Abstract: Lightweight and efficient structures have the aim to
enhance the efficiency of the components in various industries.
Toward this end, composites are one of the most widely used
materials because of durability, high strength and modulus, and low
weight. One type of the advanced composites is grid-stiffened
composite (GSC) structures, which have been extensively considered
in aerospace, automotive, and aircraft industries. They are one of the
top candidates for replacing some of the traditional components,
which are used here. Although there are a good number of published
surveys on the design aspects and fabrication of GSC structures, little
systematic work has been reported on their material modification to
improve their properties, to our knowledge. Matrix modification
using nanoparticles is an effective method to enhance the flexural
properties of the fibrous composites. In the present study, a silanecoupling
agent (3-glycidoxypropyltrimethoxysilane/3-GPTS) was
introduced onto the silica (SiO2) nanoparticle surface and its effects
on the three-point flexural response of isogrid E-glass/epoxy
composites were assessed. Based on the Fourier Transform Infrared
Spectrometer (FTIR) spectra, it was inferred that the 3-GPTS
coupling agent was successfully grafted onto the surface of SiO2
nanoparticles after modification. Flexural test revealed an
improvement of 16%, 14%, and 36% in stiffness, maximum load and
energy absorption of the isogrid specimen filled with 3 wt.% 3-
GPTS/SiO2 compared to the neat one. It would be worth mentioning
that in these structures, considerable energy absorption was observed
after the primary failure related to the load peak. In addition, 3-
GPTMS functionalization had a positive effect on the flexural
behavior of the multiscale isogrid composites. In conclusion, this
study suggests that the addition of modified silica nanoparticles is a
promising method to improve the flexural properties of the gridstiffened
fibrous composite structures.
Abstract: The floor beams of steel buildings, cold-formed steel
floor joists in particular, often require large web openings, which may
affect their shear capacities. A cost effective way to mitigate the
detrimental effects of such openings is to weld/fasten reinforcements.
A difficulty associated with an experimental investigation to establish
suitable reinforcement schemes for openings in shear zone is that
moment always coexists with the shear, and thus, it is impossible to
create pure shear state in experiments, resulting in moment
influenced results. However, Finite Element Method (FEM) based
analysis can be conveniently used to investigate the pure shear
behaviour of webs including webs with reinforced openings. This
paper presents the details associated with the finite element analysis
of thick/thin-plates (representing the web of hot-rolled steel beam,
and the web of a cold-formed steel member) having a large
reinforced opening. The study considered simply-supported
rectangular plates subjected to in-plane shear loadings until failure
(including post-buckling behaviour). The plate was modelled using
geometrically non-linear quadrilateral shell elements, and non-linear
stress-strain relationship based on experiments. Total Langrangian
with large displacement/small strain formulation was used for such
analyses. The model also considered the initial geometric
imperfections. This study considered three reinforcement schemes,
namely, flat, lip, and angle reinforcements. This paper discusses the
modelling considerations and presents the results associated with the
various reinforcement schemes under consideration.
Abstract: Within this paper, latest results on processing of energetic nanomaterials by means of the Spray Flash Evaporation technique are presented. This technology constitutes a highly effective and continuous way to prepare fascinating materials on the nano- and micro-scale. Within the process, a solution is set under high pressure and sprayed into an evacuated atomization chamber. Subsequent ultrafast evaporation of the solvent leads to an aerosol stream, which is separated by cyclones or filters. No drying gas is required, so the present technique should not be confused with spray dying. Resulting nanothermites, insensitive explosives or propellants and compositions are foreseen to replace toxic (according to REACH) and very sensitive matter in military and civil applications. Diverse examples are given in detail: nano-RDX (n-Cyclotrimethylentrinitramin) and nano-aluminum based systems, mixtures (n-RDX/n-TNT - trinitrotoluene) or even cocrystalline matter like n-CL-20/HMX (Hexanitrohexaazaisowurtzitane/ Cyclotetra-methylentetranitramin). These nanomaterials show reduced sensitivity by trend without losing effectiveness and performance. An analytical study for material characterization was performed by using Atomic Force Microscopy, X-Ray Diffraction, and combined techniques as well as spectroscopic methods. As a matter of course, sensitivity tests regarding electrostatic discharge, impact, and friction are provided.
Abstract: The current study focuses on the seismic design of
offshore pipelines against active faults. After an extensive literature
review of the provisions of the seismic norms worldwide and of the
available analytical methods, the study simulates numerically
(through finite-element modeling and strain-based criteria) the
distress of offshore pipelines subjected to PGDs induced by active
normal and reverse seismic faults at the seabed. Factors, such as the
geometrical properties of the fault, the mechanical properties of the
ruptured soil formations, and the pipeline characteristics, are
examined. After some interesting conclusions regarding the seismic
vulnerability of offshore pipelines, potential cost-effective mitigation
measures are proposed taking into account constructability issues.
Abstract: The noise is one of the negative elements which
affects the human health. This article presents the measurement of
emitted noise by road vehicle and its parts during the operation.
Measurement was done in the interior of common passenger cars
with a digital sound meter. The results compare the noise value in
different cars with different body shape, which influences the driver’s
health. Transport has considerable ecological effects; many of them
are detrimental to environmental sustainability. Roads and traffic
exert a variety of direct and mostly detrimental effects on nature.
Abstract: Carbon Fiber Reinforced Plastics (CFRPs) are widely
used for advanced applications, in particular in aerospace, automotive
and wind energy industries. Once cured to near net shape, CFRP
parts need several finishing operations such as trimming, milling or
drilling in order to accommodate fastening hardware and meeting the
final dimensions. The present research aims to study the effect of the
cutting temperature in trimming on the mechanical strength of high
performance CFRP laminates used for aeronautics applications. The
cutting temperature is of great importance when dealing with
trimming of CFRP. Temperatures higher than the glass-transition
temperature (Tg) of the resin matrix are highly undesirable: they
cause degradation of the matrix in the trimmed edges area, which can
severely affect the mechanical performance of the entire component.
In this study, a 9.50mm diameter CVD diamond coated carbide tool
with six flutes was used to trim 24-plies CFRP laminates. A
300m/min cutting speed and 1140mm/min feed rate were used in the
experiments. The tool was heated prior to trimming using a
blowtorch, for temperatures ranging from 20°C to 300°C. The
temperature at the cutting edge was measured using embedded KType
thermocouples. Samples trimmed for different cutting
temperatures, below and above Tg, were mechanically tested using
three-points bending short-beam loading configurations. New cutting
tools as well as worn cutting tools were utilized for the experiments.
The experiments with the new tools could not prove any correlation
between the length of cut, the cutting temperature and the mechanical
performance. Thus mechanical strength was constant, regardless of
the cutting temperature. However, for worn tools, producing a cutting
temperature rising up to 450°C, thermal damage of the resin was
observed. The mechanical tests showed a reduced mean resistance in
short beam configuration, while the resistance in three point bending
decreases with increase of the cutting temperature.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: High frequency automotive interior noise above 500
Hz considerably affects automotive passenger comfort. To reduce this
noise, sound insulation material is often laminated on body panels or
interior trim panels. For a more effective noise reduction, the sound
reduction properties of this laminated structure need to be estimated.
We have developed a new calculate tool that can roughly calculate the
sound absorption and insulation properties of laminate structure and
handy for designers. In this report, the outline of this tool and an
analysis example applied to floor mat are introduced.
Abstract: STRIM (Statistical Test Rule Induction Method) has been proposed as a method to effectively induct if-then rules from the decision table which is considered as a sample set obtained from the population of interest. Its usefulness has been confirmed by simulation experiments specifying rules in advance, and by comparison with conventional methods. However, scope for future development remains before STRIM can be applied to the analysis of real-world data sets. The first requirement is to determine the size of the dataset needed for inducting true rules, since finding statistically significant rules is the core of the method. The second is to examine the capacity of rule induction from datasets with contaminated attribute values created by missing data and noise, since real-world datasets usually contain such contaminated data. This paper examines the first problem theoretically, in connection with the rule length. The second problem is then examined in a simulation experiment, utilizing the critical size of dataset derived from the first step. The experimental results show that STRIM is highly robust in the analysis of datasets with contaminated attribute values, and hence is applicable to real-world data
Abstract: Complex lifting entry was selected for precise landing
performance during the Mars Science Laboratory entry. This study
aims to develop the three-dimensional numerical method for precise
computation and the surface panel method for rapid engineering
prediction. Detailed flow field analysis for Mars exploration mission
was performed by carrying on a series of fully three-dimensional
Navier-Stokes computations. The static aerodynamic performance was
then discussed, including the surface pressure, lift and drag coefficient,
lift-to-drag ratio with the numerical and engineering method.
Computation results shown that the shock layer is thin because of
lower effective specific heat ratio, and that calculated results from both
methods agree well with each other, and is consistent with the
reference data. Aerodynamic performance analysis shows that CG
location determines trim characteristics and pitch stability, and certain
radially and axially shift of the CG location can alter the capsule lifting
entry performance, which is of vital significance for the aerodynamic
configuration design and inner instrument layout of the Mars entry
capsule.
Abstract: Forward Osmosis (FO) polyamide thin-film composite
membranes have been prepared by interfacial polymerization using
commercial UF polyethersulfoneas membrane support. Different
interfacial polymerization times (10s, 30s and 60s) in the organic
solution containing trimesoyl chloride (TMC) at constant m-phenylenediamine
(MPD) concentration (2% w/v) were studied. The
synthesized polyamide membranes then tested for treatment of
natural organic matter (NOM) and compared to commercial Cellulose
TriAcetate (CTA) membrane. It was found that membrane prepared
with higher reaction time (30s and 60s) exhibited better membrane
performance (flux and humic acid removal) over commercial CTA
membrane.
Abstract: The textile industry plays a major role in the economy
of India and on the other side of the coin it is the major source for
water pollution. As azo dyes is the largest dye class they are
extensively used in many fields such as textile industry, leather
tanning industry, paper production, food, color photography,
pharmaceuticals and medicine, cosmetic, hair colorings, wood
staining, agricultural, biological and chemical research etc. In
addition to these, they can have acute and/or chronic effects on
organisms depending on their concentration and length of exposure
when they discharged as effluent in the environment. The aim of this
study was to assess the genotoxic and histotoxic potentials of
environmentally relevant concentrations of C. I. Reactive Red 120
(RR 120) on Catla catla, important edible freshwater fingerlings. For
this, healthy Catla catla fingerlings were procured from the
Government Fish Farm and acclimatized in 100 L capacity and
continuously aerated glass aquarium in laboratory for 15 days.
According to APHA some physic-chemical parameters were
measured and maintained such as temperature, pH, dissolve oxygen,
alkalinity, total hardness. Water along with excreta had been changed
every 24 hrs. All fingerlings were fed artificial food palates once a
day @ body weight. After 15 days fingerlings were grouped in 5 (10
in each) and exposed to various concentrations of RR 120 (Control,
10, 20, 30 and 40 mg.l-1) and samples (peripheral blood and gills,
kidney) were collected and analyzed at 96 hrs. All results were
compared with the control. Micronuclei (MN), nuclear buds (NB),
fragmented-apoptotic (FA) and bi-nucleated (BN) cells in blood
smears and in tissues (gills and kidney cells) were observed.
Prominent histopathological alterations were noticed in gills such as
aneurism, hyperplasia, degenerated central axis, lifting of gill
epithelium, curved secondary gill lamellae etc. Similarly kidney
showed some detrimental changes like shrunken glomeruli with
increased periglomerular space, degenerated renal tubules etc. Both
haematological and histopathological changes clearly reveal the toxic
potential of RR 120. This work concludes that water pollution
assessment can be done by these two biomarkers which provide
baseline to the further chromosomal or molecular work.
Abstract: Freshly laid eggs from green turtles, Chelonia mydas,
were randomly collected from Ras Al-Hadd Reserve, Oman.
Eggshells taken from eggs and sand collected from the body chamber
were analyzed for eight heavy metals (Al, Br, Cd, Co, Cu, Fe, S, and
Zn) using inductively coupled plasma mass spectrometry (ICP).
Heavy metal concentrations varied significantly (P
Abstract: This paper argues nation-building theories that
prioritize democratic governance best explain the successful postindependence
development of Botswana. Three main competing
schools of thought exist regarding the sequencing of policies that
should occur to re-build weakened or failed states. The first posits
that economic development should receive foremost attention, while
democratization and a binding sense of nationalism can wait. A
second group of experts identified constructing a sense of nationalism
among a populace is necessary first, so that the state receives popular
legitimacy and obedience that are prerequisites for development.
Botswana, though, transitioned into a multi-party democracy and
prosperous open economy due to the utilization of traditional
democratic structures, enlightened and accountable leadership, and an
educated technocratic civil service. With these political foundations
already in place when the discovery of diamonds occurred, the
resulting revenues were spent wisely on projects that grew the
economy, improved basic living standards, and attracted foreign
investment. Thus democratization preceded, and therefore provided
an accountable basis for, economic development that might otherwise
have been squandered by greedy and isolated elites to the detriment
of the greater population. Botswana was one of the poorest nations in
the world at the time of its independence in 1966, with little
infrastructure, a dependence on apartheid South Africa for trade, and
a largely subsistence economy. Over the next thirty years, though, its
economy grew the fastest of any nation in the world. The transparent
and judicious use of diamond returns is only a partial explanation, as
the government also pursued economic diversification, mass
education, and rural development in response to public needs.
As nation-building has become a project undertaken by nations
and multilateral agencies such as the United Nations and the North
Atlantic Treaty Organization, Botswana may provide best practices
that others should follow in attempting to reconstruct economically
and politically unstable states.
Abstract: In this paper, we investigate the effect of friendly
jamming power allocation strategies on the achievable average
secrecy rate over a bank of parallel fading wiretap channels.
We investigate the achievable average secrecy rate in parallel
fading wiretap channels subject to Rayleigh and Rician fading.
The achievable average secrecy rate, due to the presence of a
line-of-sight component in the jammer channel is also evaluated.
Moreover, we study the detrimental effect of correlation across the
parallel sub-channels, and evaluate the corresponding decrease in the
achievable average secrecy rate for the various fading configurations.
We also investigate the tradeoff between the transmission power
and the jamming power for a fixed total power budget. Our
results, which are applicable to current orthogonal frequency division
multiplexing (OFDM) communications systems, shed further light on
the achievable average secrecy rates over a bank of parallel fading
channels in the presence of friendly jammers.
Abstract: Unmanned aircraft systems (UAS) are playing
increasingly prominent roles in defense programs and defense
strategies around the world. Technology advancements have
enabled the development of it to do many excellent jobs as
reconnaissance, surveillance, battle fighters, and communications
relays. Simulating a small unmanned aerial vehicle (SUAV)
dynamics and analyzing its behavior at the preflight stage is too
important and more efficient. The first step in the UAV design is
the mathematical modeling of the nonlinear equations of motion. .
In this paper, a survey with a standard method to obtain the full
non-linear equations of motion is utilized, and then the
linearization of the equations according to a steady state flight
condition (trimming) is derived. This modeling technique is
applied to an Ultrastick-25e fixed wing UAV to obtain the valued
linear longitudinal and lateral models. At the end the model is
checked by matching between the behavior of the states of the nonlinear
UAV and the resulted linear model with doublet at the
control surfaces.
Abstract: This study investigates the cleaning performance of
high intensity 360 kHz frequency on removal of nano-dimensional
and sub-micron particles from various surfaces, uniformity of the
cleaning tank and run to run variation of cleaning process. The
uniformity of the cleaning tank was measured by two different
methods i.e. 1. ppbTM meter and 2. Liquid Particle Counting (LPC)
technique. The result indicates that the energy was distributed more
uniformly throughout the entire cleaning vessel even at the corners
and edges of the tank when megasonic sweeping technology is
applied. The result also shows that rinsing the parts with 360 kHz
frequency at final rinse gives lower particle counts, hence higher
cleaning efficiency as compared to other frequencies. When
megasonic sweeping technology is applied each piezoelectric
transducers will operate at their optimum resonant frequency and
generates stronger acoustic cavitational force and higher acoustic
streaming velocity. These combined forces are helping to enhance the
particle removal and at the same time improve the overall cleaning
performance. The multiple extractions study was also carried out for
various frequencies to measure the cleaning potential and asymptote
value.
Abstract: The present study was done to evaluate the presence
of tetracycline resistance genes in Lactococcus garvieae isolated
from cultured rainbow trout, West Iran. The isolates were examined
for antimicrobial resistance using disc diffusion method. Of the 49
strains tested, 19 were resistant to tetracycline (38.7%), 32 to
enrofloxacin (65.3%), 21 to erythromycin (42.8%), 20 to
chloramphenicol and trimetoprim-sulfamethoxazole (40.8%). The
strains were then characterized for their genotypic resistance profiles.
The results revealed that all 49 isolates contained at least one of the
tetracycline resistance genes. Tet (A) was found in 89.4% of
tetracycline resistant isolates and the frequency of other gene were as
follows: tet (E) 42.1%, tet (B) 47.3%, tet (D) 15.7%, tet (L) 26.3%,
tet (K) 52.6%, tet (G) 36.8%, tet (34) 21%, tet (S) 63.1%, tet (C)
57.8%, tet (M) 73.6%, tet (O) 42.1%. The results revealed high levels
of antibiotic resistance in L. garvieae strains which is a potential
danger for trout culture as well as for public health.
Abstract: In this study, the performance analyses of the twenty
five Coal-Fired Power Plants (CFPPs) used for electricity generation
are carried out through various Data Envelopment Analysis (DEA)
models. Three efficiency indices are defined and pursued. During the
calculation of the operational performance, energy and non-energy
variables are used as input, and net electricity produced is used as
desired output (Model-1). CO2 emitted to the environment is used as
the undesired output (Model-2) in the computation of the pure
environmental performance while in Model-3 CO2 emissions is
considered as detrimental input in the calculation of operational and
environmental performance. Empirical results show that most of the
plants are operating in increasing returns to scale region and Mettur
plant is efficient one with regards to energy use and environment.
The result also indicates that the undesirable output effect is
insignificant in the research sample. The present study will provide
clues to plant operators towards raising the operational and
environmental performance of CFPPs.
Abstract: Strong anion exchange resins with QN+OH-, have the
potential to be developed and employed as heterogeneous catalyst for
transesterification, as they are chemically stable to leaching of the
functional group. Nine different SIERs (SIER1-9) with QN+OH-were
prepared by suspension polymerization of vinylbenzyl chloridedivinylbenzene
(VBC-DVB) copolymers in the presence of n-heptane
(pore-forming agent). The amine group was successfully grafted into
the polymeric resin beads through functionalization with
trimethylamine. These SIERs are then used as a catalyst for the
transesterification of triacetin with methanol. A set of differential
equations that represents the Langmuir-Hinshelwood-Hougen-
Watson (LHHW) and Eley-Rideal (ER) models for the
transesterification reaction were developed. These kinetic models of
LHHW and ER were fitted to the experimental data. Overall, the
synthesized ion exchange resin-catalyzed reaction were welldescribed
by the Eley-Rideal model compared to LHHW models,
with sum of square error (SSE) of 0.742 and 0.996, respectively.