Abstract: In this paper, we present a simple circuit for
Manchester decoding and without using any complicated or
programmable devices. This circuit can decode 90kbps of transmitted
encoded data; however, greater than this transmission rate can be
decoded if high speed devices were used. We also present a new
method for extracting the embedded clock from Manchester data in
order to use it for serial-to-parallel conversion. All of our
experimental measurements have been done using simulation.
Abstract: An innovative tri-axes micro-power receiver is
proposed. The tri-axes micro-power receiver consists of two sets 3-D
micro-solenoids and one set planar micro-coils in which iron core is
embedded. The three sets of micro-coils are designed to be orthogonal
to each other. Therefore, no matter which direction the flux is present
along, the magnetic energy can be harvested and transformed into
electric power. Not only dead space of receiving power is mostly
reduced, but also transformation efficiency of electromagnetic energy
to electric power can be efficiently raised. By employing commercial
software, Ansoft Maxwell, the preliminary simulation results verify
that the proposed micro-power receiver can efficiently pick up the
energy transmitted by magnetic power source.
As to the fabrication process, the isotropic etching technique is
employed to micro-machine the inverse-trapezoid fillister so that the
copper wire can be successfully electroplated. The adhesion between
micro-coils and fillister is much enhanced.
Abstract: This paper focuses on wormhole attacks detection in wireless sensor networks. The wormhole attack is particularly challenging to deal with since the adversary does not need to compromise any nodes and can use laptops or other wireless devices to send the packets on a low latency channel. This paper introduces an easy and effective method to detect and locate the wormholes: Since beacon nodes are assumed to know their coordinates, the straight line distance between each pair of them can be calculated and then compared with the corresponding hop distance, which in this paper equals hop counts × node-s transmission range R. Dramatic difference may emerge because of an existing wormhole. Our detection mechanism is based on this. The approximate location of the wormhole can also be derived in further steps based on this information. To the best of our knowledge, our method is much easier than other wormhole detecting schemes which also use beacon nodes, and to those have special requirements on each nodes (e.g., GPS receivers or tightly synchronized clocks or directional antennas), ours is more economical. Simulation results show that the algorithm is successful in detecting and locating wormholes when the density of beacon nodes reaches 0.008 per m2.
Abstract: Protective relays are components of a protection system
in a power system domain that provides decision making element for
correct protection and fault clearing operations. Failure of the
protection devices may reduce the integrity and reliability of the power
system protection that will impact the overall performance of the
power system. Hence it is imperative for power utilities to assess the
reliability of protective relays to assure it will perform its intended
function without failure. This paper will discuss the application of
reliability analysis using statistical method called Life Data Analysis
in Tenaga Nasional Berhad (TNB), a government linked power utility
company in Malaysia, namely Transmission Division, to assess and
evaluate the reliability of numerical overcurrent protective relays from
two different manufacturers.
Abstract: This research paper evaluates and compares the
performance of equal cost adaptive multi-path routing algorithms
taking the transport protocols TCP (Transmission Control Protocol)
and UDP (User Datagram Protocol) using network simulator ns2 and
concludes which one is better.
Abstract: Directional over current relays (DOCR) are commonly used in power system protection as a primary protection in distribution and sub-transmission electrical systems and as a secondary protection in transmission systems. Coordination of protective relays is necessary to obtain selective tripping. In this paper, an approach for efficiency reduction of DOCRs nonlinear optimum coordination (OC) is proposed. This was achieved by modifying the objective function and relaxing several constraints depending on the four constraints classification, non-valid, redundant, pre-obtained and valid constraints. According to this classification, the far end fault effect on the objective function and constraints, and in consequently on relay operating time, was studied. The study was carried out, firstly by taking into account the near-end and far-end faults in DOCRs coordination problem formulation; and then faults very close to the primary relays (nearend faults). The optimal coordination (OC) was achieved by simultaneously optimizing all variables (TDS and Ip) in nonlinear environment by using of Genetic algorithm nonlinear programming techniques. The results application of the above two approaches on 6-bus and 26-bus system verify that the far-end faults consideration on OC problem formulation don-t lose the optimality.
Abstract: Among other factors that characterize satellite communication
channels is their high bit error rate. We present a system for
still image transmission over noisy satellite channels. The system
couples image compression together with error control codes to
improve the received image quality while maintaining its bandwidth
requirements. The proposed system is tested using a high resolution
satellite imagery simulated over the Rician fading channel. Evaluation
results show improvement in overall system including image quality
and bandwidth requirements compared to similar systems with different
coding schemes.
Abstract: Distance protection of transmission lines including advanced flexible AC transmission system (FACTS) devices has been a very challenging task. FACTS devices of interest in this paper are static synchronous series compensators (SSSC) and unified power flow controller (UPFC). In this paper, a new algorithm is proposed to detect and classify the fault and identify the fault position in a transmission line with respect to a FACTS device placed in the midpoint of the transmission line. Discrete wavelet transformation and wavelet entropy calculations are used to analyze during fault current and voltage signals of the compensated transmission line. The proposed algorithm is very simple and accurate in fault detection and classification. A variety of fault cases and simulation results are introduced to show the effectiveness of such algorithm.
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.
Abstract: TiO2/MgO composite films were prepared by coating
the magnesium acetate solution in the pores of mesoporous TiO2
films using a dip coating method. Concentrations of magnesium
acetate solution were varied in a range of 1x10-4 – 1x10-1 M. The
TiO2/MgO composite films were characterized by scanning electron
microscopy (SEM), transmission electron microscropy (TEM),
electrochemical impedance spectroscopy(EIS) , transient voltage
decay and I-V test. The TiO2 films and TiO2/MgO composite films
were immersed in a 0.3 mM N719 dye solution. The Dye-sensitized
solar cells with the TiO2/MgO/N719 structure showed an optimal
concentration of magnesium acetate solution of 1x10-3 M resulting in
the MgO film estimated thickness of 0.0963 nm and giving the
maximum efficiency of 4.85%. The improved efficiency of dyesensitized
solar cell was due to the magnesium oxide film as the wide
band gap coating decays the electron back transfer to the triiodide
electrolyte and reduce charge recombination.
Abstract: Perhaps no single issue has been cited as either the root
cause and / or the greatest challenge to the restructured power system then the lack of adequate reliable transmission. Probabilistic transmission planning has become increasingly necessary and important in recent
years. The transmission planning analysis carried out by the authors,
spans a 10-year horizon, taking into consideration a value of 2 % load
increase / year at each consumer. Taking into consideration this increased
load, a probabilistic power flow was carried out, all the system components
being regarded from probabilistic point of view. Several contingencies
have been generated, for assessing the security of the power system. The results have been analyzed and several important conclusions were pointed. The objective is to achieve a network that works without limit violations for all (or most of) scenario realizations. The case study is represented by the IEEE 14 buses test power system.
Abstract: This paper presents an application of power line
carrier (PLC) for electrical power telemetering. This system has a
special capability of transmitting the measured values to a centralized
computer via power lines. The PLC modem as a passive high-pass
filter is designed for transmitting and receiving information. Its
function is to send the information carrier together with transmitted
data by superimposing it on the 50 Hz power frequency signal. A
microcontroller is employed to function as the main processing of the
modem. It is programmed for PLC control and interfacing with other
devices. Each power meter, connected via a PLC modem, is assigned
with a unique identification number (address) for distinguishing each
device from one another.
Abstract: Dengue, a disease found in most tropical and
subtropical areas of the world. It has become the most common
arboviral disease of humans. This disease is caused by any of four
serotypes of dengue virus (DEN1-DEN4). In many endemic
countries, the average age of getting dengue infection is shifting
upwards, dengue in pregnancy and infancy are likely to be
encountered more frequently. The dynamics of the disease is studied
by a compartmental model involving ordinary differential equations
for the pregnant, infant human and the vector populations. The
stability of each equilibrium point is given. The epidemic dynamic is
discussed. Moreover, the numerical results are shown for difference
values of dengue antibody.
Abstract: This paper presents the mathematical model of electric field and magnetic field in transmission system, which performs in second-order partial differential equation. This research has conducted analyzing the electromagnetic field radiating to atmosphere around the transmission line, when there is the transmission line transposition in case of long distance distribution. The six types of 500 kV transposed HV transmission line with double circuit will be considered. The computer simulation is applied finite element method that is developed by MATLAB program. The problem is considered to two dimensions, which is time harmonic system with the graphical performance of electric field and magnetic field. The impact from simulation of six types long distance distributing transposition will not effect changing of electric field and magnetic field which surround the transmission line.
Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: The main objective of this paper is to provide an efficient tool for delineating brain tumors in three-dimensional magnetic resonance images and set up compression-transmit schemes to distribute result to the remote doctor. To achieve this goal, we use basically a level-sets approach to delineating brain tumors in threedimensional. Then introduce a new compression and transmission plan of 3D brain structures based for the meshes simplification, adapted for time to the specific needs of the telemedicine and to the capacities restricted by wireless network communication. We present here the main stages of our system, and preliminary results which are very encouraging for clinical practice.
Abstract: In this investigation, anatase TiO2 thin films were
grown by radio frequency magnetron sputtering on glass substrates at
a high sputtering pressure and room temperature. The anatase films
were then annealed at 300-600 °C in air for a period of 1 hour. To
examine the structure and morphology of the films, X-ray diffraction
(XRD) and atomic force microscopy (AFM) methods were used
respectively. From X-ray diffraction patterns of the TiO2 films, it was
found that the as-deposited film showed some differences compared
with the annealed films and the intensities of the peaks of the
crystalline phase increased with the increase of annealing
temperature. From AFM images, the distinct variations in the
morphology of the thin films were also observed. The optical
constants were characterized using the transmission spectra of the
films obtained by UV-VIS-IR spectrophotometer. Besides, optical
thickness of the film deposited at room temperature was calculated
and cross-checked by taking a cross-sectional image through SEM.
The optical band gaps were evaluated through Tauc model. It was
observed that TiO2 films produced at room temperatures exhibited
high visible transmittance and transmittance decreased slightly with
the increase of annealing temperatures. The films were found to be
crystalline having anatase phase. The refractive index of the films
was found from 2.31-2.35 in the visible range. The extinction
coefficient was nearly zero in the visible range and was found to
increase with annealing temperature. The allowed indirect optical
band gap of the films was estimated to be in the range from 3.39 to
3.42 eV which showed a small variation. The allowed direct band
gap was found to increase from 3.67 to 3.72 eV. The porosity was
also found to decrease at a higher annealing temperature making the
film compact and dense.
Abstract: In this paper, we present a robust and secure
algorithm for watermarking, the watermark is first transformed into
the frequency domain using the discrete wavelet transform (DWT).
Then the entire DWT coefficient except the LL (Band) discarded,
these coefficients are permuted and encrypted by specific mixing.
The encrypted coefficients are inserted into the most significant
spectral components of the stego-image using a chaotic system. This
technique makes our watermark non-vulnerable to the attack (like
compression, and geometric distortion) of an active intruder, or due
to noise in the transmission link.
Abstract: The third generation (3G) of cellular system adopted
the spread spectrum as solution for the transmission of the data in the
physical layer. Contrary to systems IS-95 or CDMAOne (systems
with spread spectrum of the preceding generation), the new standard,
called Universal Mobil Telecommunications System (UMTS), uses
long codes in the down link. The system is conceived for the vocal
communication and the transmission of the data. In particular, the
down link is very important, because of the asymmetrical request of
the data, i.e., more remote loading towards the mobiles than towards
the basic station. Moreover, the UMTS uses for the down link an
orthogonal spreading out with a variable factor of spreading out
(OVSF for Orthogonal Variable Spreading Factor). This
characteristic makes it possible to increase the flow of data of one or
more users by reducing their factor of spreading out without
changing the factor of spreading out of other users. In the current
standard of the UMTS, two techniques to increase the performances
of the down link were proposed, the diversity of sending antenna and
the codes space-time. These two techniques fight only fainding. The
receiver proposed for the mobil station is the RAKE, but one can
imagine a receiver more sophisticated, able to reduce the interference
between users and the impact of the coloured noise and interferences
to narrow band. In this context, where the users have long codes
synchronized with variable factor of spreading out and ignorance by
the mobile of the other active codes/users, the use of the sequences of
code pseudo-noises different lengths is presented in the form of one
of the most appropriate solutions.
Abstract: Bluetooth is a personal wireless communication
technology and is being applied in many scenarios. It is an emerging
standard for short range, low cost, low power wireless access
technology. Current existing MAC (Medium Access Control)
scheduling schemes only provide best-effort service for all masterslave
connections. It is very challenging to provide QoS (Quality of
Service) support for different connections due to the feature of
Master Driven TDD (Time Division Duplex). However, there is no
solution available to support both delay and bandwidth guarantees
required by real time applications. This paper addresses the issue of
how to enhance QoS support in a Bluetooth piconet. The Bluetooth
specification proposes a Round Robin scheduler as possible solution
for scheduling the transmissions in a Bluetooth Piconet. We propose
an algorithm which will reduce the bandwidth waste and enhance the
efficiency of network. We define token counters to estimate traffic of
real-time slaves. To increase bandwidth utilization, a back-off
mechanism is then presented for best-effort slaves to decrease the
frequency of polling idle slaves. Simulation results demonstrate that
our scheme achieves better performance over the Round Robin
scheduling.