purchase model with two objectives viz economy and
environment ,taking various functional operating constraints such as
branch flow limits, load bus voltage magnitudes limits, unit capacity
constraints and security constraints into consideration.The price of
purchased power being an uncertain variable is modeled using fuzzy
logic. DEMO (Differential Evolution For Multi-objective
Optimization) is used to obtain the pareto-optimal solution set of the
multi-objective problem formulated. Fuzzy set theory has been
employed to extract the best compromise non-dominated solution.
The results obtained on IEEE 30 bus system are presented and
compared with that of NSGAII.
Abstract: Whereas in the third generation nuclear reactors,
dimensions of core and also the kind of coolant and enrichment
percent of fuel have significantly changed than the second
generation, therefore in this article the aim is based on a
comparative investigation between two same power reactors of
second and third generations, that the neutronic parameters of both
reactors such as: K∞, Keff and its details and thermal hydraulic
parameters such as: power density, specific power, volumetric heat
rate, released power per fuel volume unit, volume and mass of clad
and fuel (consisting fissile and fertile fuels), be calculated and
compared together. By this comparing the efficiency and
modification of third generation nuclear reactors than second
generation which have same power can be distinguished.
In order to calculate the cited parameters, some information
such as: core dimensions, the pitch of lattice, the fuel matter, the
percent of enrichment and the kind of coolant are used. For
calculating the neutronic parameters, a neutronic program entitled:
SIXFAC and also related formulas have been used. Meantime for
calculating the thermal hydraulic and other parameters, analytical
method and related formulas have been applied.
Abstract: The purpose of this study was to explore the complex
flow structure a novel active-type micromixer that based on concept of
Wankle-type rotor. The characteristics of this micromixer are two
folds; a rapid mixing of reagents in a limited space due to the
generation of multiple vortices and a graduate increment in dynamic
pressure as the mixed reagents is delivered to the output ports.
Present micro-mixer is consisted of a rotor with shape of triangle
column, a blending chamber and several inlet and outlet ports. The
geometry of blending chamber is designed to make the rotor can be
freely internal rotated with a constant eccentricity ratio. When the
shape of the blending chamber and the rotor are fixed, the effects of
rotating speed of rotor and the relative locations of ports on the mixing
efficiency are numerical studied. The governing equations are
unsteady, two-dimensional incompressible Navier-Stokes equation
and the working fluid is the water. The species concentration equation
is also solved to reveal the mass transfer process of reagents in various
regions then to evaluate the mixing efficiency.
The dynamic mesh technique was implemented to model the
dynamic volume shrinkage and expansion of three individual
sub-regions of blending chamber when the rotor conducted a complete
rotating cycle. Six types of ports configuration on the mixing
efficiency are considered in a range of Reynolds number from 10 to
300. The rapid mixing process was accomplished with the multiple
vortex structures within a tiny space due to the equilibrium of shear
force, viscous force and inertial force. Results showed that the highest
mixing efficiency could be attained in the following conditions: two
inlet and two outlet ports configuration, that is an included angle of 60
degrees between two inlets and an included angle of 120 degrees
between inlet and outlet ports when Re=10.
Abstract: In this paper, a one-dimensional numerical approach is
used to study the effect of applying electrohydrodynamics on the
temperature and species mass fraction profiles along the microcombustor.
Premixed mixture is H2-Air with a multi-step chemistry
(9 species and 19 reactions). In the micro-scale combustion because
of the increasing ratio of area-to-volume, thermal and radical
quenching mechanisms are important. Also, there is a significant heat
loss from the combustor walls. By inserting a number of electrodes
into micro-combustor and applying high voltage to them corona
discharge occurs. This leads in moving of induced ions toward
natural molecules and colliding with them. So this phenomenon
causes the movement of the molecules and reattaches the flow to the
walls. It increases the velocity near the walls that reduces the wall
boundary layer. Consequently, applying electrohydrodynamics
mechanism can enhance the temperature profile in the microcombustor.
Ultimately, it prevents the flame quenching in microcombustor.
Abstract: The influence of viscosity on droplet diameter for
water-in-crude oil (w/o) emulsion with two different ratios; 20-80 %
and 50-50 % w/o emulsion was examined in the Brookfield
Rotational Digital Rheometer. The emulsion was prepared with
sorbitan sesquiolate (Span 83) act as emulsifier at varied temperature
and stirring speed in rotation per minute (rpm). Results showed that
the viscosity of w/o emulsion was strongly augmented by increasing
volume of water and decreased the temperature. The changing of
viscosity also altered the droplet size distribution. Changing of
droplet diameter was depends on the viscosity and the behavior of
emulsion either Newtonian or non-Newtonian.
Abstract: An accurate and proficient artificial neural network
(ANN) based genetic algorithm (GA) is developed for predicting of
nanofluids viscosity. A genetic algorithm (GA) is used to optimize
the neural network parameters for minimizing the error between the
predictive viscosity and the experimental one. The experimental
viscosity in two nanofluids Al2O3-H2O and CuO-H2O from 278.15
to 343.15 K and volume fraction up to 15% were used from
literature. The result of this study reveals that GA-NN model is
outperform to the conventional neural nets in predicting the viscosity
of nanofluids with mean absolute relative error of 1.22% and 1.77%
for Al2O3-H2O and CuO-H2O, respectively. Furthermore, the results
of this work have also been compared with others models. The
findings of this work demonstrate that the GA-NN model is an
effective method for prediction viscosity of nanofluids and have
better accuracy and simplicity compared with the others models.